Первый модем! Помогите оптимизировать, пожалуйста.

[tias]

Купил пару дней назад модем IDC-5614BXL/VR+.
Статистика собрана с помощью:
"Утилита IDC Modems Diagnostics, версия 1.0.1.31 от 13 июля 2003 г."

Строка инициализации:
"AT+MS=11,,,,,,33600"

Чем сможете помочь:
Inpro IDC Modems Diagnostics, Version 1.0.1.31
11.09.2003 14:53:53 - Direct Log Write Entry
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.23

Time Online.................. 02:00:16
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 21600/28800/19200/31200 bps
Rx Rate (Last/Init/Min/Max).. 33600/33600/26400/33600 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 127
Tx/Power Drop/Rx Level....... 9/0/39
SNR Last/Min/Max............. 39/39/39
Highest Rx/Tx State.......... 84/87
EQM Sum...................... 003C
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/3/0
Renegs Issued/Granted........ 22/8
FForwards/FBacks/Denied...... 9/13/0
Forced FB/FB after FF/MaxREJ. 6/1/9
Last dialed number........... PXXXXXXX
Flex fail


Symbol Rate.................. 3429
Carrier Frequency Hz, Rx/Tx.. 1959/1959
EQM Value (Last/Min/Max)..... 127/20/127
EQM Hits..................... 0
EQM Last 10 Readings......... 127 47 45 50 61 40 44 40 41 46
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallforward due to Low EQM
Last Retrain/Reneg Time...... 1 minutes ago
Handshake Time/Retries....... 15 seconds/0
Non-linear Encoding, Rx/Tx... ON/ON
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 64 state
Pre-Emphasis Index, Tx....... 7
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 4,6
Last Rx/Tx State............. 67/87
Energy at 3750Hz/Average .... 404/200
Last AGC Gain Value.......... 38
Minimum AGC Gain Value....... 38
Maximum AGC Gain Value....... 71
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Remote supports Symbol Rates. 2743 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/187
Frames Errors, Rx/Tx......... 187/5 (1,6%/0,1%)
Frames Count, Rx/Tx.......... 11653/6971
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 120
Error Control Link NAKs...... 5
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 1156232
Characters Sent.............. 309060
Average CPS, Rx/Tx........... 160/42
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 78


И еще...На модемном пуле поддерживается v90. Но у меня не получилось заставить модем заработать на v90. Может, что посоветуете?

[Technical Support]

Начнём с конца:

[tias]

