| Предыдущая тема :: Следующая тема |
| Автор |
Сообщение |
Mirage
Junior member
Зарегистрирован: 27.03.2008
Сообщения: 2
|
 Добавлено: Чт Мар 27, 2008 10:25 am Заголовок сообщения: Модем IDC-1914BXL и Hylafax |
 |
|
Никак не выходит прикрутить модем IDC-1914BXL (MODEM IDC-1914BXL V.32TERBO/V.42BIS FIRMWARE BY MIKE TELIS, VER. 2.19 192144) к Hylafax. Готового файла конфига для этого модема найти не смог. Тот конфиг который Hylafax сама ему делает (видимо типовой) не подходит (модем трубку снимает но факс не проходит) вот лог:
| Код: |
Mar 26 19:08:34.34: [ 3607]: SESSION BEGIN 000000038 74951234567
Mar 26 19:08:34.34: [ 3607]: HylaFAX (tm) Version 4.3.4
Mar 26 19:08:34.34: [ 3607]: <-- [4:ATA\r]
Mar 26 19:08:40.43: [ 3607]: --> [7:CONNECT]
Mar 26 19:08:40.44: [ 3607]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS0'
Mar 26 19:08:40.44: [ 3607]: RECV FAX: begin
Mar 26 19:08:40.44: [ 3607]: <-- data [32]
Mar 26 19:08:40.44: [ 3607]: <-- data [2]
Mar 26 19:08:42.36: [ 3607]: --> [7:CONNECT]
Mar 26 19:08:42.37: [ 3607]: <-- data [23]
Mar 26 19:08:42.37: [ 3607]: <-- data [2]
Mar 26 19:08:43.09: [ 3607]: --> [7:CONNECT]
Mar 26 19:08:43.10: [ 3607]: <-- data [13]
Mar 26 19:08:43.10: [ 3607]: <-- data [2]
Mar 26 19:08:43.64: [ 3607]: --> [2:OK]
Mar 26 19:08:43.64: [ 3607]: <-- [9:AT+FRH=3\r]
Mar 26 19:08:44.33: [ 3607]: --> [7:CONNECT]
Mar 26 19:08:45.59: [ 3607]: --> [2:OK]
Mar 26 19:08:45.60: [ 3607]: REMOTE wants 9600 bit/s
Mar 26 19:08:45.60: [ 3607]: REMOTE wants A4 page width (215 mm)
Mar 26 19:08:45.60: [ 3607]: REMOTE wants unlimited page length
Mar 26 19:08:45.60: [ 3607]: REMOTE wants 3.85 line/mm
Mar 26 19:08:45.60: [ 3607]: REMOTE wants 2-D MR
Mar 26 19:08:45.60: [ 3607]: RECV training at v.29 9600 bit/s
Mar 26 19:08:45.60: [ 3607]: <-- [10:AT+FRM=96\r]
Mar 26 19:08:46.15: [ 3607]: --> [7:CONNECT]
Mar 26 19:08:47.69: [ 3607]: RECV: TCF 1841 bytes, 0% non-zero, 1820 zero-run
Mar 26 19:08:47.70: [ 3607]: --> [10:NO CARRIER]
Mar 26 19:08:47.70: [ 3607]: <-- [9:AT+FRS=7\r]
Mar 26 19:08:47.75: [ 3607]: --> [5:ERROR]
Mar 26 19:08:47.75: [ 3607]: MODEM Command error
Mar 26 19:08:47.75: [ 3607]: <-- [9:AT+FRH=3\r]
Mar 26 19:08:50.98: [ 3607]: --> [7:CONNECT]
Mar 26 19:08:52.25: [ 3607]: --> [2:OK]
Mar 26 19:08:52.25: [ 3607]: REMOTE wants 9600 bit/s
Mar 26 19:08:52.25: [ 3607]: REMOTE wants A4 page width (215 mm)
Mar 26 19:08:52.26: [ 3607]: REMOTE wants unlimited page length
Mar 26 19:08:52.26: [ 3607]: REMOTE wants 3.85 line/mm
Mar 26 19:08:52.26: [ 3607]: REMOTE wants 2-D MR
Mar 26 19:08:52.26: [ 3607]: RECV training at v.29 9600 bit/s
Mar 26 19:08:52.26: [ 3607]: <-- [10:AT+FRM=96\r]
Mar 26 19:08:52.80: [ 3607]: --> [7:CONNECT]
Mar 26 19:08:54.34: [ 3607]: RECV: TCF 1839 bytes, 0% non-zero, 1819 zero-run
Mar 26 19:08:54.35: [ 3607]: --> [10:NO CARRIER]
Mar 26 19:08:54.35: [ 3607]: <-- [9:AT+FRS=7\r]
Mar 26 19:08:54.40: [ 3607]: --> [5:ERROR]
Mar 26 19:08:54.40: [ 3607]: MODEM Command error
Mar 26 19:08:54.40: [ 3607]: <-- [9:AT+FRH=3\r]
Mar 26 19:08:58.15: [ 3607]: --> [7:CONNECT]
