Предыдущая тема :: Следующая тема |
Автор |
Сообщение |
Эдуард Associated member
Зарегистрирован: 09.12.2003 Сообщения: 7 Откуда: Ростов на Дону
|
Добавлено: Пн Июл 19, 2004 1:22 am Заголовок сообщения: IDC-IDC |
|
|
Здравствуйте.
Помогите, пожалуйста.
Два модема IDC - один на хорошей линии, другой на плохой.
Inpro IDC Modems Diagnostics, Version 1.0.1.31
10.07.2004 2:35:05 - Direct Log Write Entry
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.24
Time Online.................. 01:18:25
Termination Reason........... GSTN CLEARDOWN
Tx Rate (Last/Init/Min/Max).. 19200/31200/ 2400/31200 bps
Rx Rate (Last/Init/Min/Max).. 21600/33600/16800/33600 bps
Modulation................... V.34bis
Protocol/Compression......... NONE
Line Quality................. 12
Tx/Power Drop/Rx Level....... 15/0/22
SNR Last/Min/Max............. 43/43/43
Highest Rx/Tx State.......... 83/87
EQM Sum...................... 0012
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 1/17/1
Renegs Issued/Granted........ 21/84
FForwards/FBacks/Denied...... 10/11/0
Forced FB/FB after FF/MaxREJ. 0/1/0
Last dialed number........... T524675
Flex fail
Symbol Rate.................. 2400
Carrier Frequency Hz, Rx/Tx.. 1600/1600
EQM Value (Last/Min/Max)..... 12/2/127
EQM Hits..................... 0
EQM Last 10 Readings......... 12 12 13 13 12 14 13 12 12 12
Last Retrain/Reneg Status.... Remote Rate Renegotiation
Last Retrain/Reneg Reason.... Remote Rate Renegotiation
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 29 seconds/0
Non-linear Encoding, Rx/Tx... ON/ON
Precoding, Rx/Tx............. OFF/OFF
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 0
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 2,3
Last Rx/Tx State............. 83/83
Energy at 3750Hz/Average .... 288/802
Last AGC Gain Value.......... 80
Minimum AGC Gain Value....... 74
Maximum AGC Gain Value....... 81
Detection of 120 Hz Tones.... No
Detection of Dual PCM........ Yes
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/No/No/No/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. LR:T ODP:T
Frames REJected, Last/Total.. 0/0
Frames Count, Rx/Tx.......... 0/0
Error Control Frame Size..... NONE (0)
Error Control Timeouts....... 0
Error Control Link NAKs...... 0
Compression Dictionary Size.. NONE (0)
Characters Received.......... 1664167
Characters Sent.............. 1515487
Average CPS, Rx/Tx........... 353/322
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 65 |
|
Вернуться к началу |
|
|
Technical Support Expert
Зарегистрирован: 31.10.2002 Сообщения: 6330
|
Добавлено: Пн Июл 19, 2004 8:06 am Заголовок сообщения: |
|
|
Первое, что Вам нужно сделать - заставить модемы соединяться с коррекцией ошибок. Запретите им соединяться без коррекции (\N2 или \N4).
Второе: покажите статистику обеих модемов (или хотя бы того, который на плохой линии, оттуда виднее). _________________ Inpro
Technical Support |
|
Вернуться к началу |
|
|
Эдуард Associated member
Зарегистрирован: 09.12.2003 Сообщения: 7 Откуда: Ростов на Дону
|
Добавлено: Вт Авг 03, 2004 1:07 am Заголовок сообщения: |
|
|
Здравствуйте.
Сначала включить компрессию не удалось (невозможно установить соединение), затем установки модема IDC-2814BXL/VR+ были сброшены на заводские.
