Помогите грамотно настроить модем IDC5614BXL/V по статистике

[softmaster]

Inpro IDC Modems Diagnostics, Version: 1.1.4.39
12.01.2005 12:06:05 - Outbound Call By RemoteAccess
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.26
Time Online.................. 05:24:00
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 24000/24000/24000/24000 bps
Rx Rate (Last/Init/Min/Max).. 28800/31200/24000/31200 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 38
Tx/Power Drop/Rx Level....... 13/0/36
SNR Last/Min/Max............. 43/43/43
Highest Rx/Tx State.......... 85/87
EQM Sum...................... 0022
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 8/0
FForwards/FBacks/FEQM/Denied. 4/4/0/0
Forced FB/FB after FF/MaxREJ. 2/2/10
Last dialed number........... P3334245
Flex fail


Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 3200
Carrier Frequency Hz, Rx/Tx.. 1829/1829
EQM Value (Last/Min/Max)..... 38/12/127
EQM Hits..................... 0
EQM Last 10 Readings......... 34 39 41 32 38 35 34 36 35 35
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallforward due to Low EQM
Last Retrain/Reneg Time...... 11 minutes ago
Handshake Time/Retries....... 17 seconds/0
Non-linear Encoding, Rx/Tx... ON/ON
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 5
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 8,8
Last Rx/Tx State............. 85/87
Energy at 3750Hz/Average .... 75/14
Rx Level (Last/Min/Max), -dB. 35,3/37,6/35,3
Detection of 120 Hz Tones.... No
Detection of Dual PCM........ No
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/237
Frames Errors, Rx/Tx......... 749/10 (0,2%/0,0%)
Frames Count, Rx/Tx.......... 305229/101112
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 67
Error Control Link NAKs...... 10
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 40 681 267
Characters Sent.............. 2 691 498
Average CPS, Rx/Tx........... 2092/138
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 79


использую строку иницилизации
ats111=5+A8E=,,,0s91=13s210.7=1+ms=11,,,,,,33600

[softmaster]

Неужели так не кто и ни не поможет

[Technical Support]

А что, собственно, не устраивает в работе модема? Результат вполне соответствует качеству линии...
_________________
Inpro
Technical Support

[softmaster]

Прошу помочь разобраться со строкой инициализации
вот данные без нее

Inpro IDC Modems Diagnostics, Version: 1.1.4.39
25.01.2005 6:43:59 - Outbound Call By RemoteAccess
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.25
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: <none>

Time Online.................. 00:00:21
Termination Reason........... LINK DISCONNECT
Tx Rate (Last/Init/Min/Max).. 9600/ 9600/ 9600/ 9600 bps
Rx Rate (Last/Init/Min/Max).. 38667/38667/38667/38667 bps
Modulation................... V.90
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 28
Tx/Power Drop/Rx Level....... 15/0/21
SNR Last/Min/Max............. 43/43/43
Highest Rx/Tx State.......... 67/67
EQM Sum...................... 010A
RBS Pattern.................. 00
Rate Drop.................... 0
Digital Loss................. 2000
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 0/0
FForwards/FBacks/Denied...... 0/0/0
Forced FB/FB after FF/MaxREJ. 0/0/0
Last dialed number........... P3334245
V90 9481834246E0


Negotiation Result (Rx/Tx)... V.90 Issue 1 (asymmetric)/V.34
Symbol Rate (Rx/Tx).......... 8000/3200
Carrier Frequency Hz, Tx..... 1829
EQM Value (Last/Min/Max)..... 28/25/32
EQM Hits..................... 0
EQM Last 10 Readings......... 30 25 28 28 27 30 28 28 27 26
Fast Retrains (RRWS) Count... 0
Last Retrain/Reneg Status.... None
Last Retrain/Reneg Reason.... None
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 23 seconds/0
Non-linear Encoding, Rx/Tx... OFF/OFF
Precoding, Rx/Tx............. OFF/OFF
Shaping, Rx/Tx............... OFF/OFF
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 0
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 3,2
Last Rx/Tx State............. 67/67
Energy at 3750Hz/Average .... 157/27
Auto Gain Amplitude, db...... 15
Rx Level (Last/Min/Max), -dB. 19,8/19,8/19,8
Detection of 120 Hz Tones.... Yes
Detection of Dual PCM........ No
V.90 RBS Pattern............. 00
V.90 Alternating RBS Pattern. 00
V.90 Digital Pad Value, db... 0,0
V.90 Optimal Speed........... 40000 bps (Reg.S120=10)
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 02
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Server (Digital)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. SYNC UA:T UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/0
Frames Errors, Rx/Tx......... 0/0 (0,0%/0,0%)
Frames Count, Rx/Tx.......... 140/135
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 0
Error Control Link NAKs...... 0
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 3 177
Characters Sent.............. 3 546
Average CPS, Rx/Tx........... 151/168
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 64

