Что можно сделать в настройках соединения 2х компьюторов 1+1

[SWS]

Уважаемый суппорт!
Что можно сделать в настройках модема при соединения 2х компьюторов 1+1.

[Technical Support]

Вам нужно подробно изложить суть вопроса, указав при этом:

1. Тип или типы используемых модемов, версии микропрограммы.

2. Опрационную систему (или системы), установленные на каждом из компьютеров, их версии.

3. Тип телефонного соединения (коммутируемое или выделенная линия).

4. Дополнительные сведения, которые у Вас могут быть (например, "пробовал так, получилось то".
_________________
Inpro
Technical Support

[SWS]

Уважаемый Суппорт!

Значит так:

1. Тип модема №1 : IDC-5614BXL/VR+ (Plus)
версия микропрограммы: V2.25
DSP Type: RCV56DPF-PLL L8571A
DSP Revision: 43.07/43.07
Тип модема №2 : Зуксэл Омни (если надо точнее ... уточню)

2. Опрационная система №1 Windows 2000WS + SP4
Опрационная система №2 Windows xp (Home)

3. Тип телефонного Соединение - коммутируемое. (№1 -> №2)

4. Другая сторона (модем №2) копировала у меня файл (~5Mb, архив Rar) и не скопировала
буквально несколько процентов (вразумительного ответа почему несмоглая не получил.
ответ типа: "немогу скопировать файл ... ",
но соединение вроде бы не разрывалось!

Есть такая статистика соединения с моей стороны

1.-----------------------------------------------------------
Inpro IDC Modems Diagnostics, Version 1.0.2.33
09.02.2004 1:13:52 - Direct Log Write Entry
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.25

Time Online.................. 00:59:19
Termination Reason........... LINK DISCONNECT
Tx Rate (Last/Init/Min/Max).. 26400/28800/24000/31200 bps
Rx Rate (Last/Init/Min/Max).. 31200/33600/28800/33600 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/NONE
Line Quality................. 32
Tx/Power Drop/Rx Level....... 9/0/22
SNR Last/Min/Max............. 43/41/43
Highest Rx/Tx State.......... 85/87
EQM Sum...................... 001B
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/10/0
Renegs Issued/Granted........ 7/12
FForwards/FBacks/Denied...... 3/4/0
Forced FB/FB after FF/MaxREJ. 4/0/8
Last dialed number........... Pxxxxxx
Flex fail


Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 3429
Carrier Frequency Hz, Rx/Tx.. 1959/1959
EQM Value (Last/Min/Max)..... 32/15/127
EQM Hits..................... 0
EQM Last 10 Readings......... 37 24 37 31 30 48 55 45 56 38
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 44 seconds/0
Non-linear Encoding, Rx/Tx... ON/OFF
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 0
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 3,7
Last Rx/Tx State............. 85/87
Energy at 3750Hz/Average .... 141/66
AGC Gain (Last/Min/Max)...... 81/67/83
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Remote supports Symbol Rates. 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:T UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/233
Frames Errors, Rx/Tx......... 489/282 (6,4%/1,2%)
Frames Count, Rx/Tx.......... 7671/23921
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 102
Error Control Link NAKs...... 26
Compression Dictionary Size.. NONE (0)
Characters Received.......... 77 299
Characters Sent.............. 2 698 270
Average CPS, Rx/Tx........... 21/758
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 65


2.-----------------------------------------------------------
Modem Session Analyzer
-------------------------------------------------------------
Session time : 00:59:19
Retrains issued/granted/auto : 0/10/0
Renegs issued/granted/rrws : 7/12/0
TX Rate last/init : 26400/28800
RX Rate last/init : 31200/33600
Error control protocol/frame size : LAP-M/128
Average RX chars per frame : 10
TX frames/errors : 23921/282 (1.17 %)
RX frames/errors : 7671/489 (5.99 %)
Potential upstream cps : 3090
Potential downstream cps : 3450

DeviceName: IDC 5614BXL VR
UserInit:
----------------------------------------------------------------------
Time Online.................. 00:59:19
Termination Reason........... LINK DISCONNECT
Tx Rate (Last/Init/Min/Max).. 26400/28800/24000/31200 bps
Rx Rate (Last/Init/Min/Max).. 31200/33600/28800/33600 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/NONE
Line Quality................. 32
Tx/Power Drop/Rx Level....... 9/0/22
SNR Last/Min/Max............. 43/41/43
Highest Rx/Tx State.......... 85/87
EQM Sum...................... 001B
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/10/0
Renegs Issued/Granted........ 7/12
FForwards/FBacks/Denied...... 3/4/0
Forced FB/FB after FF/MaxREJ. 4/0/8
Last dialed number........... PХХХХХ
Flex fail