Статистика со стороны плохой линии, затем хорошей:
Inpro IDC Modems Diagnostics, Version 1.0.1.31
22.07.2004 1:17:12 - Direct Log Write Entry
--------------------------------------------------------
Modem type: IDC-2814BXL/VR+ (Plus) Firmware revision: V2.21
Time Online.................. 01:23:14
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 28800/28800/21600/28800 bps
Rx Rate (Last/Init/Min/Max).. 28800/28800/19200/28800 bps
Modulation................... V.34bis
Protocol/Compression......... NONE
Line Quality................. 17
Tx/Power Drop/Rx Level....... 9/0/22
SNR Last/Min/Max............. 43/41/43
Highest Rx/Tx State.......... 67/87
EQM Sum...................... 0017
Retrains Issued/Granted/Auto. 4/1/1
Renegs Issued/Granted........ 23/13
FForwards/FBacks/Denied...... 9/18/0
Forced FB/FB after FF/MaxREJ. 0/1/0
Symbol Rate.................. 3200
Carrier Frequency Hz, Rx/Tx.. 1829/1829
EQM Value (Last/Min/Max)..... 17/2/127
EQM Hits..................... 0
EQM Last 10 Readings......... 17 18 18 18 18 19 19 19 17 19
Last Retrain/Reneg Status.... Remote Retrain
Last Retrain/Reneg Reason.... Remote Retrain
Last Retrain/Reneg Time...... 6 minutes ago
Handshake Time/Retries....... 11 seconds/0
Non-linear Encoding, Rx/Tx... ON/ON
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 1
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 1,3
Last Rx/Tx State............. 67/67
Energy at 3750Hz/Average .... 56/237
Last AGC Gain Value.......... 83
Minimum AGC Gain Value....... 81
Maximum AGC Gain Value....... 88
Detection of 120 Hz Tones.... No
Detection of Dual PCM........ Yes
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Frames REJected, Last/Total.. 0/0
Frames Count, Rx/Tx.......... 0/0
Error Control Frame Size..... NONE (0)
Error Control Timeouts....... 0
Error Control Link NAKs...... 0
Compression Dictionary Size.. NONE (0)
Characters Received.......... 1740590
Characters Sent.............. 1635663
Average CPS, Rx/Tx........... 348/327
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 65
Inpro IDC Modems Diagnostics, Version 1.0.1.31
03.08.2004 1:07:09 - Direct Log Write Entry
--------------------------------------------------------
Modem type: IDC-2814BXL/VR+ (Plus) Firmware revision: V2.21
Time Online.................. 01:14:22
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 31200/33600/24000/33600 bps
Rx Rate (Last/Init/Min/Max).. 31200/33600/16800/33600 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 22
Tx/Power Drop/Rx Level....... 9/0/22
SNR Last/Min/Max............. 43/41/43
Highest Rx/Tx State.......... 85/87
EQM Sum...................... 001B
Retrains Issued/Granted/Auto. 3/3/0
Renegs Issued/Granted........ 22/30
FForwards/FBacks/Denied...... 15/8/0
Forced FB/FB after FF/MaxREJ. 1/1/8
Symbol Rate.................. 3429
Carrier Frequency Hz, Rx/Tx.. 1959/1959
EQM Value (Last/Min/Max)..... 22/3/127
EQM Hits..................... 0
EQM Last 10 Readings......... 23 24 22 21 22 22 23 23 24 34
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallforward due to Low EQM
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 11 seconds/0
Non-linear Encoding, Rx/Tx... ON/ON
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 0
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 1,7
Last Rx/Tx State............. 85/87
Energy at 3750Hz/Average .... 64/224
Last AGC Gain Value.......... 83
Minimum AGC Gain Value....... 82
Maximum AGC Gain Value....... 89
Detection of 120 Hz Tones.... No
Detection of Dual PCM........ Yes
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. ADP:T ADP:R ODP:R
Error Correction Status Byte. SYNC UA:T UA:R SAMBE:R XID:T XID:R
Frames REJected, Last/Total.. 1/133
Frames Errors, Rx/Tx......... 133/96 (0,4%/0,3%)
Frames Count, Rx/Tx.......... 34992/31266
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 37
Error Control Link NAKs...... 96
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 561362
Characters Sent.............. 653497
Average CPS, Rx/Tx........... 125/146
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 65
Inpro IDC Modems Diagnostics, Version 1.0.1.31
22.07.04 1:51:54 - Direct Log Write Entry
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.24
Time Online.................. 01:23:41
Termination Reason........... GSTN CLEARDOWN
Tx Rate (Last/Init/Min/Max).. 28800/28800/19200/28800 bps
