Помогите настроить модем

[SAper]

Есть модем IDC-5614BXL/VR+ прошивка 2.23. линия цифровая.
Как нибудь можно повысить скорость вот статистика
Inpro IDC Modems Diagnostics, Version 1.0.1.30
26.06.03 13:01:01 - Direct Log Write Entry
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.23

Time Online.................. 00:05:54
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 31200/28800/28800/31200 bps
Rx Rate (Last/Init/Min/Max).. 54667/46667/46667/54667 bps
Modulation................... V.90
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 29
Tx/Power Drop/Rx Level....... 15/1/18
SNR Last/Min/Max............. 43/43/43
Highest Rx/Tx State.......... 67/87
EQM Sum...................... 009D
RBS Pattern.................. 00
Rate Drop.................... 1
Digital Loss................. 2000
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 4/0
FForwards/FBacks/Denied...... 4/0/0
Forced FB/FB after FF/MaxREJ. 0/0/3
Last dialed number........... P33111
V90 9481834246E0


Symbol Rate.................. 3200
Carrier Frequency Hz, Tx..... 1829
EQM Value (Last/Min/Max)..... 29/10/33
EQM Hits..................... 0
EQM Last 10 Readings......... 28 26 31 30 30 25 29 31 26 30
Last Retrain/Reneg Status.... Local Fast Retrain
Last Retrain/Reneg Reason.... Local Fallforward due to Low EQM
Last Retrain/Reneg Time...... 4 minutes ago
Handshake Time/Retries....... 22 seconds/0
Non-linear Encoding, Rx/Tx... OFF/OFF
Precoding, Rx/Tx............. OFF/OFF
Shaping, Rx/Tx............... OFF/OFF
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 1
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 1,9
Last Rx/Tx State............. 67/87
Energy at 3750Hz/Average .... 1440/1157
Auto Gain Amplitude, db...... 10
Detection of 120 Hz Tones.... No
Detection of Dual PCM........ No
V.90 RBS Pattern............. 00
V.90 Alternating RBS Pattern. 00
V.90 Digital Pad Value, db... 0,0
V.90 Optimal Speed........... No Limit (Reg.S120=0)
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 02
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Server (Digital)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/10
Frames Errors, Rx/Tx......... 10/4 (0,2%/0,2%)
Frames Count, Rx/Tx.......... 5289/2662
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 2
Error Control Link NAKs...... 4
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 931408
Characters Sent.............. 80288
Average CPS, Rx/Tx........... 2631/226
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 61

Если нужна более продолжительного времени, то в выходные бедет

[Technical Support]

В Вашей статистике всё просто идеально Модем соединился на скорости 46667, но очень быстро (меньше, чем за минуту) поднялся до 54667 бит/с. Вам стоит несколько повысить агрессивность модема в выборе скорости, чтобы сразу начинать "повыше" (например, с 53333 бит/с. Попробуйте прописать в строку инициализации:

S91=15 S210.7=1 S17=48
_________________
Inpro
Technical Support

[SAper]

Вот что получилось:


Inpro IDC Modems Diagnostics, Version 1.0.1.30
27.06.03 10:24:46 - Direct Log Write Entry
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.23

Time Online.................. 00:03:08
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 31200/28800/28800/31200 bps
Rx Rate (Last/Init/Min/Max).. 48000/48000/48000/54667 bps
Modulation................... V.90
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 16
Tx/Power Drop/Rx Level....... 15/1/18
SNR Last/Min/Max............. 43/43/43
Highest Rx/Tx State.......... 67/87
EQM Sum...................... 009C
RBS Pattern.................. 00
Rate Drop.................... 1
Digital Loss................. 2000
Retrains Issued/Granted/Auto. 1/0/0
Renegs Issued/Granted........ 4/1
FForwards/FBacks/Denied...... 4/1/0
Forced FB/FB after FF/MaxREJ. 0/0/2
Last dialed number........... P33111
V90 9481834246E0


Symbol Rate.................. 3200
Carrier Frequency Hz, Tx..... 1829
EQM Value (Last/Min/Max)..... 16/11/127
EQM Hits..................... 0
EQM Last 10 Readings......... 12 15 14 13 15 13 29 29 26 30
Last Retrain/Reneg Status.... Remote Rate Renegotiation
Last Retrain/Reneg Reason.... Remote Rate Renegotiation
Last Retrain/Reneg Time...... 1 minutes ago
Handshake Time/Retries....... 22 seconds/0
Non-linear Encoding, Rx/Tx... OFF/OFF
Precoding, Rx/Tx............. OFF/OFF
Shaping, Rx/Tx............... OFF/OFF
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 1
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 1,9
Last Rx/Tx State............. 67/87
Energy at 3750Hz/Average .... 1406/1130
Auto Gain Amplitude, db...... 10
Detection of 120 Hz Tones.... No
Detection of Dual PCM........ No
V.90 RBS Pattern............. 00
V.90 Alternating RBS Pattern. 00
V.90 Digital Pad Value, db... 0,0
V.90 Optimal Speed........... No Limit (Reg.S120=0)
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 02
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Server (Digital)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/7
Frames Errors, Rx/Tx......... 7/0 (0,2%/0,0%)
Frames Count, Rx/Tx.......... 2972/1675
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 0
Error Control Link NAKs...... 0
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 551236
Characters Sent.............. 66239
Average CPS, Rx/Tx........... 2932/352
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 61