Rockwell Diagnostics/W32, version 1.3.0.0, compiled at Jun 13 2002 22:35:06
(c) 2000 Stanislav V. Mekhanoshin (rampitec@tu.spb.ru, 2:5030/172.9@fidonet)
----------------------------------------------------------------------------
Connection time : 00:59:19
Handshake Time/Retries : 44 sec/0
TX Rate (Last/Init/Min/Max) : 26400/28800/24000/31200
RX Rate (Last/Init/Min/Max) : 31200/33600/28800/33600
Modulation/Protocol/Compression : V.34/LAPM/NONE
TX Symbol rate : 3429
TX/RX carrier frequency, Hz : 1959/1959
Signal Level (TX/Power Drop), -dB : 9/0
RX Signal Level (Last/Min/Max), -dB : 22/27/21
Band Edge Lower/Upper, Hz : 150/3825
Round trip delay, ms : 3.749
EQM Value (Last/Min/Max/Negative) : 32/15/127/0
EQM Samples Running Sum : 001B
EQM Last 10 Readings : 37 24 37 31 30 48 55 45 56 38
SNR Ratio (Last/Min/Max), dB : 48/41/48
TX/RX Non-linear Encoding : OFF/ON
TX/RX Precoding : ON/ON
TX/RX Constellation Shaping : ON/ON
TX Trellis Encoding : 16 state
TX Pre-emphasis : 0
TX/RX state (Max TX/RX, Last TX/RX) : 87H/85H, 87H/85H
Error Correction Status : ODP:T ADP:R SABME:T UA:T,R XID:T,R SYNC
Energy at 3750Hz/Average Energy : 141/66
Retrains (Issued/Granted/Fast) : 0/10/0
Renegs (Issued/Granted) : 7/12
Retrans per frame/Frames rejected : 1/233
Total number of REJ sent/received : NA
Last Retrain/Reneg reason : Fall-back due to high EQM
Last Retrain/Reneg requested : Local Rate Renegotiation
Minutes Since Last Retrain/Reneg : 0
Disconnect reason : LINK DISCONNECT
Remote supports symbol rate (1,2,5) : 2743:OFF 2800:OFF 3429:ON 3429-TX:ON
Remote supports symbol rate (3,4) : 3000-L:ON 3000-H:ON 3200-L:ON 3200-H:ON
Remote power drop support : ON
Remote max symbol rate difference : 0 steps
Remote is a CME modem : No
Remote supports V.34bis : Yes
Remote frequency source : Internal
CRe/CRd/CL/MS/ACK/NAK received : No/No/No/No/No/No
V.8bis success/V.8bis neg started : No/Yes


Unimodem Diagnostics/W32, version 1.1.0.1, compiled at Nov 20 2002 22:29:58
(c) 2000 Stanislav V. Mekhanoshin (rampitec@tu.spb.ru, 2:5030/172.9@fidonet)
----------------------------------------------------------------------------
Diag Command Specification rev.: 1.0
Call Setup Result code : Data Answering signal detected
Multi-media mode : Data Only
DTE-DCE interface mode : Async data
TX/RX signal power level, -dBm : 9/22
Estimated noise level, -dBm : 65
TX/RX Negotiation : V.34/V.34
TX/RX Symbol Rate : 3429/3429
TX/RX Carrier frequency, Hz : 1959/1959
TX data rate (Last/Init) : 26400/28800
RX data rate (Last/Init) : 31200/33600
Temporary carrier loss count : 0
Carrier Rate Re-neg count : 19
Retrains Requested/Granted : 0/10
Protocol/Compression : V.42 LAPM/None
Error control frame size, bytes: 128
Error control timeouts in TX : 102
Error control NAKs received : 26
Compression dict. size, bytes : 0
TX/RX flow control : V.24 ckt 106/133 / V.24 ckt 106/133
TX/RX chars sent : 2698270/77299
TX/RX chars lost (data overrun): 0/0
TX/RX I-Frame count : 23921/7671
TX/RX I-Frame error count : 282/489
Termination Cause : Disconnect Frame Received


Connection : ххххх ххх
Time online : 00:59:10
Client IP address : 192.168.0.11
Server IP address : 192.168.0.10
PPP negotiation time : 8 sec
Authentication : CHAP
Multilink framing : No
Downstream compression : VJ PFC ACFC MPPC
Upstream compression : VJ PFC ACFC MPPC
Downstream encryption : None
Upstream encryption : None
Connection speed : 33600 bps
Bytes received : 166106 (at 47 B/sec)
Bytes transmitted : 2789798 (at 786 B/sec)
Inactive time : 00:37:16 (efficiency 37.0 %)
Active receive speed : 126 B/sec
Assumed cont-load recv speed : 122 B/sec
Frames received : 2602
Frames transmitted : 2656
CRC errors : 5
Timeout errors : 0
Alignment errors : 0
Hardware overruns : 0
Buffer overruns : 0
Framing errors : 0
Downstream compression ratio : 62 %
Upstream compression ratio : 4 %

[Technical Support]

Спасибо за подробное описание ситуации! В одном пункте, однако, Вы ошиблись:

"Тип модема №2 : Зуксэл Омни (если надо точнее ... уточню)"

ZyXEL Omni пользуются 64-позиционным кодированием, а в этой сессии было 16-позиционное. Значит, там точно не ZyXEL Omni:

Trellis Encoding, Tx......... 16 state

[SWS]

Уважаемый Суппорт! Здравствуйте.