Rx Rate (Last/Init/Min/Max).. 28800/28800/21600/28800 bps
Modulation................... V.34bis
Protocol/Compression......... NONE
Line Quality................. 12
Tx/Power Drop/Rx Level....... 9/2/24
SNR Last/Min/Max............. 43/43/43
Highest Rx/Tx State.......... 83/83
EQM Sum...................... 0018
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 1/4/1
Renegs Issued/Granted........ 14/23
FForwards/FBacks/Denied...... 2/13/0
Forced FB/FB after FF/MaxREJ. 0/1/0
Last dialed number........... T524675
Flex fail
Symbol Rate.................. 3200
Carrier Frequency Hz, Rx/Tx.. 1829/1829
EQM Value (Last/Min/Max)..... 12/5/127
EQM Hits..................... 0
EQM Last 10 Readings......... 19 19 18 19 20 19 19 19 19 18
Last Retrain/Reneg Status.... Remote Rate Renegotiation
Last Retrain/Reneg Reason.... Remote Rate Renegotiation
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 25 seconds/0
Non-linear Encoding, Rx/Tx... ON/ON
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 2
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 1,3
Last Rx/Tx State............. 83/83
Energy at 3750Hz/Average .... 349/844
Last AGC Gain Value.......... 79
Minimum AGC Gain Value....... 75
Maximum AGC Gain Value....... 80
Detection of 120 Hz Tones.... No
Detection of Dual PCM........ Yes
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/No/No/No/No
Remote supports Symbol Rates. 2800 3000(L)
Remote supports Symbol Rates. 3200(L) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. LR:T ODP:T
Frames REJected, Last/Total.. 0/0
Frames Count, Rx/Tx.......... 0/0
Error Control Frame Size..... NONE (0)
Error Control Timeouts....... 0
Error Control Link NAKs...... 0
Compression Dictionary Size.. NONE (0)
Characters Received.......... 1718004
Characters Sent.............. 1581308
Average CPS, Rx/Tx........... 342/314
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 67
Inpro IDC Modems Diagnostics, Version 1.0.1.31
03.08.04 1:13:32 - Direct Log Write Entry
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.24
Time Online.................. 01:14:45
Termination Reason........... LINK DISCONNECT
Tx Rate (Last/Init/Min/Max).. 31200/33600/16800/33600 bps
Rx Rate (Last/Init/Min/Max).. 31200/33600/24000/33600 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 35
Tx/Power Drop/Rx Level....... 9/2/24
SNR Last/Min/Max............. 43/43/43
Highest Rx/Tx State.......... 85/87
EQM Sum...................... 002F
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 3/3/0
Renegs Issued/Granted........ 31/22
FForwards/FBacks/Denied...... 16/16/0
Forced FB/FB after FF/MaxREJ. 0/3/5
Last dialed number........... T524675
Flex fail
Symbol Rate.................. 3429
Carrier Frequency Hz, Rx/Tx.. 1959/1959
EQM Value (Last/Min/Max)..... 35/6/127
EQM Hits..................... 0
EQM Last 10 Readings......... 38 34 33 38 35 35 37 33 35 42
Last Retrain/Reneg Status.... Remote Rate Renegotiation
Last Retrain/Reneg Reason.... Remote Rate Renegotiation
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 26 seconds/0
Non-linear Encoding, Rx/Tx... ON/ON
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 2
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 1,7
Last Rx/Tx State............. 67/87
Energy at 3750Hz/Average .... 170/99
Last AGC Gain Value.......... 79
Minimum AGC Gain Value....... 74
Maximum AGC Gain Value....... 79
Detection of 120 Hz Tones.... No
Detection of Dual PCM........ No
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/No/No/No/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:T UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/106
Frames Errors, Rx/Tx......... 106/116 (0,3%/0,3%)
Frames Count, Rx/Tx.......... 30605/36023
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 238
Error Control Link NAKs...... 116
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 653497
Characters Sent.............. 561379
Average CPS, Rx/Tx........... 145/125
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 67 |
|
Вернуться к началу |
|
|
Technical Support Expert
Зарегистрирован: 31.10.2002 Сообщения: 6330
|
Добавлено: Вт Авг 03, 2004 8:32 am Заголовок сообщения: |
|
|
Цитата: |
Сначала включить компрессию не удалось (невозможно установить соединение), затем установки модема IDC-2814BXL/VR+ были сброшены на заводские.