Mar 26 19:08:59.41: [ 3607]: --> [2:OK]
Mar 26 19:08:59.41: [ 3607]: REMOTE wants 7200 bit/s
Mar 26 19:08:59.41: [ 3607]: REMOTE wants A4 page width (215 mm)
Mar 26 19:08:59.42: [ 3607]: REMOTE wants unlimited page length
Mar 26 19:08:59.42: [ 3607]: REMOTE wants 3.85 line/mm
Mar 26 19:08:59.42: [ 3607]: REMOTE wants 2-D MR
Mar 26 19:08:59.42: [ 3607]: RECV training at v.29 7200 bit/s
Mar 26 19:08:59.42: [ 3607]: <-- [10:AT+FRM=72\r]
Mar 26 19:08:59.97: [ 3607]: --> [7:CONNECT]
Mar 26 19:09:01.50: [ 3607]: RECV: TCF 1382 bytes, 0% non-zero, 1364 zero-run
Mar 26 19:09:01.51: [ 3607]: --> [10:NO CARRIER]
Mar 26 19:09:01.51: [ 3607]: <-- [9:AT+FRS=7\r]
Mar 26 19:09:01.56: [ 3607]: --> [5:ERROR]
Mar 26 19:09:01.56: [ 3607]: MODEM Command error
Mar 26 19:09:01.56: [ 3607]: <-- [9:AT+FRH=3\r]
Mar 26 19:09:04.81: [ 3607]: --> [7:CONNECT]
Mar 26 19:09:06.07: [ 3607]: --> [2:OK]
Mar 26 19:09:06.07: [ 3607]: REMOTE wants 7200 bit/s
Mar 26 19:09:06.07: [ 3607]: REMOTE wants A4 page width (215 mm)
Mar 26 19:09:06.08: [ 3607]: REMOTE wants unlimited page length
Mar 26 19:09:06.08: [ 3607]: REMOTE wants 3.85 line/mm
Mar 26 19:09:06.08: [ 3607]: REMOTE wants 2-D MR
Mar 26 19:09:06.08: [ 3607]: RECV training at v.29 7200 bit/s
Mar 26 19:09:06.08: [ 3607]: <-- [10:AT+FRM=72\r]
Mar 26 19:09:06.63: [ 3607]: --> [7:CONNECT]
Mar 26 19:09:08.16: [ 3607]: RECV: TCF 1382 bytes, 0% non-zero, 1364 zero-run
Mar 26 19:09:08.17: [ 3607]: --> [10:NO CARRIER]
Mar 26 19:09:08.17: [ 3607]: <-- [9:AT+FRS=7\r]
Mar 26 19:09:08.22: [ 3607]: --> [5:ERROR]
Mar 26 19:09:08.22: [ 3607]: MODEM Command error
Mar 26 19:09:08.22: [ 3607]: <-- [9:AT+FRH=3\r]
Mar 26 19:09:11.98: [ 3607]: --> [7:CONNECT]
Mar 26 19:09:13.24: [ 3607]: --> [2:OK]
Mar 26 19:09:13.24: [ 3607]: REMOTE wants 4800 bit/s
Mar 26 19:09:13.24: [ 3607]: REMOTE wants A4 page width (215 mm)
Mar 26 19:09:13.24: [ 3607]: REMOTE wants unlimited page length
Mar 26 19:09:13.25: [ 3607]: REMOTE wants 3.85 line/mm
Mar 26 19:09:13.25: [ 3607]: REMOTE wants 2-D MR
Mar 26 19:09:13.25: [ 3607]: RECV training at v.27ter 4800 bit/s
Mar 26 19:09:13.25: [ 3607]: <-- [10:AT+FRM=48\r]
Mar 26 19:09:14.28: [ 3607]: --> [7:CONNECT]
Mar 26 19:09:15.81: [ 3607]: RECV: TCF 915 bytes, 0% non-zero, 908 zero-run
Mar 26 19:09:15.82: [ 3607]: --> [10:NO CARRIER]
Mar 26 19:09:15.82: [ 3607]: <-- [9:AT+FRS=7\r]
Mar 26 19:09:15.86: [ 3607]: --> [5:ERROR]
Mar 26 19:09:15.86: [ 3607]: MODEM Command error
Mar 26 19:09:15.86: [ 3607]: <-- [9:AT+FRH=3\r]
Mar 26 19:09:19.11: [ 3607]: --> [7:CONNECT]
Mar 26 19:09:20.36: [ 3607]: --> [2:OK]
Mar 26 19:09:20.36: [ 3607]: REMOTE wants 4800 bit/s
Mar 26 19:09:20.36: [ 3607]: REMOTE wants A4 page width (215 mm)
Mar 26 19:09:20.37: [ 3607]: REMOTE wants unlimited page length
Mar 26 19:09:20.37: [ 3607]: REMOTE wants 3.85 line/mm
Mar 26 19:09:20.37: [ 3607]: REMOTE wants 2-D MR
Mar 26 19:09:20.37: [ 3607]: RECV training at v.27ter 4800 bit/s
Mar 26 19:09:20.37: [ 3607]: <-- [10:AT+FRM=48\r]
Mar 26 19:09:21.41: [ 3607]: --> [7:CONNECT]
Mar 26 19:09:22.94: [ 3607]: RECV: TCF 915 bytes, 0% non-zero, 908 zero-run