хотелось бы максимум но чтоб соединение оставалось стабильным !!!
Вообще модем супер лучше zyxelya

[Technical Support]

Сделайте следующее:

1. Установите микропрограмму версии 2.26. Для установки удобнее всего воспользоваться загрузчиком FldrWin/VR, который можно взять на этом сайте, в разделе "Микропрограммы".

2. Запустите терминальную программу (например, Hyperterminal) и выполните команду:

at *nc22 w2 \v1 s95=3 &w &w1
OK

3. Пропишите такую строку инициализации:

S91=15 S210.7=1 S17=64 +MS=,,,40000

и покажите, что получается в статистике. Сеанс должен длиться хотя бы 5 минут. Во время сеанса нужно обеспечить загрузку модема на приём (скачайте какой-нибудь архивированный файл).
_________________
Inpro
Technical Support

[softmaster]

Inpro IDC Modems Diagnostics, Version: 1.1.4.39
26.01.2005 9:12:45 - Outbound Call By RemoteAccess
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.25
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: S91=15 S210.7=1 S17=64 +MS=,,,40000

Time Online.................. 00:15:41
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 24000/24000/24000/24000 bps
Rx Rate (Last/Init/Min/Max).. 40000/40000/40000/40000 bps
Modulation................... V.90
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 44
Tx/Power Drop/Rx Level....... 15/0/21
SNR Last/Min/Max............. 43/43/43
Highest Rx/Tx State.......... 67/87
EQM Sum...................... 00EC
RBS Pattern.................. 00
Rate Drop.................... 0
Digital Loss................. 2000
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 1/0
FForwards/FBacks/FEQM/Denied. 0/1/0/0
Forced FB/FB after FF/MaxREJ. 1/0/7
Last dialed number........... P3334245
V90 9481834347EB


Negotiation Result (Rx/Tx)... V.90 Issue 1 (asymmetric)/V.34
Symbol Rate (Rx/Tx).......... 8000/3200
Carrier Frequency Hz, Tx..... 1829
EQM Value (Last/Min/Max)..... 44/16/57
EQM Hits..................... 0
EQM Last 10 Readings......... 43 45 43 43 45 48 46 45 49 47
Fast Retrains (RRWS) Count... 1
Last Retrain/Reneg Status.... Local Fast Retrain
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 8 minutes ago
Handshake Time/Retries....... 23 seconds/0
Non-linear Encoding, Rx/Tx... OFF/ON
Precoding, Rx/Tx............. OFF/ON
Shaping, Rx/Tx............... OFF/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 5
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 4,4
Last Rx/Tx State............. 67/87
Energy at 3750Hz/Average .... 73/15
Auto Gain Amplitude, db...... 15
Rx Level (Last/Min/Max), -dB. 20,1/20,1/20,1
Detection of 120 Hz Tones.... No
Detection of Dual PCM........ No
V.90 RBS Pattern............. 00
V.90 Alternating RBS Pattern. 00
V.90 Digital Pad Value, db... 0,0
V.90 Optimal Speed........... No Limit (Reg.S120=0)
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 03
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Server (Digital)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Unknown
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/65
Frames Errors, Rx/Tx......... 65/0 (0,4%/0,0%)
Frames Count, Rx/Tx.......... 18268/4931
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 1
Error Control Link NAKs...... 0
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 2 528 311
Characters Sent.............. 254 057
Average CPS, Rx/Tx........... 2686/269
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 64

[Technical Support]

Ну что же, вполне достойная статистика. Попробуйте такую строку:

S91=15 S210.7=1 S55.4=1 S17=64

Оставьте ту, с которой будет лучше работать.
_________________
Inpro
Technical Support

[softmaster]

Да у этой коробочки большой потенциал