[Technical Support]

Пока у Вас ничего не получилось Видите эту строчку:

Tx/Power Drop/Rx Level....... 15/1/18

Если бы указанная строка инициализации "сработала", то в Power Drop был бы 0 (поскольку S210.7=1 запрещает Power Drop).

Значит, Вы прописали команды куда-то "не туда". Их нужно вписать в строку инициализации в свойствах модема.
_________________
Inpro
Technical Support

[SAper]

Вроде туды я написал
Можь где нибудь есщо надо?

[Technical Support]

Нет, больше никуда команду прописывать не надо. Там же, в свойствах модема, есть "галочка", включающая сбор журнала модема. Посмотрите, появляется ли Ваша команда инициализации в журнале, прямо перед набором номера.
_________________
Inpro
Technical Support

[SAper]

Прикол, ваще после постановки галки, как вы сказали.
строка заработала.
вот что получилось:


Inpro IDC Modems Diagnostics, Version 1.0.1.30
29.06.03 10:56:21 - Outbound Call by Remote Access
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.23

Time Online.................. 00:01:55
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 31200/28800/28800/31200 bps
Rx Rate (Last/Init/Min/Max).. 54667/54667/54667/54667 bps
Modulation................... V.90
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 31
Tx/Power Drop/Rx Level....... 15/0/18
SNR Last/Min/Max............. 43/43/43
Highest Rx/Tx State.......... 65/87
EQM Sum...................... 0063
RBS Pattern.................. 00
Rate Drop.................... 1
Digital Loss................. 2000
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 0/1
FForwards/FBacks/Denied...... 0/0/0
Forced FB/FB after FF/MaxREJ. 0/0/1
Last dialed number........... P33111
V90 9481834246E0


Symbol Rate.................. 3200
Carrier Frequency Hz, Tx..... 1829
EQM Value (Last/Min/Max)..... 31/22/45
EQM Hits..................... 0
EQM Last 10 Readings......... 28 30 31 30 29 30 29 30 28 33
Last Retrain/Reneg Status.... Remote Rate Renegotiation
Last Retrain/Reneg Reason.... Remote Rate Renegotiation
Last Retrain/Reneg Time...... 1 minutes ago
Handshake Time/Retries....... 22 seconds/0
Non-linear Encoding, Rx/Tx... OFF/OFF
Precoding, Rx/Tx............. OFF/OFF
Shaping, Rx/Tx............... OFF/OFF
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 1
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 1,9
Last Rx/Tx State............. 65/87
Energy at 3750Hz/Average .... 1425/1146
Auto Gain Amplitude, db...... 10
Detection of 120 Hz Tones.... No
Detection of Dual PCM........ No
V.90 RBS Pattern............. 00
V.90 Alternating RBS Pattern. 00
V.90 Digital Pad Value, db... 0,0
V.90 Optimal Speed........... No Limit (Reg.S120=0)
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 02
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Server (Digital)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/2
Frames Errors, Rx/Tx......... 2/0 (0,2%/0,0%)
Frames Count, Rx/Tx.......... 915/515
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 0
Error Control Link NAKs...... 0
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 130254
Characters Sent.............. 39350
Average CPS, Rx/Tx........... 1132/342
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 61

[Technical Support]

[SAper]

тут наверно виновата звонилка Power Dialer, потому что когда я подключаюсть через стандартную звонилку, те виндовскую, то строка выполняется

[Technical Support]

Конкретно про Power Dialer ничего не скажем - не пользовались, но многие звонилки пользуются своими собственными настройками и игнорируют настройки модема в свойствах в Windows.
_________________
Inpro
Technical Support

[SAper]

а может подскажете какой зворнилкой лучше пользоваться?
Самое главное что там долно быть это таймер

[Technical Support]

У нас экспертов в области звонилок нет - не пользуемся. Лучше всего обратиться в какой-нибудь форум по софту.
_________________
Inpro
Technical Support

[SAper]

вот подлиннее статистика



Inpro IDC Modems Diagnostics, Version 1.0.1.30
04.07.03 12:14:32 - Outbound Call by Remote Access
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.23