Цитата:
>В одном пункте, однако, Вы ошиблись:
>>"Тип модема №2 : Зуксэл Омни (если надо точнее ... уточню)"

Со слов второй стороны у них модем точно
ZyXEL Omni 56K PCI (бирочка приклеена) :)
Драйвер версия: 2.0.1.0

Цитата:
>При этом, судя по статистике, собственно копирование шло
>примерно 22-25 минут, а дальше модемы просто стояли,
>ничего не передавалось.

Да, может быть... Я соединение установил и отлучился... ~ на часок :)
а когда вернулся в чате сообщение о неудачном копировании ...
после чего устоновили обратное соединение (№2->№1),
разбил файл на несколько частей по 1Мb
и тогда копирование прошло удачно. (этой статистики нет)

А вот статистика трех соединений
со строкой ини:S17=80 S202.3=1 \N5 %C0
после ~1:30 соединение разрывалось :(

1-Е СОЕДИНЕНИЕ

Modem Session Analyzer
-------------------------------------------------------------
Session time : 00:01:30
Retrains issued/granted/auto : 0/0/1
Renegs issued/granted/rrws : 1/0/0
TX Rate last/init : 31200/31200
RX Rate last/init : 28800/28800
Error control protocol/frame size : MNP/256
TX frames/errors : 0/0
RX frames/errors : 0/0
Potential upstream cps : 3209
Potential downstream cps : 2962

DeviceName: IDC 5614BXL VR
UserInit: S17=80 S202.3=1 \N5 %C0
----------------------------------------------------------------------
Time Online.................. 00:01:30
Termination Reason........... RETRAIN FAILURE
Tx Rate (Last/Init/Min/Max).. 31200/31200/31200/31200 bps
Rx Rate (Last/Init/Min/Max).. 28800/28800/28800/28800 bps
Modulation................... V.34bis
Protocol/Compression......... MNP/NONE
Line Quality................. 125
Tx/Power Drop/Rx Level....... 9/0/NA
SNR Last/Min/Max............. 41/41/41
Highest Rx/Tx State.......... 67/84
EQM Sum...................... 0088
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/1
Renegs Issued/Granted........ 1/0
FForwards/FBacks/Denied...... 0/1/0
Forced FB/FB after FF/MaxREJ. 0/0/0
Last dialed number........... PХХХХХ
Flex fail

Rockwell Diagnostics/W32, version 1.3.0.0, compiled at Jun 13 2002 22:35:06
(c) 2000 Stanislav V. Mekhanoshin (rampitec@tu.spb.ru, 2:5030/172.9@fidonet)
----------------------------------------------------------------------------
Connection time : 00:01:30
Handshake Time/Retries : 30 sec/0
TX Rate (Last/Init/Min/Max) : 31200/31200/31200/31200
RX Rate (Last/Init/Min/Max) : 28800/28800/28800/28800
Modulation/Protocol/Compression : V.34/MNP4/NONE
TX Symbol rate : 3429
TX/RX carrier frequency, Hz : 1959/1959
Signal Level (TX/Power Drop), -dB : 9/0
RX Signal Level (Last/Min/Max), -dB : NA/43/16
Band Edge Lower/Upper, Hz : 150/3825
Round trip delay, ms : 3.749
EQM Value (Last/Min/Max/Negative) : 125/27/127/0
EQM Samples Running Sum : 0088
EQM Last 10 Readings : 126 126 125 125 106 106 39 42 49 40
SNR Ratio (Last/Min/Max), dB : 41/41/41
TX/RX Non-linear Encoding : OFF/ON
TX/RX Precoding : ON/ON
TX/RX Constellation Shaping : ON/ON
TX Trellis Encoding : 16 state
TX Pre-emphasis : 0
TX/RX state (Max TX/RX, Last TX/RX) : 84H/67H, 20H/22H
Error Correction Status : LR:T,R LA:T,R
Energy at 3750Hz/Average Energy : 552/301
Retrains (Issued/Granted/Fast) : 0/0/0
Renegs (Issued/Granted) : 1/0
Retrans per frame/Frames rejected : 0/0
Total number of REJ sent/received : 0/0
Last Retrain/Reneg reason : Fall-back due to high EQM
Last Retrain/Reneg requested : Local Rate Renegotiation
Minutes Since Last Retrain/Reneg : 0
Disconnect reason : RETRAIN FAILURE
Remote supports symbol rate (1,2,5) : 2743:OFF 2800:OFF 3429:ON 3429-TX:ON
Remote supports symbol rate (3,4) : 3000-L:ON 3000-H:ON 3200-L:ON 3200-H:ON
Remote power drop support : ON
Remote max symbol rate difference : 0 steps
Remote is a CME modem : No
Remote supports V.34bis : Yes
Remote frequency source : Internal
CRe/CRd/CL/MS/ACK/NAK received : No/No/No/No/No/No
V.8bis success/V.8bis neg started : No/Yes
Workaround used : ABCODE check (machine-gun noise WA)