09-11-2003 16:04:08.625 - File: C:\WINNT\system32\unimdm.tsp, Version 5.0.2195 - Retail
09-11-2003 16:04:08.625 - File: C:\WINNT\system32\unimdmat.dll, Version 5.0.2195 - Retail
09-11-2003 16:04:08.625 - File: C:\WINNT\system32\uniplat.dll, Version 5.0.2195 - Retail
09-11-2003 16:04:08.625 - File: C:\WINNT\system32\drivers\modem.sys, Version 5.0.2195 - Retail
09-11-2003 16:04:08.640 - File: C:\WINNT\system32\modemui.dll, Version 5.0.2195 - Retail
09-11-2003 16:04:08.640 - Modem type: IDC 5614BXL VR PnP
09-11-2003 16:04:08.640 - Modem inf path: oem8.inf
09-11-2003 16:04:08.640 - Modem inf section: Modem24
09-11-2003 16:04:08.640 - Opening Modem
09-11-2003 16:04:08.640 - 115200,8,N,1, ctsfl=1, rtsctl=2
09-11-2003 16:04:08.640 - Initializing modem.
09-11-2003 16:04:08.656 - Send: AT&FS38=0S95=41S115=0E0<cr>
09-11-2003 16:04:08.656 - TSP(0000): Making call
09-11-2003 16:04:08.671 - Recv: <cr><lf>OK<cr><lf>
09-11-2003 16:04:08.671 - Interpreted response: OK
09-11-2003 16:04:08.687 - Send: ATS7=60S30=0L1M1\N3%C3&K3B0X4<cr>
09-11-2003 16:04:08.687 - Recv: <cr><lf>OK<cr><lf>
09-11-2003 16:04:08.687 - Interpreted response: OK
09-11-2003 16:04:08.687 - Waiting for a call.
09-11-2003 16:04:08.703 - Send: at#cid=1<cr>
09-11-2003 16:04:08.703 - Recv: <cr><lf>OK<cr><lf>
09-11-2003 16:04:08.703 - Interpreted response: OK
09-11-2003 16:04:08.718 - Send: ATS0=0<cr>
09-11-2003 16:04:08.718 - Recv: <cr><lf>OK<cr><lf>
09-11-2003 16:04:08.718 - Interpreted response: OK
09-11-2003 16:04:08.718 - 115200,8,N,1, ctsfl=1, rtsctl=2
09-11-2003 16:04:08.718 - Initializing modem.
09-11-2003 16:04:08.734 - Send: AT&FS38=0S95=41S115=0E0<cr>
09-11-2003 16:04:08.750 - Recv: <cr><lf>OK<cr><lf>
09-11-2003 16:04:08.750 - Interpreted response: OK
09-11-2003 16:04:08.765 - Send: ATS7=60S30=0L1M1\N3%C3&K3B0X4<cr>
09-11-2003 16:04:08.765 - Recv: <cr><lf>OK<cr><lf>
09-11-2003 16:04:08.765 - Interpreted response: OK
09-11-2003 16:04:08.765 - Dialing.
09-11-2003 16:04:08.765 - TSP(0000): LINEEVENT: LINECALLSTATE_DIALING
09-11-2003 16:04:08.765 - TSP(0000): LINEEVENT: LINECALLSTATE_PROCEEDING
09-11-2003 16:04:08.781 - Send: ATDP#######<cr>
09-11-2003 16:05:28.781 - Timed out waiting for response from modem
09-11-2003 16:05:28.781 - Hanging up the modem.
09-11-2003 16:05:28.796 - Send: ATH<cr>
09-11-2003 16:05:30.218 - Recv: <cr><lf>NO CARRIER<cr><lf>
09-11-2003 16:05:30.218 - Interpreted response: No Carrier
09-11-2003 16:05:30.234 - Send: ATH<cr>
09-11-2003 16:05:30.234 - Recv: <cr><lf>OK<cr><lf>
09-11-2003 16:05:30.234 - Interpreted response: OK
09-11-2003 16:05:30.250 - Send: at#ud<cr>
09-11-2003 16:05:30.250 - Recv: <cr><lf>DIAG
09-11-2003 16:05:30.250 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.250 - Recv: <2A4D3263 0=10><cr><lf>
09-11-2003 16:05:30.250 - Recv: DIAG
09-11-2003 16:05:30.250 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.250 - Recv: <2A4D3263 1=07><cr><lf>
09-11-2003 16:05:30.250 - Recv: DIAG
09-11-2003 16:05:30.250 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.250 - Recv: <2A4D3263 2=00><cr><lf>
09-11-2003 16:05:30.250 - Recv: DIAG
09-11-2003 16:05:30.250 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.250 - Recv: <2A4D3263 3=00><cr><lf>
09-11-2003 16:05:30.250 - Recv: DIAG
09-11-2003 16:05:30.250 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.250 - Recv: <2A4D3263 10=2F><cr><lf>
09-11-2003 16:05:30.250 - Recv: DIAG
09-11-2003 16:05:30.250 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.250 - Recv: <2A4D3263 11=09><cr><lf>
09-11-2003 16:05:30.250 - Recv: DIAG
09-11-2003 16:05:30.250 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.250 - Recv: <2A4D3263 12=64><cr><lf>
09-11-2003 16:05:30.250 - Recv: DIAG
09-11-2003 16:05:30.250 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.265 - Recv: <2A4D3263 20=00><cr><lf>
09-11-2003 16:05:30.265 - Recv: DIAG
09-11-2003 16:05:30.265 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.265 - Recv: <2A4D3263 21=00><cr><lf>
09-11-2003 16:05:30.265 - Recv: DIAG