|
Расскажем, почему не удалось Посмотрите на первые статистики (где коррекции ошибок не было). Обратите внимание на то, что у отвечающего модема (статистики отвечающего приведены первыми) отсутствует строка:
Error Correction Status Byte. LR:T ODP:T
которая присутствует у вызывающего. Это значит, что у отвечающего модема протокол коррекции был запрещён (командой AT\N0). Естественно, если Вы пытались принудительно включить коррекцию ошибок у вызывающего модема, то соединение не устанавливалось вообще.
Чтобы "уйти от проблем", вызыванных неправильной расстановкой "галочек" в свойствах модема/соединения, пропишите в строку инициализации обеих модемов команду:
\N2
Кстати, неплохо было бы обновить микропрограмму в модемах. Ставьте опубликованный вчера пре-релиз версии 2.25.
После этого добавьте в строку инициализации команды:
\N2 S202.3=1 S91=12 S210.7=1 _________________ Inpro
Technical Support |
|
Вернуться к началу |
|
|
Эдуард Associated member
Зарегистрирован: 09.12.2003 Сообщения: 7 Откуда: Ростов на Дону
|
Добавлено: Пн Сен 20, 2004 2:51 am Заголовок сообщения: |
|
|
С прошивками 2.25 и строкой \N2 S202.3=1 S91=12 S210.7=1
Inpro IDC Modems Diagnostics, Version 1.0.1.31
20.09.2004 2:47:12 - Direct Log Write Entry
--------------------------------------------------------
Modem type: IDC-2814BXL/VR+ (Plus) Firmware revision: V2.25
Time Online.................. 01:57:46
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 33600/33600/16800/33600 bps
Rx Rate (Last/Init/Min/Max).. 33600/33600/ 7200/33600 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 56
Tx/Power Drop/Rx Level....... 9/1/28
SNR Last/Min/Max............. 34/34/37
Highest Rx/Tx State.......... 85/87
EQM Sum...................... 003A
Retrains Issued/Granted/Auto. 6/1/2
Renegs Issued/Granted........ 77/18
FForwards/FBacks/Denied...... 48/35/0
Forced FB/FB after FF/MaxREJ. 6/3/9
Last dialed number........... NA
Symbol Rate.................. 3429
Carrier Frequency Hz, Rx/Tx.. 1959/1959
EQM Value (Last/Min/Max)..... 56/0/127
EQM Hits..................... 0
EQM Last 10 Readings......... 62 61 59 61 52 52 54 56 55 54
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallforward due to Low EQM
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 11 seconds/0
Non-linear Encoding, Rx/Tx... OFF/ON
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 1
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 2,3
Last Rx/Tx State............. 67/87
Energy at 3750Hz/Average .... 138/591
Last AGC Gain Value.......... 67
Minimum AGC Gain Value....... 65
Maximum AGC Gain Value....... 70
Detection of 120 Hz Tones.... No
Detection of Dual PCM........ Yes
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/Yes/No/Yes/No/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... No
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. ADP:T ADP:R ODP:R
Error Correction Status Byte. SYNC UA:T UA:R SAMBE:R XID:T XID:R
Frames REJected, Last/Total.. 1/137
Frames Errors, Rx/Tx......... 393/89 (0,2%/0,0%)
Frames Count, Rx/Tx.......... 160679/266680
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 229
Error Control Link NAKs...... 89
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 7366776
Characters Sent.............. 13963916
Average CPS, Rx/Tx........... 1042/1976
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 62
Inpro IDC Modems Diagnostics, Version 1.0.1.31
20.09.04 2:46:33 - Direct Log Write Entry
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.25
Time Online.................. 01:59:07
Termination Reason........... LINK DISCONNECT
Tx Rate (Last/Init/Min/Max).. 33600/33600/ 7200/33600 bps
Rx Rate (Last/Init/Min/Max).. 33600/33600/16800/33600 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 35
Tx/Power Drop/Rx Level....... 12/0/24
SNR Last/Min/Max............. 43/43/43
Highest Rx/Tx State.......... 85/87
EQM Sum...................... 0011
