Help Настроить IDC-5614BXL/VR

[Technical Support]

Записывать переговоры можно с помощью трёх программ. Кроме уже упомянутого ModemSpy, можно пользоваться IDC Ventafax и Phone Call Logger.

Поставьте для начала IDC Ventafax и попробуйте поработать с ней. Если проблемы останутся - подключите телефонный аппарат последовательно с модемом (т.е. в гнездо "Phone" модема) и отметьте этот факт соответствующей "галочкой" в настройках регистрации разговора в IDC Ventafax.
_________________
Inpro
Technical Support

[Alexander19]

Здравствуйте, подключился к новому провайдеру, чё посоветуете, данные без строки инициализации

Time Online.................. 00:53:59
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 26400/26400/24000/31200 bps
Rx Rate (Last/Init/Min/Max).. 36000/42667/33333/45333 bps
Modulation................... V.90
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 117
Tx/Power Drop/Rx Level....... 12/0/16
SNR Last/Min/Max............. 37/32/39
Highest Rx/Tx State.......... 67/67
EQM Sum...................... 00F0
RBS Pattern.................. 00
Rate Drop.................... 0
Digital Loss................. 2000
Retrains Issued/Granted/Auto. 26/0/10
Renegs Issued/Granted........ 30/2
FForwards/FBacks/Denied...... 20/36/0
Forced FB/FB after FF/MaxREJ. 0/5/4
Last dialed number........... P420377
V90 9481834347EB

Negotiation Result (Rx/Tx)... V.90 Issue 1 (asymmetric)/V.34
Symbol Rate (Rx/Tx).......... 8000/3200
Carrier Frequency Hz, Tx..... 1829
EQM Value (Last/Min/Max)..... 117/4/127
EQM Hits..................... 0
EQM Last 10 Readings......... 117 124 125 124 124 7 9 127 127 127
Last Retrain/Reneg Status.... Local Retrain
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 25 seconds/0
Non-linear Encoding, Rx/Tx... OFF/ON
Precoding, Rx/Tx............. OFF/ON
Shaping, Rx/Tx............... OFF/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 1
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 3,2
Last Rx/Tx State............. 67/67
Energy at 3750Hz/Average .... 3079/2071
Auto Gain Amplitude, db...... 10
AGC Gain (Last/Min/Max)...... 98/98/98
Detection of 120 Hz Tones.... Yes
Detection of Dual PCM........ No
V.90 RBS Pattern............. 00
V.90 Alternating RBS Pattern. 00
V.90 Digital Pad Value, db... 0,0
V.90 Optimal Speed........... 38667 bps (Reg.S120=9)
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 03
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Server (Digital)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Unknown
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/108
Frames Errors, Rx/Tx......... 108/21 (0,1%/0,1%)
Frames Count, Rx/Tx.......... 84808/16163
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 85
Error Control Link NAKs...... 21
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 10 781 678
Characters Sent.............. 298 617
Average CPS, Rx/Tx........... 3328/92
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 53

Какую стоку лучше прописать?

[Technical Support]

Попробуйте такую строку инициализации:

S91=15 S210.7=1 S120=0 +MS=,,,36000

и покажите, что получается. Желательно, чтобы сеанс длился хотя бы 10 минут.
_________________
Inpro
Technical Support

[Alexander19]

Inpro IDC Modems Diagnostics, Version 1.0.2.33
29.07.2004 21:10:12 - Outbound Call by RemoteAccess
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.25

Time Online.................. 00:12:48
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 24000/24000/24000/26400 bps
Rx Rate (Last/Init/Min/Max).. 33600/36000/28800/36000 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 42
Tx/Power Drop/Rx Level....... 15/0/16
SNR Last/Min/Max............. 39/37/39
Highest Rx/Tx State.......... 85/87
EQM Sum...................... 001C
RBS Pattern.................. 00
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 1/0/1
Renegs Issued/Granted........ 4/0
FForwards/FBacks/Denied...... 2/3/0
Forced FB/FB after FF/MaxREJ. 0/0/3
Last dialed number........... P420377
Flex fail 9481834347EB


Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 3429
Carrier Frequency Hz, Rx/Tx.. 1959/1959
EQM Value (Last/Min/Max)..... 42/10/127
EQM Hits..................... 0
EQM Last 10 Readings......... 41 43 42 45 39 42 41 45 41 37
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallforward due to Low EQM
Reason for V.34 Fallback..... Lowest PCM Speed, Prefer V.34
Last Retrain/Reneg Time...... 1 minutes ago
Handshake Time/Retries....... 25 seconds/0
Non-linear Encoding, Rx/Tx... ON/ON
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 2
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 3,5
Last Rx/Tx State............. 67/87
Energy at 3750Hz/Average .... 2557/1931
Auto Gain Amplitude, db...... 10
AGC Gain (Last/Min/Max)...... 97/96/98
Detection of 120 Hz Tones.... Yes
Detection of Dual PCM........ No
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 03
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Server (Digital)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Unknown
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/34
Frames Errors, Rx/Tx......... 34/4 (0,3%/0,1%)
Frames Count, Rx/Tx.......... 11952/4444
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 5
Error Control Link NAKs...... 4
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 1 764 726
Characters Sent.............. 253 894
Average CPS, Rx/Tx........... 2297/330
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 55

Вроде хуже стало, без строки чуть быстрей и скорость подключения быстрее (винда так пишет). Чё делать?

[Technical Support]

Попробуйте добавить в строку команду S17=64. Результирующая строка:

S91=15 S210.7=1 S17=64 S120=0 +MS=,,,36000

и ещё раз соберите статистику.
_________________
Inpro
Technical Support

[Alexander19]

Вот, совсем другое дело, тока меня смущает что винда скорость подключени со строкой пишет 36.0 кб/сек, а бес строки 42 кб/сек, хотя связь устойчевей сто процентов стала со строкой (дальний модем всегда откликается) и всё быстрей грузится! Пасибо стало на много лучше!!!!
Вот статистика
****************************
Inpro IDC Modems Diagnostics, Version 1.0.2.33
01.08.2004 6:26:25 - Outbound Call by RemoteAccess
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.25

Time Online.................. 00:12:05
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 24000/24000/24000/24000 bps
Rx Rate (Last/Init/Min/Max).. 36000/36000/36000/36000 bps
Modulation................... V.90
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 34
Tx/Power Drop/Rx Level....... 15/0/16
SNR Last/Min/Max............. 39/39/39
Highest Rx/Tx State.......... 67/67
EQM Sum...................... 00D5
RBS Pattern.................. 00
Rate Drop.................... 0
Digital Loss................. 2000
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 0/0
FForwards/FBacks/Denied...... 0/0/0
Forced FB/FB after FF/MaxREJ. 0/0/2
Last dialed number........... P420377
V90 9481834347EB


Negotiation Result (Rx/Tx)... V.90 Issue 1 (asymmetric)/V.34
Symbol Rate (Rx/Tx).......... 8000/3200
Carrier Frequency Hz, Tx..... 1829
EQM Value (Last/Min/Max)..... 34/10/39
EQM Hits..................... 0
EQM Last 10 Readings......... 33 33 35 33 32 31 38 35 30 34
Last Retrain/Reneg Status.... None
Last Retrain/Reneg Reason.... None
Last Retrain/Reneg Time...... 12 minutes ago
Handshake Time/Retries....... 25 seconds/0
Non-linear Encoding, Rx/Tx... OFF/ON
Precoding, Rx/Tx............. OFF/ON
Shaping, Rx/Tx............... OFF/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 0
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 3,2
Last Rx/Tx State............. 67/67
Energy at 3750Hz/Average .... 2874/2033
Auto Gain Amplitude, db...... 10
AGC Gain (Last/Min/Max)...... 98/98/98
Detection of 120 Hz Tones.... Yes
Detection of Dual PCM........ No
V.90 RBS Pattern............. 00
V.90 Alternating RBS Pattern. 00
V.90 Digital Pad Value, db... 0,0
V.90 Optimal Speed........... No Limit (Reg.S120=0)
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 03
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Server (Digital)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Unknown
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/2
Frames Errors, Rx/Tx......... 2/0 (0,0%/0,0%)
Frames Count, Rx/Tx.......... 18337/5834
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 2
Error Control Link NAKs...... 0
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 2 560 077
Characters Sent.............. 286 709
Average CPS, Rx/Tx........... 3531/395
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 55

Всё так и оставить?

[Technical Support]

Скорость стала 36000 бит/с потому, что она ограничена до 36000 бит/с командой +MS. На этой скорости модему удаётся избежать перетренировок, коих было множество в предыдущей статистике.

Было:

Time Online.................. 00:53:59
Retrains Issued/Granted/Auto. 26/0/10

Стало:

Time Online.................. 00:12:05
Retrains Issued/Granted/Auto. 0/0/0

Дождитесь начала рабочей недели (когда нагрузка на телефонную сеть возрастёт и помех станет больше). Если количество перетренировок не будет превышать 1 в 4-5 минут, то попробуйте "приподнять" ограничение (36000->37333->38667). Оставьте то значение, при котором удаётся избегать большого числа перетренировок.
_________________
Inpro
Technical Support