09-11-2003 16:05:30.265 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.265 - Recv: <2A4D3263 22=0640><cr><lf>
09-11-2003 16:05:30.265 - Recv: DIAG
09-11-2003 16:05:30.265 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.265 - Recv: <2A4D3263 23=0640><cr><lf>
09-11-2003 16:05:30.265 - Recv: DIAG
09-11-2003 16:05:30.265 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.265 - Recv: <2A4D3263 24=0640><cr><lf>
09-11-2003 16:05:30.265 - Recv: DIAG
09-11-2003 16:05:30.265 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.265 - Recv: <2A4D3263 25=0640><cr><lf>
09-11-2003 16:05:30.265 - Recv: DIAG
09-11-2003 16:05:30.265 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.265 - Recv: <2A4D3263 26=2580><cr><lf>
09-11-2003 16:05:30.265 - Recv: DIAG
09-11-2003 16:05:30.265 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.281 - Recv: <2A4D3263 27=2580><cr><lf>
09-11-2003 16:05:30.281 - Recv: DIAG
09-11-2003 16:05:30.281 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.281 - Recv: <2A4D3263 30=00><cr><lf>
09-11-2003 16:05:30.281 - Recv: DIAG
09-11-2003 16:05:30.281 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.281 - Recv: <2A4D3263 31=00><cr><lf>
09-11-2003 16:05:30.281 - Recv: DIAG
09-11-2003 16:05:30.281 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.281 - Recv: <2A4D3263 32=00><cr><lf>
09-11-2003 16:05:30.281 - Recv: DIAG
09-11-2003 16:05:30.281 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.281 - Recv: <2A4D3263 33=00><cr><lf>
09-11-2003 16:05:30.281 - Recv: DIAG
09-11-2003 16:05:30.281 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.281 - Recv: <2A4D3263 34=2580><cr><lf>
09-11-2003 16:05:30.281 - Recv: DIAG
09-11-2003 16:05:30.281 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.281 - Recv: <2A4D3263 35=2580><cr><lf>
09-11-2003 16:05:30.281 - Recv: DIAG
09-11-2003 16:05:30.281 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.281 - Recv: <2A4D3263 40=00><cr><lf>
09-11-2003 16:05:30.281 - Recv: DIAG
09-11-2003 16:05:30.281 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.296 - Recv: <2A4D3263 41=0000><cr><lf>
09-11-2003 16:05:30.296 - Recv: DIAG
09-11-2003 16:05:30.296 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.296 - Recv: <2A4D3263 42=00><cr><lf>
09-11-2003 16:05:30.296 - Recv: DIAG
09-11-2003 16:05:30.296 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.296 - Recv: <2A4D3263 43=00><cr><lf>
09-11-2003 16:05:30.296 - Recv: DIAG
09-11-2003 16:05:30.296 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.296 - Recv: <2A4D3263 44=00><cr><lf>
09-11-2003 16:05:30.296 - Recv: DIAG
09-11-2003 16:05:30.296 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.296 - Recv: <2A4D3263 45=0000><cr><lf>
09-11-2003 16:05:30.296 - Recv: DIAG
09-11-2003 16:05:30.296 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.296 - Recv: <2A4D3263 50=02><cr><lf>
09-11-2003 16:05:30.296 - Recv: DIAG
09-11-2003 16:05:30.296 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.296 - Recv: <2A4D3263 51=02><cr><lf>
09-11-2003 16:05:30.296 - Recv: DIAG
09-11-2003 16:05:30.296 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.312 - Recv: <2A4D3263 52=00000000><cr><lf>
09-11-2003 16:05:30.312 - Recv: DIAG
09-11-2003 16:05:30.312 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.312 - Recv: <2A4D3263 53=00000000><cr><lf>
09-11-2003 16:05:30.312 - Recv: DIAG
09-11-2003 16:05:30.312 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.312 - Recv: <2A4D3263 54=0000><cr><lf>
09-11-2003 16:05:30.312 - Recv: DIAG
09-11-2003 16:05:30.312 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.312 - Recv: <2A4D3263 55=0000><cr><lf>
09-11-2003 16:05:30.312 - Recv: DIAG
09-11-2003 16:05:30.312 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.312 - Recv: <2A4D3263 56=00000000><cr><lf>
09-11-2003 16:05:30.312 - Recv: DIAG
09-11-2003 16:05:30.312 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.312 - Recv: <2A4D3263 57=00000000><cr><lf>
09-11-2003 16:05:30.312 - Recv: DIAG
09-11-2003 16:05:30.312 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.312 - Recv: <2A4D3263 58=0000><cr><lf>
