Помогите с 5614BXL/VR+

[Molyan]

Подскажите пожайлуста что можно зделать с модемом для нормальной работы, скорость соединения маленькая, страницы грузяться как то кусками а иногда модем виснет и порой отклучаеться от интернета...
Inpro IDC Modems Diagnostics, Version: 1.1.4.39
24.08.2008 16:21:14 - Direct Log Write Entry
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.26
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: <none>

Time Online.................. 00:20:42
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 19200/16800/16800/21600 bps
Rx Rate (Last/Init/Min/Max).. 36000/32000/32000/38667 bps
Modulation................... V.90
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 26
Tx/Power Drop/Rx Level....... 15/0/18
SNR Last/Min/Max............. 43/43/43
Highest Rx/Tx State.......... 65/87
EQM Sum...................... 011B
RBS Pattern.................. 00
Rate Drop.................... 0
Digital Loss................. 2000
Retrains Issued/Granted/Auto. 0/2/1
Renegs Issued/Granted........ 16/2
FForwards/FBacks/FEQM/Denied. 10/6/1/0
Forced FB/FB after FF/MaxREJ. 3/1/7
Last dialed number........... P8W8007072850
V90 9481834246E0


Negotiation Result (Rx/Tx)... V.90 Issue 1 (asymmetric)/V.34
Symbol Rate (Rx/Tx).......... 8000/3200
Carrier Frequency Hz, Tx..... 1829
EQM Value (Last/Min/Max)..... 26/13/107
EQM Hits..................... 0
EQM Last 10 Readings......... 25 26 26 24 24 23 26 28 28 27
Fast Retrains (RRWS) Count... 10
Last Retrain/Reneg Status.... Remote Retrain
Last Retrain/Reneg Reason.... Remote Retrain
Last Retrain/Reneg Time...... 1 minutes ago
Handshake Time/Retries....... 27 seconds/0
Non-linear Encoding, Rx/Tx... OFF/OFF
Precoding, Rx/Tx............. OFF/OFF
Shaping, Rx/Tx............... OFF/OFF
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 2
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 9,8
Last Rx/Tx State............. 65/67
Energy at 3750Hz/Average .... 1680/228
Auto Gain Amplitude, db...... 10
Rx Level (Last/Min/Max), -dB. 17,9/17,9/17,9
Detection of 120 Hz Tones.... Yes
Detection of Dual PCM........ No
V.90 RBS Pattern............. 00
V.90 Alternating RBS Pattern. 00
V.90 Digital Pad Value, db... 0,0
V.90 Optimal Speed........... 36000 bps (Reg.S120=7)
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 02
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Server (Digital)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... External
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/65
Frames Errors, Rx/Tx......... 65/17 (1,0%/0,9%)
Frames Count, Rx/Tx.......... 6797/1881
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 10
Error Control Link NAKs...... 17
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 732 548
Characters Sent.............. 123 486
Average CPS, Rx/Tx........... 589/99
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 61

Заранее вам благодарен!!!

[Technical Support]

В такой ситуации лучше всего отказаться от V.90 и перейти на V.34bis. Соответствующая команда (прописывается в строке инициализации модема в Windows):

S91=12 S210.7=1 +MS=11
_________________
Inpro
Technical Support