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 1/6/2
Renegs Issued/Granted........ 19/76
FForwards/FBacks/Denied...... 8/11/0
Forced FB/FB after FF/MaxREJ. 0/0/4
Last dialed number........... T524675
Flex fail
Symbol Rate.................. 3429
Carrier Frequency Hz, Rx/Tx.. 1959/1959
EQM Value (Last/Min/Max)..... 35/2/127
EQM Hits..................... 0
EQM Last 10 Readings......... 36 35 32 37 38 34 40 31 33 34
Last Retrain/Reneg Status.... Remote Rate Renegotiation
Last Retrain/Reneg Reason.... Remote Rate Renegotiation
Last Retrain/Reneg Time...... 1 minutes ago
Handshake Time/Retries....... 20 seconds/0
Non-linear Encoding, Rx/Tx... ON/OFF
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 0
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 2,3
Last Rx/Tx State............. 67/87
Energy at 3750Hz/Average .... 314/892
Last AGC Gain Value.......... 78
Minimum AGC Gain Value....... 71
Maximum AGC Gain Value....... 82
Detection of 120 Hz Tones.... No
Detection of Dual PCM........ Yes
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:T UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/127
Frames Errors, Rx/Tx......... 127/381 (0,0%/0,2%)
Frames Count, Rx/Tx.......... 266005/163104
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 99
Error Control Link NAKs...... 125
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 13963916
Characters Sent.............. 7366776
Average CPS, Rx/Tx........... 1953/1030
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 67 |
|
Вернуться к началу |
|
|
Technical Support Expert
Зарегистрирован: 31.10.2002 Сообщения: 6330
|
Добавлено: Пн Сен 20, 2004 11:28 am Заголовок сообщения: |
|
|
Очевидно, Вы забыли прописать строку модему, который находился на плохой линии и был отвечающим:
Tx/Power Drop/Rx Level....... 9/1/28
Если бы модем проинициализировался командой S91=12 S210.7=1, то здесь стояло бы 12/0.
Но даже при таком раскладе Вы получили довольно неплохой результат, учитывая "качество" связи. _________________ Inpro
Technical Support |
|
Вернуться к началу |
|
|
Эдуард Associated member
Зарегистрирован: 09.12.2003 Сообщения: 7 Откуда: Ростов на Дону
|
Добавлено: Ср Сен 29, 2004 11:43 pm Заголовок сообщения: |
|
|
Здравствуйте.
Строку инициализации проверил, по словам владельца 2814-стоит(?!), оси win98, звонит 5614, отвечает 2814.
Попробуем ограничить скорость( играем в ИЛ2)
Inpro IDC Modems Diagnostics, Version 1.0.1.31
30.09.04 0:20:04 - Direct Log Write Entry
--------------------------------------------------------
Modem type: IDC-2814BXL/VR+ (Plus) Firmware revision: V2.25
Time Online.................. 00:55:57
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 28800/33600/ 9600/33600 bps
Rx Rate (Last/Init/Min/Max).. 24000/33600/ 9600/33600 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 31
Tx/Power Drop/Rx Level....... 9/1/24
SNR Last/Min/Max............. 39/36/41
Highest Rx/Tx State.......... 85/87
EQM Sum...................... 003B
Retrains Issued/Granted/Auto. 12/5/0
Renegs Issued/Granted........ 61/55
FForwards/FBacks/Denied...... 34/39/0
Forced FB/FB after FF/MaxREJ. 3/6/8
Last dialed number........... NA
Symbol Rate.................. 3429
Carrier Frequency Hz, Rx/Tx.. 1959/1959
EQM Value (Last/Min/Max)..... 31/0/127
EQM Hits..................... 0
EQM Last 10 Readings......... 18 18 18 18 19 18 17 16 20 18
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 10 seconds/0
Non-linear Encoding, Rx/Tx... OFF/ON
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 1
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 1,4
Last Rx/Tx State............. 85/87
Energy at 3750Hz/Average .... 130/503
Last AGC Gain Value.......... 79
Minimum AGC Gain Value....... 77
Maximum AGC Gain Value....... 81
Detection of 120 Hz Tones.... No
Detection of Dual PCM........ Yes
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... No