09-11-2003 16:05:30.312 - Recv: DIAG
09-11-2003 16:05:30.312 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.328 - Recv: <2A4D3263 59=0000><cr><lf>
09-11-2003 16:05:30.328 - Recv: DIAG
09-11-2003 16:05:30.328 - Interpreted response: Diagnostic Info
09-11-2003 16:05:30.328 - Recv: <2A4D3263 60=50><cr><lf>
09-11-2003 16:05:30.328 - Recv: <cr><lf>OK<cr><lf>
09-11-2003 16:05:30.328 - Interpreted response: OK
09-11-2003 16:05:30.328 - Diagnostics
09-11-2003 16:05:30.328 - Modem Diagnostics:
09-11-2003 16:05:30.328 - Version 1.0
09-11-2003 16:05:30.328 - Call Setup Result: Data Answering signal detected
09-11-2003 16:05:30.328 - Multi-media mode: Data Only
09-11-2003 16:05:30.328 - DTE-DCE interface mode: Async data
09-11-2003 16:05:30.328 - Received signal power level (in -dBm): 47
09-11-2003 16:05:30.328 - Transmit signal power level (in -dBm): 9
09-11-2003 16:05:30.328 - Estimated noise level (in -dBm): 100
09-11-2003 16:05:30.328 - Transmit Carrier Negotiation Result: V.17
09-11-2003 16:05:30.328 - Receive Carrier Negotiation Result: V.17
09-11-2003 16:05:30.328 - Transmit Carrier symbol rate: 1600
09-11-2003 16:05:30.328 - Receive Carrier symbol rate: 1600
09-11-2003 16:05:30.328 - Transmit Carrier frequency: 1600
09-11-2003 16:05:30.328 - Receive Carrier frequency: 1600
09-11-2003 16:05:30.328 - Initial transmit carrier data rate: 9600
09-11-2003 16:05:30.328 - Initial receive carrier data rate: 9600
09-11-2003 16:05:30.328 - Temporary carrier loss event count: 0
09-11-2003 16:05:30.328 - Carrier Rate re-negotiation event count: 0
09-11-2003 16:05:30.328 - Carrier Retrains requested: 0
09-11-2003 16:05:30.328 - Carrier Retrain requests granted: 0
09-11-2003 16:05:30.328 - Final transmit carrier rate: 9600
09-11-2003 16:05:30.328 - Final receive carrier rate: 9600
09-11-2003 16:05:30.328 - Protocol Negotiation Result: Disable/none
09-11-2003 16:05:30.328 - Error control frame size: 0
09-11-2003 16:05:30.328 - Error control link timeouts: 0
09-11-2003 16:05:30.328 - Error control link NAKs: 0
09-11-2003 16:05:30.328 - Compression Negotiation Result: None
09-11-2003 16:05:30.328 - Compression dictionary size: 0
09-11-2003 16:05:30.328 - Transmit flow control: V.24 ckt 106/133
09-11-2003 16:05:30.328 - Receive flow control: V.24 ckt 106/133
09-11-2003 16:05:30.328 - Transmit characters sent from DTE: 0
09-11-2003 16:05:30.328 - Received characters sent to DTE: 0
09-11-2003 16:05:30.328 - Transmit characters lost (data overrun errors from DTE): 0
09-11-2003 16:05:30.328 - Received characters lost (data overrun errors to DTE): 0
09-11-2003 16:05:30.328 - Transmit Frame count: 0
09-11-2003 16:05:30.328 - Received Frame count: 0
09-11-2003 16:05:30.328 - Transmit Frame error count: 0
09-11-2003 16:05:30.328 - Received Frame error count: 0
09-11-2003 16:05:30.328 - Termination Cause: Any Key Abort
09-11-2003 16:05:30.328 - 115200,8,N,1, ctsfl=1, rtsctl=2
09-11-2003 16:05:30.328 - Initializing modem.
09-11-2003 16:05:30.343 - Send: AT&FS38=0S95=41S115=0E0<cr>
09-11-2003 16:05:30.359 - Recv: <cr><lf>OK<cr><lf>
09-11-2003 16:05:30.359 - Interpreted response: OK
09-11-2003 16:05:30.375 - Send: ATS7=60S30=0L1M1\N3%C3&K3B0X4<cr>
09-11-2003 16:05:30.375 - Recv: <cr><lf>OK<cr><lf>
09-11-2003 16:05:30.375 - Interpreted response: OK
09-11-2003 16:05:30.375 - Waiting for a call.
09-11-2003 16:05:30.390 - Send: at#cid=1<cr>
09-11-2003 16:05:30.390 - Recv: <cr><lf>OK<cr><lf>
09-11-2003 16:05:30.390 - Interpreted response: OK
09-11-2003 16:05:30.406 - Send: ATS0=0<cr>
09-11-2003 16:05:30.406 - Recv: <cr><lf>OK<cr><lf>
09-11-2003 16:05:30.406 - Interpreted response: OK
09-11-2003 16:05:30.406 - TSP(0000): LINEEVENT: LINECALLSTATE_DISCONNECTED(0x4000)
09-11-2003 16:05:30.406 - TSP(0000): LINEEVENT: LINECALLSTATE_IDLE
09-11-2003 16:05:30.406 - TSP(0000): Dropping call
09-11-2003 16:05:30.406 - TSP(0000): Closing Call
09-11-2003 16:05:30.406 - Session Statistics:
09-11-2003 16:05:30.406 - Reads : 24 bytes
09-11-2003 16:05:30.406 - Writes: 70 bytes