Unimodem Diagnostics/W32, version 1.1.0.1, compiled at Nov 20 2002 22:29:58
(c) 2000 Stanislav V. Mekhanoshin (rampitec@tu.spb.ru, 2:5030/172.9@fidonet)
----------------------------------------------------------------------------
Diag Command Specification rev.: 1.0
Call Setup Result code : Data Answering signal detected
Multi-media mode : Data Only
DTE-DCE interface mode : Async data
TX/RX signal power level, -dBm : 9/47
Estimated noise level, -dBm : 93
TX/RX Negotiation : V.34/V.34
TX/RX Symbol Rate : 3429/3429
TX/RX Carrier frequency, Hz : 1959/1959
TX data rate (Last/Init) : 31200/31200
RX data rate (Last/Init) : 28800/28800
Temporary carrier loss count : 0
Carrier Rate Re-neg count : 1
Retrains Requested/Granted : 0/0
Protocol/Compression : V.42 Alternative protocol (MNPT)/None
Error control frame size, bytes: 256
Error control timeouts in TX : 0
Error control NAKs received : 0
Compression dict. size, bytes : 0
TX/RX flow control : V.24 ckt 106/133 / V.24 ckt 106/133
TX/RX chars sent : 2476/1267
TX/RX chars lost (data overrun): 0/0
TX/RX I-Frame count : 0/0
TX/RX I-Frame error count : 0/0
Termination Cause : Retrain Failed


Connection : ХХХХХ ХХХ
Time online : 00:01:19
Client IP address : 192.168.0.11
Server IP address : 192.168.0.10
PPP negotiation time : 9 sec
Authentication : CHAP
Multilink framing : No
Downstream compression : PFC ACFC MPPC
Upstream compression : PFC ACFC MPPC
Downstream encryption : None
Upstream encryption : None
Connection speed : 28800 bps
Bytes received : 1790 (at 23 B/sec)
Bytes transmitted : 6990 (at 88 B/sec)
Inactive time : 00:01:13 (efficiency 7.2 %)
Active receive speed : NA
Assumed cont-load recv speed : NA
Frames received : 24
Frames transmitted : 55
CRC errors : 0
Timeout errors : 0
Alignment errors : 0
Hardware overruns : 0
Buffer overruns : 0
Framing errors : 0
Downstream compression ratio : 41 %
Upstream compression ratio : 70 %



-------------------------------------------------------------
2-Е СОЕДИНЕНИЕ

Modem Session Analyzer
-------------------------------------------------------------
Session time : 00:01:27
Retrains issued/granted/auto : 0/0/1
Renegs issued/granted/rrws : 1/0/0
TX Rate last/init : 28800/28800
RX Rate last/init : 33600/33600
Error control protocol/frame size : MNP/256
TX frames/errors : 0/0
RX frames/errors : 0/0
Potential upstream cps : 2944
Potential downstream cps : 3435

DeviceName: IDC 5614BXL VR
UserInit: S17=80 S202.3=1 \N5 %C0
----------------------------------------------------------------------
Time Online.................. 00:01:27
Termination Reason........... RETRAIN FAILURE
Tx Rate (Last/Init/Min/Max).. 28800/28800/28800/28800 bps
Rx Rate (Last/Init/Min/Max).. 33600/33600/33600/33600 bps
Modulation................... V.34bis
Protocol/Compression......... MNP/NONE
Line Quality................. 127
Tx/Power Drop/Rx Level....... 9/0/NA
SNR Last/Min/Max............. 43/43/43
Highest Rx/Tx State.......... 67/84
EQM Sum...................... 003E
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/1
Renegs Issued/Granted........ 1/0
FForwards/FBacks/Denied...... 0/1/0
Forced FB/FB after FF/MaxREJ. 0/0/0
Last dialed number........... PХХХХХ
Flex fail