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. ADP:T ADP:R ODP:R
Error Correction Status Byte. SYNC UA:T UA:R SAMBE:R XID:T XID:R
Frames REJected, Last/Total.. 1/221
Frames Errors, Rx/Tx......... 221/234 (0,6%/0,3%)
Frames Count, Rx/Tx.......... 38654/67348
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 248
Error Control Link NAKs...... 234
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 2446715
Characters Sent.............. 3993046
Average CPS, Rx/Tx........... 728/1189
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 63
Inpro IDC Modems Diagnostics, Version 1.0.1.31
30.09.04 0:19:23 - Direct Log Write Entry
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.25
Time Online.................. 00:57:06
Termination Reason........... LINK DISCONNECT
Tx Rate (Last/Init/Min/Max).. 24000/33600/ 9600/33600 bps
Rx Rate (Last/Init/Min/Max).. 28800/33600/ 9600/33600 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 34
Tx/Power Drop/Rx Level....... 12/0/25
SNR Last/Min/Max............. 43/43/43
Highest Rx/Tx State.......... 85/87
EQM Sum...................... 0026
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 5/11/2
Renegs Issued/Granted........ 57/61
FForwards/FBacks/Denied...... 22/39/0
Forced FB/FB after FF/MaxREJ. 2/7/7
Last dialed number........... T524675
Flex fail
Symbol Rate.................. 3429
Carrier Frequency Hz, Rx/Tx.. 1959/1959
EQM Value (Last/Min/Max)..... 34/0/127
EQM Hits..................... 0
EQM Last 10 Readings......... 33 26 26 26 27 25 26 28 27 25
Last Retrain/Reneg Status.... Remote Rate Renegotiation
Last Retrain/Reneg Reason.... Remote Rate Renegotiation
Last Retrain/Reneg Time...... 1 minutes ago
Handshake Time/Retries....... 26 seconds/0
Non-linear Encoding, Rx/Tx... ON/OFF
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 3
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 1,4
Last Rx/Tx State............. 67/87
Energy at 3750Hz/Average .... 170/110
Last AGC Gain Value.......... 75
Minimum AGC Gain Value....... 62
Maximum AGC Gain Value....... 79
Detection of 120 Hz Tones.... No
Detection of Dual PCM........ No
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:T UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/252
Frames Errors, Rx/Tx......... 252/210 (0,4%/0,5%)
Frames Count, Rx/Tx.......... 66138/40871
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 74
Error Control Link NAKs...... 210
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 3993046
Characters Sent.............. 2446715
Average CPS, Rx/Tx........... 1165/714
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 68
Спасибо за помощь. |
|
Вернуться к началу |
|
|
Technical Support Expert
Зарегистрирован: 31.10.2002 Сообщения: 6330
|
Добавлено: Чт Сен 30, 2004 8:04 am Заголовок сообщения: |
|
|
Остаётся только повторить, что строка инициализации "доходит" только до IDC-5614BXL/VR+:
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.25
...
Tx/Power Drop/Rx Level....... 12/0/25
До IDC-2814BXL/VR+ она не доходит:
Modem type: IDC-2814BXL/VR+ (Plus) Firmware revision: V2.25
...
Tx/Power Drop/Rx Level....... 9/1/24
Специалистов по игрушке ИЛ2 у нас нет, поэтому Вам придётся разбираться самостоятельно. Неплохой способ - сравнить Ваши настройки в игрушке и в свойствах модема с настройками Вашего друга.
Что касается ограничения скорости - очень неплохая идея. Для работы игрушки вполне хватит 14400 бит/с. _________________ Inpro
Technical Support |
|
Вернуться к началу |
|
|
Эдуард Associated member
Зарегистрирован: 09.12.2003 Сообщения: 7 Откуда: Ростов на Дону
|
Добавлено: Пт Окт 01, 2004 9:41 pm Заголовок сообщения: |
|
|
Большое спасибо за помощь Technical Support |
|
Вернуться к началу |
|
|
|
|
Вы не можете начинать темы Вы не можете отвечать на сообщения Вы не можете редактировать свои сообщения Вы не можете удалять свои сообщения Вы не можете голосовать в опросах
|
Powered by phpBB © 2001, 2005 phpBB Group
|