---------------------------------------------------------------------------------------------------
Программа сбора статистики только нули показывает.

[Technical Support]

[tias]

OK

OK
R00T00R01T02T0300398
NO CARRIER
at%s%s1
Time Online.................. 00:00:00
Termination Reason........... NO CONNECT
Tx Rate (Last/Init/Min/Max).. NA
Rx Rate (Last/Init/Min/Max).. NA
Modulation................... V.34bis
Protocol/Compression......... NA
Line Quality................. NA
Tx/Power Drop/Rx Level....... 9/NA/NA
SNR Last/Min/Max............. NA/NA/NA
Highest Rx/Tx State.......... 00/00
EQM Sum...................... 0000
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 0/0
FForwards/FBacks/Denied...... 0/0/0
Forced FB/FB after FF/MaxREJ. 0/0/0
Last dialed number........... P 9800398
Flex fail

BEGINaa255ab255ac0ad255ba255bb255bc0bd255ca255cb255cc170da255ea255eb255fa0fb255f
c0ga9gb255ha255hb255hc0hd0he0hf0hg0hh255hi255hj255hk255hl255hm255hn255ho255hp255
hq255hr255hs255ia255ib255ic0ja0jb0jc0jd0je0jf0ka255kb255kc255kd255ke255kf255kg25
5kh255ki255kj255kk255kl255km255kn255la0lb0lc1ld3ma0mb0mc0na255nb255oa255ob255oc2
55od255oe255of255og255pa0pb0pc255pd255qa22qb0qc255ra255rb255rc255rd255re255rf255
rg255rh128sa255sb255sc255sd255ta255tb0tc0td0te255tf255tg255th0ti0END

OK

[Technical Support]

Случай очень интересный!