Rockwell Diagnostics/W32, version 1.3.0.0, compiled at Jun 13 2002 22:35:06
(c) 2000 Stanislav V. Mekhanoshin (rampitec@tu.spb.ru, 2:5030/172.9@fidonet)
----------------------------------------------------------------------------
Connection time : 00:01:27
Handshake Time/Retries : 25 sec/0
TX Rate (Last/Init/Min/Max) : 28800/28800/28800/28800
RX Rate (Last/Init/Min/Max) : 33600/33600/33600/33600
Modulation/Protocol/Compression : V.34/MNP4/NONE
TX Symbol rate : 3429
TX/RX carrier frequency, Hz : 1959/1959
Signal Level (TX/Power Drop), -dB : 9/0
RX Signal Level (Last/Min/Max), -dB : NA/45/15
Band Edge Lower/Upper, Hz : 150/3825
Round trip delay, ms : 3.749
EQM Value (Last/Min/Max/Negative) : 127/41/127/0
EQM Samples Running Sum : 003E
EQM Last 10 Readings : 127 127 127 127 124 124 58 61 58 63
SNR Ratio (Last/Min/Max), dB : 48/48/48
TX/RX Non-linear Encoding : OFF/ON
TX/RX Precoding : ON/ON
TX/RX Constellation Shaping : ON/ON
TX Trellis Encoding : 16 state
TX Pre-emphasis : 0
TX/RX state (Max TX/RX, Last TX/RX) : 84H/67H, 20H/22H
Error Correction Status : LR:T,R LA:T,R
Energy at 3750Hz/Average Energy : 101/65
Retrains (Issued/Granted/Fast) : 0/0/0
Renegs (Issued/Granted) : 1/0
Retrans per frame/Frames rejected : 0/0
Total number of REJ sent/received : 0/0
Last Retrain/Reneg reason : Fall-back due to high EQM
Last Retrain/Reneg requested : Local Rate Renegotiation
Minutes Since Last Retrain/Reneg : 0
Disconnect reason : RETRAIN FAILURE
Remote supports symbol rate (1,2,5) : 2743:OFF 2800:OFF 3429:ON 3429-TX:ON
Remote supports symbol rate (3,4) : 3000-L:ON 3000-H:ON 3200-L:ON 3200-H:ON
Remote power drop support : ON
Remote max symbol rate difference : 0 steps
Remote is a CME modem : No
Remote supports V.34bis : Yes
Remote frequency source : Internal
CRe/CRd/CL/MS/ACK/NAK received : No/No/No/No/No/No
V.8bis success/V.8bis neg started : No/Yes
Workaround used : ABCODE check (machine-gun noise WA)


Unimodem Diagnostics/W32, version 1.1.0.1, compiled at Nov 20 2002 22:29:58
(c) 2000 Stanislav V. Mekhanoshin (rampitec@tu.spb.ru, 2:5030/172.9@fidonet)
----------------------------------------------------------------------------
Diag Command Specification rev.: 1.0
Call Setup Result code : Data Answering signal detected
Multi-media mode : Data Only
DTE-DCE interface mode : Async data
TX/RX signal power level, -dBm : 9/47
Estimated noise level, -dBm : 95
TX/RX Negotiation : V.34/V.34
TX/RX Symbol Rate : 3429/3429
TX/RX Carrier frequency, Hz : 1959/1959
TX data rate (Last/Init) : 28800/28800
RX data rate (Last/Init) : 33600/33600
Temporary carrier loss count : 0
Carrier Rate Re-neg count : 1
Retrains Requested/Granted : 0/0
Protocol/Compression : V.42 Alternative protocol (MNPT)/None
Error control frame size, bytes: 256
Error control timeouts in TX : 0
Error control NAKs received : 0
Compression dict. size, bytes : 0
TX/RX flow control : V.24 ckt 106/133 / V.24 ckt 106/133
TX/RX chars sent : 2278/599
TX/RX chars lost (data overrun): 0/564
TX/RX I-Frame count : 0/0
TX/RX I-Frame error count : 0/0
Termination Cause : Retrain Failed


Connection : ХХХХХ ХХХ
Time online : 00:01:16
Client IP address : 192.168.0.11
Server IP address : 192.168.0.10
PPP negotiation time : 8 sec
Authentication : CHAP
Multilink framing : No
Downstream compression : PFC ACFC MPPC
Upstream compression : PFC ACFC MPPC
Downstream encryption : None
Upstream encryption : None
Connection speed : 33600 bps
Bytes received : 531 (at 7 B/sec)
Bytes transmitted : 6620 (at 87 B/sec)
Inactive time : 00:01:14 (efficiency 2.2 %)
Active receive speed : NA
Assumed cont-load recv speed : NA
Frames received : 15
Frames transmitted : 68
CRC errors : 0
Timeout errors : 0
Alignment errors : 0
Hardware overruns : 0
Buffer overruns : 0
Framing errors : 0
Downstream compression ratio : 14 %
Upstream compression ratio : 71 %



------------------------------------------------------------
3-Е СОЕДИНЕНИЕ

Modem Session Analyzer
-------------------------------------------------------------
Session time : 00:01:45
Retrains issued/granted/auto : 0/0/1
Renegs issued/granted/rrws : 1/0/0
TX Rate last/init : 31200/31200
RX Rate last/init : 31200/31200
Error control protocol/frame size : MNP/256
TX frames/errors : 0/0
RX frames/errors : 0/0
Potential upstream cps : 3286
Potential downstream cps : 3286

DeviceName: IDC 5614BXL VR
UserInit: S17=80 S202.3=1 \N5 %C0
----------------------------------------------------------------------
Time Online.................. 00:01:45
Termination Reason........... RETRAIN FAILURE
Tx Rate (Last/Init/Min/Max).. 31200/31200/31200/31200 bps
Rx Rate (Last/Init/Min/Max).. 31200/31200/31200/31200 bps
Modulation................... V.34bis
Protocol/Compression......... MNP/NONE
Line Quality................. 126
Tx/Power Drop/Rx Level....... 9/0/NA
SNR Last/Min/Max............. 43/43/43
Highest Rx/Tx State.......... 67/84
EQM Sum...................... 004E
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/1
Renegs Issued/Granted........ 1/0
FForwards/FBacks/Denied...... 0/1/0
Forced FB/FB after FF/MaxREJ. 0/0/0
Last dialed number........... Pxxxxx
Flex fail