Time Online.................. 00:17:44
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 31200/28800/28800/31200 bps
Rx Rate (Last/Init/Min/Max).. 53333/54667/52000/54667 bps
Modulation................... V.90
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 36
Tx/Power Drop/Rx Level....... 15/0/18
SNR Last/Min/Max............. 43/43/43
Highest Rx/Tx State.......... 67/87
EQM Sum...................... 0068
RBS Pattern.................. 00
Rate Drop.................... 1
Digital Loss................. 2000
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 10/0
FForwards/FBacks/Denied...... 1/9/0
Forced FB/FB after FF/MaxREJ. 9/6/10
Last dialed number........... P33111
V90 9481834246E0


Symbol Rate.................. 3200
Carrier Frequency Hz, Tx..... 1829
EQM Value (Last/Min/Max)..... 36/17/119
EQM Hits..................... 0
EQM Last 10 Readings......... 36 36 38 40 36 38 35 35 35 37
Last Retrain/Reneg Status.... Local Fast Retrain
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 2 minutes ago
Handshake Time/Retries....... 21 seconds/0
Non-linear Encoding, Rx/Tx... OFF/OFF
Precoding, Rx/Tx............. OFF/OFF
Shaping, Rx/Tx............... OFF/OFF
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 1
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 1,3
Last Rx/Tx State............. 67/87
Energy at 3750Hz/Average .... 1425/1146
Auto Gain Amplitude, db...... 10
Detection of 120 Hz Tones.... No
Detection of Dual PCM........ No
V.90 RBS Pattern............. 00
V.90 Alternating RBS Pattern. 00
V.90 Digital Pad Value, db... 0,0
V.90 Optimal Speed........... No Limit (Reg.S120=0)
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 02
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Server (Digital)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/117
Frames Errors, Rx/Tx......... 373/10 (1,0%/0,1%)
Frames Count, Rx/Tx.......... 36578/13237
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 8
Error Control Link NAKs...... 10
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 4366158
Characters Sent.............. 413454
Average CPS, Rx/Tx........... 4103/388
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 61

[SAper]

вот статистика сегоднешней ночи.

Inpro IDC Modems Diagnostics, Version 1.0.1.30
05.07.03 8:44:47 - Outbound Call by Remote Access
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.23

Time Online.................. 06:43:52
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 31200/28800/28800/31200 bps
Rx Rate (Last/Init/Min/Max).. 53333/52000/50667/53333 bps
Modulation................... V.90
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 42
Tx/Power Drop/Rx Level....... 15/0/18
SNR Last/Min/Max............. 43/43/43
Highest Rx/Tx State.......... 67/87
EQM Sum...................... 007A
RBS Pattern.................. 00
Rate Drop.................... 1
Digital Loss................. 2000
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 9/1
FForwards/FBacks/Denied...... 2/7/0
Forced FB/FB after FF/MaxREJ. 4/4/11
Last dialed number........... P33111
V90 9481834246E0


Symbol Rate.................. 3200
Carrier Frequency Hz, Tx..... 1829
EQM Value (Last/Min/Max)..... 42/19/127
EQM Hits..................... 0
EQM Last 10 Readings......... 40 39 41 42 45 43 44 39 38 43
Last Retrain/Reneg Status.... Local Fast Retrain
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 32 minutes ago
Handshake Time/Retries....... 29 seconds/0
Non-linear Encoding, Rx/Tx... OFF/OFF
Precoding, Rx/Tx............. OFF/OFF
Shaping, Rx/Tx............... OFF/OFF
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 1
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 2,3
Last Rx/Tx State............. 65/87
Energy at 3750Hz/Average .... 1449/1164
Auto Gain Amplitude, db...... 10
Detection of 120 Hz Tones.... No
Detection of Dual PCM........ No
V.90 RBS Pattern............. 00
V.90 Alternating RBS Pattern. 00
V.90 Digital Pad Value, db... 0,0
V.90 Optimal Speed........... No Limit (Reg.S120=0)
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 02
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Server (Digital)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/219
Frames Errors, Rx/Tx......... 1499/20 (0,1%/0,0%)
Frames Count, Rx/Tx.......... 1110744/440320
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 17
Error Control Link NAKs...... 20
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 140351528
Characters Sent.............. 8960054
Average CPS, Rx/Tx........... 5791/369
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 61

[Technical Support]

Не очень хорошо модему живётся на 54667: довольно большое количество сбойных кадров данных при приёме. Если подобная картина наблюдается часто, можно попробовать ограничить скорость приёма до 52000 или 53333 (+MS=12,,,52000 или +MS=12,,,533333).
_________________
Inpro
Technical Support