Прежде чем продолжить обсуждение, небольшой совет: после запуска Hyperterminal выполните команду:

atz
OK

Дело в том, что TAPI выключает вывод эхо на команды. Вам приходилось набирать команды вслепую, что не очень удобно. Поэтому предлагается напечатать вслепую atz, нажать <Enter> и после этого модем начнёт выводить эхо на вводимые символы.

Теперь к проблеме: похоже, удалённый модем вообще не умеет работать с V.90. Давайте проведём ещё два эксперимента:

atz
OK

at +a8e=,,,0
OK

at s202=4 dp9800398

и ещё один:

atz
OK

at +ms=11
OK

at s202=4 dp9800398

Если в результате любого из экспериментов появится сообщение CONNECT - разъединитесь. После разъединения (или если NO CARRIER появится "само собой") выдайте команду:

at%s%s1

Как и в прошлый раз, нам понадобится протокол работы в Hyperterminal: скопируйте и вставьте в сообщение.
_________________
Inpro
Technical Support

[tias]

OK
at +a8e=,,,0
OK
R00T00R01T02T03R02T04T05R20T20R21T21R22T22R23T23R24T24R25T25R26T26T27R27T28R28R2
9R2CT2AR2ET2CR2FT40T44T45T46T47R41T48R42R43R45T60R46R47T61R48T62R49R61T63T64R62T
65T66R63R65T67T66T67R67
CONNECT 40000/V90/LAPM/V42BIS/24000:TX/40000:RX

Welcome to TCnet!
login: tias
Password: R61T81R62T82T84T85R63R65T86T87R67R00T20R21T21R22R23T22R24T24R25T25R26T
26T27R27T28R28R29R2AT2AR2CT2CR2ER2FT40T44T45T46T47T48R41R42R43R45T60R46R60R47T61
R48T62R49R61T63T64R62T65T66R63R65T67T66T67R67R61T81R62T82T84T85R63R65T86T87R67R0
0T20R20R21T21R22R23T22R24T24R25T25R26T26T27R27T28R28R29R2AT2AR2CT2CR2ER2FT40T44T
45T46T47R41T48R42R43R45T60R46R47T61R48T62R49R61T63T64R62T65T66R63R65T67T66T67R67
R61T81R62T82T84T85R63R65T86T87R67R00T20R20R21T21R22R23T22R24T24R25T25R26T26T27R2
7T28R28R29R2AT2AR2CT2CR2ER2FT40T44T45T46T47R41T48R42R43R45T60R46R47T61R48T62R49R
61T63T64T65R62R21T20T21R22R23T22R24T24R25T25R26T26T27R27T28R28R29R2AT2AR2CT2CR2E
R2FT40T44T45T46T47T48R41R42R43R45T60R46R47T61R48T62R49R61T63T64R62T65T66R63R00R2
1T20T21R22R23T22R24T24R25T25R26T26T27R27T28R28R29R2AT2AR2CT2CR2ET40T44T45T46T47T
48R40R41R46T60R47R48R60T61T62T63R63R64T65R65R67T66T67R00T20R20R21T21R22R23T22R24
T24R25T25R26T26T27R27T28R28R29R2AT2AR2CT2CR2ET40T44T45T46T47R40T48R41R46T60R47R4
8R60T61T62T63R63R64T65R67T66T67T81T82T83R83R84T85R67T86T87R00T20R20R21T21R22R23T
22R24T24R25T25R26T26T27R27T28R28R29R2AT2AR2CT2CR2ET40T44T45T46T47T48R40R41R46T60
R47R48R60T61T62T63R63R64T65R67T66T67T81T82T83R83R84T85R67T86T87R83T81R84T82T83T8
5R85T86R67T87login: R83T81R84T82T83T85R85R67T86T87R83T81R84T82T83T85R85T86R67T87