Rockwell Diagnostics/W32, version 1.3.0.0, compiled at Jun 13 2002 22:35:06
(c) 2000 Stanislav V. Mekhanoshin (rampitec@tu.spb.ru, 2:5030/172.9@fidonet)
----------------------------------------------------------------------------
Connection time : 00:01:45
Handshake Time/Retries : 29 sec/0
TX Rate (Last/Init/Min/Max) : 31200/31200/31200/31200
RX Rate (Last/Init/Min/Max) : 31200/31200/31200/31200
Modulation/Protocol/Compression : V.34/MNP4/NONE
TX Symbol rate : 3429
TX/RX carrier frequency, Hz : 1959/1959
Signal Level (TX/Power Drop), -dB : 9/0
RX Signal Level (Last/Min/Max), -dB : NA/45/15
Band Edge Lower/Upper, Hz : 150/3825
Round trip delay, ms : 3.749
EQM Value (Last/Min/Max/Negative) : 126/32/127/0
EQM Samples Running Sum : 004E
EQM Last 10 Readings : 126 126 126 126 127 127 39 40 40 36
SNR Ratio (Last/Min/Max), dB : 48/48/48
TX/RX Non-linear Encoding : OFF/ON
TX/RX Precoding : ON/ON
TX/RX Constellation Shaping : ON/ON
TX Trellis Encoding : 16 state
TX Pre-emphasis : 0
TX/RX state (Max TX/RX, Last TX/RX) : 84H/67H, 20H/22H
Error Correction Status : LR:T,R LA:T,R
Energy at 3750Hz/Average Energy : 113/69
Retrains (Issued/Granted/Fast) : 0/0/0
Renegs (Issued/Granted) : 1/0
Retrans per frame/Frames rejected : 0/0
Total number of REJ sent/received : 0/0
Last Retrain/Reneg reason : Fall-back due to high EQM
Last Retrain/Reneg requested : Local Rate Renegotiation
Minutes Since Last Retrain/Reneg : 0
Disconnect reason : RETRAIN FAILURE
Remote supports symbol rate (1,2,5) : 2743:OFF 2800:OFF 3429:ON 3429-TX:ON
Remote supports symbol rate (3,4) : 3000-L:ON 3000-H:ON 3200-L:ON 3200-H:ON
Remote power drop support : ON
Remote max symbol rate difference : 0 steps
Remote is a CME modem : No
Remote supports V.34bis : Yes
Remote frequency source : Internal
CRe/CRd/CL/MS/ACK/NAK received : No/No/No/No/No/No
V.8bis success/V.8bis neg started : No/Yes
Workaround used : ABCODE check (machine-gun noise WA)

Unimodem Diagnostics/W32, version 1.1.0.1, compiled at Nov 20 2002 22:29:58
(c) 2000 Stanislav V. Mekhanoshin (rampitec@tu.spb.ru, 2:5030/172.9@fidonet)
----------------------------------------------------------------------------
Diag Command Specification rev.: 1.0
Call Setup Result code : Data Answering signal detected
Multi-media mode : Data Only
DTE-DCE interface mode : Async data
TX/RX signal power level, -dBm : 9/47
Estimated noise level, -dBm : 95
TX/RX Negotiation : V.34/V.34
TX/RX Symbol Rate : 3429/3429
TX/RX Carrier frequency, Hz : 1959/1959
TX data rate (Last/Init) : 31200/31200
RX data rate (Last/Init) : 31200/31200
Temporary carrier loss count : 0
Carrier Rate Re-neg count : 1
Retrains Requested/Granted : 0/0
Protocol/Compression : V.42 Alternative protocol (MNPT)/None
Error control frame size, bytes: 256
Error control timeouts in TX : 0
Error control NAKs received : 0
Compression dict. size, bytes : 0
TX/RX flow control : V.24 ckt 106/133 / V.24 ckt 106/133
TX/RX chars sent : 2650/1558
TX/RX chars lost (data overrun): 0/0
TX/RX I-Frame count : 0/0
TX/RX I-Frame error count : 0/0
Termination Cause : Retrain Failed

Connection : ХХХХХ ХХХ
Time online : 00:01:32
Client IP address : 192.168.0.12
Server IP address : 192.168.0.10
PPP negotiation time : 10 sec
Authentication : CHAP
Multilink framing : No
Downstream compression : PFC ACFC MPPC
Upstream compression : PFC ACFC MPPC
Downstream encryption : None
Upstream encryption : None
Connection speed : 31200 bps
Bytes received : 2415 (at 26 B/sec)
Bytes transmitted : 7517 (at 81 B/sec)
Inactive time : 00:01:15 (efficiency 18.5 %)
Active receive speed : NA
Assumed cont-load recv speed : NA
Frames received : 38
Frames transmitted : 76
CRC errors : 0
Timeout errors : 0
Alignment errors : 0
Hardware overruns : 0
Buffer overruns : 0
Framing errors : 0
Downstream compression ratio : 47 %
Upstream compression ratio : 70 %

[Technical Support]

[SWS]

Уважемый Суппорт! Здравствуйте!