atz
OK
at +ms=11
OK
R00T00R01T02T03R02T04T05R20T20R22T21R23T22R27T28R28R29R2AR2DR2BT29R24T24R25T25R2
CT2CR40T40R41R46R47R48T44T45T46T47T48R60R61R63T62T63R64T65R67T67
CONNECT 33600/V34/LAPM/V42BIS/28800:TX/33600:RX

Welcome to TCnet!
login: tiasR83T81R84T82T83T84T85R85R67T86T87
Password: T81T82T83R83R84T85R67T86T87T81T82T83R83R84T85R85T86R67T87R83T81R84T82T
83T85R85R67T86T87T81T82T83R83R84T84T85R67T86T87

-------------------------------------------------------------------------------
Вот все логи...

Спасибо, что так оперативно отвечаете!
Сервис просто замечательный!

[Technical Support]

Ага, вот и V.90 появился:

CONNECT 40000/V90/LAPM/V42BIS/24000:TX/40000:RX

Похоже, удалённому модему мешал V.8bis... Теперь делаем так: впишите в строку инициализации в свойствах модема команду:

+A8E=,,,0

и попробуйте поработать минут 5-10. Покажите статистику.
_________________
Inpro
Technical Support

[tias]

Строка инициализации

at +a8e=,,,0

=======================================================
Inpro IDC Modems Diagnostics, Version 1.0.1.31
12.09.2003 19:44:09 - Outbound Call by RemoteAccess
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.23

Time Online.................. 00:10:11
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 21600/24000/21600/28800 bps
Rx Rate (Last/Init/Min/Max).. 33600/38667/31200/38667 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 127
Tx/Power Drop/Rx Level....... 15/0/21
SNR Last/Min/Max............. 37/32/37
Highest Rx/Tx State.......... 67/67
EQM Sum...................... 002E
RBS Pattern.................. 00
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 7/6/1
Renegs Issued/Granted........ 3/9
FForwards/FBacks/Denied...... 2/8/0
Forced FB/FB after FF/MaxREJ. 0/1/3
Last dialed number........... PXXXXXXX
Flex fail

Symbol Rate.................. 3429
Carrier Frequency Hz, Rx/Tx.. 1959/1959
EQM Value (Last/Min/Max)..... 127/5/127
EQM Hits..................... 0
EQM Last 10 Readings......... 127 36 51 35 34 84 35 32 127 127
Last Retrain/Reneg Status.... Remote Retrain
Last Retrain/Reneg Reason.... Remote Retrain
Reason for V.34 Fallback..... Data Pump decision to Fallback
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 20 seconds/0
Non-linear Encoding, Rx/Tx... ON/ON
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 64 state
Pre-Emphasis Index, Tx....... 7
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 5,2
Last Rx/Tx State............. 67/67
Energy at 3750Hz/Average .... 270/124
Auto Gain Amplitude, db...... 10
Last AGC Gain Value.......... 86
Minimum AGC Gain Value....... 81
Maximum AGC Gain Value....... 97
Detection of 120 Hz Tones.... Yes
Detection of Dual PCM........ No
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Remote supports Symbol Rates. 2743 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/34
Frames Errors, Rx/Tx......... 34/4 (0,6%/0,1%)
Frames Count, Rx/Tx.......... 5900/3676
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 60
Error Control Link NAKs...... 4
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 627078
Characters Sent.............. 147578
Average CPS, Rx/Tx........... 1026/241
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 58

[Technical Support]

Ну что же, получили вполне предсказуемый результат. Модемы некоторое время помучились на V.90 и затем перешли на V.34. Момент перехода Вы могли заметить визуально: погас индикатор HS на лицевой панели модема.