Цытата:
>Придётся Вам убрать \N5 %C0 из строки инициализации.
убрал...

еще... вторая сторона установила ОС ХР prof
модем не определился как ZyXEL Omni 56K PCI
оставили как опредилился ...
соединились, копировали архив ~13Мб , все ОК
Вот статистика...
Можно ли что улучшить? Или оставить как есть?
Если можно ... прокомментируйте.


Time Online.................. 01:38:44
Termination Reason........... LINK DISCONNECT
Tx Rate (Last/Init/Min/Max).. 24000/28800/16800/28800 bps
Rx Rate (Last/Init/Min/Max).. 26400/31200/24000/31200 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/NONE
Line Quality................. 38
Tx/Power Drop/Rx Level....... 9/0/27
SNR Last/Min/Max............. 41/41/43
Highest Rx/Tx State.......... 85/87
EQM Sum...................... 0074
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/1/0
Renegs Issued/Granted........ 4/11
FForwards/FBacks/Denied...... 0/4/0
Forced FB/FB after FF/MaxREJ. 3/0/8
Last dialed number........... Tхххххх
Flex fail 948E81A1


Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 3429
Carrier Frequency Hz, Rx/Tx.. 1959/1959
EQM Value (Last/Min/Max)..... 38/8/127
EQM Hits..................... 0
EQM Last 10 Readings......... 30 38 32 30 44 35 32 30 36 45
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 51 minutes ago
Handshake Time/Retries....... 12 seconds/0
Non-linear Encoding, Rx/Tx... ON/OFF
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 0
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 4,3
Last Rx/Tx State............. 85/87
Energy at 3750Hz/Average .... 424/313
AGC Gain (Last/Min/Max)...... 71/70/79
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/Yes/No/No/No/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell based
Remote Protocol Support...... K56flex
Remote K56flex Version....... 01
Remote K56flex Capabilities.. Prototype mode supported
Remote Type.................. Client (Analog)
Remote supports Symbol Rates. 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. ADP:T ADP:R ODP:R
Error Correction Status Byte. SYNC UA:T SAMBE:R XID:T XID:R
Frames REJected, Last/Total.. 1/223
Frames Errors, Rx/Tx......... 1247/480 (7,9%/0,4%)
Frames Count, Rx/Tx.......... 15834/113874
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 48
Error Control Link NAKs...... 224
Compression Dictionary Size.. NONE (0)
Characters Received.......... 270 260
Characters Sent.............. 14 055 321
Average CPS, Rx/Tx........... 45/2372
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 68


Rockwell Diagnostics/W32, version 1.3.0.0, compiled at Jun 13 2002 22:35:06
(c) 2000 Stanislav V. Mekhanoshin (rampitec@tu.spb.ru, 2:5030/172.9@fidonet)
----------------------------------------------------------------------------
Connection time : 01:38:44
Handshake Time/Retries : 12 sec/0
TX Rate (Last/Init/Min/Max) : 24000/28800/16800/28800
RX Rate (Last/Init/Min/Max) : 26400/31200/24000/31200
Modulation/Protocol/Compression : V.34/LAPM/NONE
TX Symbol rate : 3429
TX/RX carrier frequency, Hz : 1959/1959
Signal Level (TX/Power Drop), -dB : 9/0
RX Signal Level (Last/Min/Max), -dB : 25/26/22
Band Edge Lower/Upper, Hz : 150/3825
Round trip delay, ms : 4.333
EQM Value (Last/Min/Max/Negative) : 38/8/127/0
EQM Samples Running Sum : 0074
EQM Last 10 Readings : 30 38 32 30 44 35 32 30 36 45
SNR Ratio (Last/Min/Max), dB : 41/41/49
TX/RX Non-linear Encoding : OFF/ON
TX/RX Precoding : ON/ON
TX/RX Constellation Shaping : ON/ON
TX Trellis Encoding : 16 state
TX Pre-emphasis : 0
TX/RX state (Max TX/RX, Last TX/RX) : 87H/85H, 87H/85H
Error Correction Status : ODP:R ADP:T,R SABME:R UA:T XID:T,R SYNC
Energy at 3750Hz/Average Energy : 424/313
Retrains (Issued/Granted/Fast) : 0/1/0
Renegs (Issued/Granted) : 4/11
Retrans per frame/Frames rejected : 1/223
Total number of REJ sent/received : NA
Last Retrain/Reneg reason : Fall-back due to high EQM
Last Retrain/Reneg requested : Local Rate Renegotiation
Minutes Since Last Retrain/Reneg : 51
Disconnect reason : LINK DISCONNECT
Remote Manufacturer/Licensee Code : Conexant/#142
Remote Manufacturer's Product Caps : K56Flex
Remote V.8bis caps (type) : Analog (Client)
Remote V.8bis caps (K56Flex mode) : K56Flex prototype mode supported
Remote V.8bis caps (K56Flex version): 1.0
Remote supports symbol rate (1,2,5) : 2743:OFF 2800:OFF 3429:ON 3429-TX:ON
Remote supports symbol rate (3,4) : 3000-L:ON 3000-H:ON 3200-L:ON 3200-H:ON
Remote power drop support : ON
Remote max symbol rate difference : 0 steps
Remote is a CME modem : No
Remote supports V.34bis : Yes
Remote frequency source : Internal
CRe/CRd/CL/MS/ACK/NAK received : No/Yes/No/No/No/No
V.8bis success/V.8bis neg started : No/Yes