Мы тут немного поэкспериментировали с номером 980-0398. Оказалось, что проблем с V.8bis у этого пула нет. V.8bis модемами пула не поддерживается, но работа при включённом V.8bis всё-таки возможна. Скорее всего, просто произошёл случайный сбой во время Вашего первого эксперимента.

Ещё выяснилось, что модемы Вашего провайдера терпимо относятся к ограничению скорости передачи. Поэтому стоит попробовать ограничить скорость, это должно помочь избавиться от перетренировок, запрашиваемых удалённым модемом.

Попробуйте изменить строку инициализации следующим образом:

M4 S202.5=1 +A8E=,,,0; +MS=,,28000,,,,14400

и повторите эксперимент. Команда M4 заставит модем включать динамик во время перетренировок. Если они будут происходить часто (каждую минуту или чаще) - можно рассоединяться.

Покажите статистику, что вышло с такими установками...
_________________
Inpro
Technical Support

[tias]

Inpro IDC Modems Diagnostics, Version 1.0.1.31
12.09.2003 23:06:37 - Outbound Call by RemoteAccess
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.23

Time Online.................. 00:28:50
Termination Reason........... NO REMOTE RESPONSE
Tx Rate (Last/Init/Min/Max).. 14400/14400/14400/14400 bps
Rx Rate (Last/Init/Min/Max).. 34667/38667/29333/42667 bps
Modulation................... V.90
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 127
Tx/Power Drop/Rx Level....... 15/0/19
SNR Last/Min/Max............. 37/34/39
Highest Rx/Tx State.......... 67/87
EQM Sum...................... 0110
RBS Pattern.................. 00
Rate Drop.................... 1
Digital Loss................. 2000
Retrains Issued/Granted/Auto. 22/0/9
Renegs Issued/Granted........ 29/0
FForwards/FBacks/Denied...... 19/32/0
Forced FB/FB after FF/MaxREJ. 0/4/3
Last dialed number........... PXXXXXXX
V90

Symbol Rate.................. 3200
Carrier Frequency Hz, Tx..... 1829
EQM Value (Last/Min/Max)..... 127/4/127
EQM Hits..................... 0
EQM Last 10 Readings......... 127 127 125 126 126 126 11 8 15 8
Last Retrain/Reneg Status.... Local Fast Retrain
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 20 seconds/0
Non-linear Encoding, Rx/Tx... OFF/ON
Precoding, Rx/Tx............. OFF/ON
Shaping, Rx/Tx............... OFF/ON
Trellis Encoding, Tx......... 64 state
Pre-Emphasis Index, Tx....... 7
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 5,1
Last Rx/Tx State............. 61/84
Energy at 3750Hz/Average .... 303/0
Auto Gain Amplitude, db...... 10
Last AGC Gain Value.......... 90
Minimum AGC Gain Value....... 87
Maximum AGC Gain Value....... 90
Detection of 120 Hz Tones.... Yes
Detection of Dual PCM........ No
V.90 RBS Pattern............. 00
V.90 Alternating RBS Pattern. 00
V.90 Digital Pad Value, db... 0,0
V.90 Optimal Speed........... 34667 bps (Reg.S120=6)
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Remote supports Symbol Rates. 2743 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 0/35
Frames Errors, Rx/Tx......... 35/2 (1,0%/0,0%)
Frames Count, Rx/Tx.......... 3435/4924
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 155
Error Control Link NAKs...... 2
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 215193
Characters Sent.............. 80031
Average CPS, Rx/Tx........... 124/46
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 56

---------------------------------------------------------
В принципе ретрэйны частые...может можно что-нибудь улучшить?

[Technical Support]

Похоже, смысла мучаться с V.90 нет. У Вас, скорее всего, аналоговая АТС, и довольно шумная.

Попробуйте перейти на V.34. Соответствующая строка инициализации:

M4 +A8E=,,,0; +MS=11,,,,,,14400
_________________
Inpro
Technical Support