Unimodem Diagnostics/W32, version 1.1.0.1, compiled at Nov 20 2002 22:29:58
(c) 2000 Stanislav V. Mekhanoshin (rampitec@tu.spb.ru, 2:5030/172.9@fidonet)
----------------------------------------------------------------------------
Diag Command Specification rev.: 1.0
Call Setup Result code : V.8bis signal detected
Multi-media mode : Data Only
DTE-DCE interface mode : Async data
TX/RX signal power level, -dBm : 9/27
Estimated noise level, -dBm : 68
TX/RX Negotiation : V.34/V.34
TX/RX Symbol Rate : 3429/3429
TX/RX Carrier frequency, Hz : 1959/1959
TX data rate (Last/Init) : 24000/28800
RX data rate (Last/Init) : 26400/31200
Temporary carrier loss count : 0
Carrier Rate Re-neg count : 15
Retrains Requested/Granted : 0/1
Protocol/Compression : V.42 LAPM/None
Error control frame size, bytes: 128
Error control timeouts in TX : 48
Error control NAKs received : 224
Compression dict. size, bytes : 0
TX/RX flow control : V.24 ckt 106/133 / V.24 ckt 106/133
TX/RX chars sent : 14055321/270260
TX/RX chars lost (data overrun): 0/0
TX/RX I-Frame count : 113874/15834
TX/RX I-Frame error count : 480/1247
Termination Cause : Disconnect Frame Received

[Technical Support]

[SWS]

Уважаемый Суппорт! Здравствуйте.

Цитата:
>лучше снизить скорость приёма за счёт увеличения
S17 (снижения агрессивности модема). Поставьте S17=250.

Поставил. Все работало гладко, меня устраивает (статистику правда забыл сохранить, каюсь...)
(копировали фал ~9,5 Mb / час) Но,...

Если я правильно понял, мой модем настроен на передачу данных.
А если мне надо принимать (копировать файл)... надо ли что менять в настройках моего
и удаленного модема?

Есть статистика соединения (с пустой стр.иниц.),
когда я копировал файл ~13Mb (скопировать не удалось,связь при этом не разрывалась)


Time Online.................. 00:52:02
Termination Reason........... LINK DISCONNECT
Tx Rate (Last/Init/Min/Max).. 26400/28800/14400/31200 bps
Rx Rate (Last/Init/Min/Max).. 19200/28800/ 9600/28800 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 4
Tx/Power Drop/Rx Level....... 9/0/24
SNR Last/Min/Max............. 43/34/43
Highest Rx/Tx State.......... 85/87
EQM Sum...................... 00BB
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 3/0/0
Renegs Issued/Granted........ 33/15
FForwards/FBacks/Denied...... 9/27/0
Forced FB/FB after FF/MaxREJ. 27/3/11
Last dialed number........... Tхххххх
Flex fail

Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 3429
Carrier Frequency Hz, Rx/Tx.. 1959/1959
EQM Value (Last/Min/Max)..... 4/0/41
EQM Hits..................... 0
EQM Last 10 Readings......... 4 8 9 9 14 8 6 3 3 2
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 2 minutes ago
Handshake Time/Retries....... 24 seconds/0
Non-linear Encoding, Rx/Tx... OFF/OFF
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 0
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 3,7
Last Rx/Tx State............. 85/87
Energy at 3750Hz/Average .... 131/71
AGC Gain (Last/Min/Max)...... 79/72/83
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Remote supports Symbol Rates. 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:T UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/142
Frames Errors, Rx/Tx......... 1422/36 (4,6%/0,7%)
Frames Count, Rx/Tx.......... 30734/4958
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 38
Error Control Link NAKs...... 36
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 2 051 539
Characters Sent.............. 141 447
Average CPS, Rx/Tx........... 657/45
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 67

[SWS]

А где суппорт?

[Peter Stoliarov]

Неизвестно
Вроде они говорили, что в 2004 году Инпро собирается обновить модельный ряд. Видимо, заняты подготовкой к выпуску новых модемов.

[Technical Support]

[Oxy]

2 Technical Support

[Michael Kiselev]

[Oxy]

Спасибо, теперь понятно