Mar 26 19:09:22.95: [ 3607]: --> [10:NO CARRIER]
Mar 26 19:09:22.95: [ 3607]: <-- [9:AT+FRS=7\r]
Mar 26 19:09:23.00: [ 3607]: --> [5:ERROR]
Mar 26 19:09:23.00: [ 3607]: MODEM Command error
Mar 26 19:09:23.00: [ 3607]: <-- [9:AT+FRH=3\r]
Mar 26 19:09:26.23: [ 3607]: --> [7:CONNECT]
Mar 26 19:09:27.49: [ 3607]: --> [2:OK]
Mar 26 19:09:27.49: [ 3607]: REMOTE wants 4800 bit/s
Mar 26 19:09:27.49: [ 3607]: REMOTE wants A4 page width (215 mm)
Mar 26 19:09:27.50: [ 3607]: REMOTE wants unlimited page length
Mar 26 19:09:27.50: [ 3607]: REMOTE wants 3.85 line/mm
Mar 26 19:09:27.50: [ 3607]: REMOTE wants 2-D MR
Mar 26 19:09:27.50: [ 3607]: RECV training at v.27ter 4800 bit/s
Mar 26 19:09:27.50: [ 3607]: <-- [10:AT+FRM=48\r]
Mar 26 19:09:28.53: [ 3607]: --> [7:CONNECT]
Mar 26 19:09:30.06: [ 3607]: RECV: TCF 915 bytes, 0% non-zero, 908 zero-run
Mar 26 19:09:30.07: [ 3607]: --> [10:NO CARRIER]
Mar 26 19:09:30.07: [ 3607]: <-- [9:AT+FRS=7\r]
Mar 26 19:09:30.12: [ 3607]: --> [5:ERROR]
Mar 26 19:09:30.12: [ 3607]: MODEM Command error
Mar 26 19:09:30.12: [ 3607]: <-- [9:AT+FRH=3\r]
Mar 26 19:09:33.87: [ 3607]: --> [7:CONNECT]
Mar 26 19:09:35.02: [ 3607]: --> [2:OK]
Mar 26 19:09:35.02: [ 3607]: RECV FAX: RSPREC error/got DCN
Mar 26 19:09:35.03: [ 3607]: RECV FAX: end
Mar 26 19:09:35.03: [ 3607]: SESSION END
|
Hylafax настроена нормально (второй модем USR Courier с конфигом для него нормально работает) та что дело явно в конфигурационном файле именно модема IDC-1914BXL. Если есть у кого рабочий конфиг Hylafax для этого модема поделитесь плиз или хотя бы направьте куда рыть ... вот конфиг что Hylafax ему сделала в автомате:
| Код: |
cat ./config.ttyS0
# $Id: class1,v 1.17 2006/07/21 08:46:17 aidan Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#
#
# Generic Class 1 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode: 7
AreaCode: 495
FAXNumber: +7.495.123.4567
LongDistancePrefix: 0
InternationalPrefix: 00
DialStringRules: etc/dialrules
ServerTracing: 1
SessionTracing: 11
RecvFileMode: 0644
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-h %l dx_%s"
LocalIdentifier: "NothingSetup"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
PercentGoodLines: 90
MaxConsecutiveBadLines: 10
MaxRecvPages: 25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class1 # use this to supply a hint
#ModemRate: 19200 # rate for DCE-DTE communication
#ModemFlowControl: xonxoff # XON/XOFF flow control assumed
#
#ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
#ModemSetupDCDCmd: AT&C1 # setup so DCD follows carrier
#GettyArgs: "-h %l dx_%s" # modem must auto-detect fax/data
#
# We can append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer. This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
# put it in the ModemDialCmd; e.g. "DT9%s@".
#
#ModemDialCmd: ATDT%s # T for tone dialing
#
# Other possible configuration stuff. The default strings are
# shown below. Only those that are different from the defaults
# need to be included in the configuration file.
#
#ModemResetCmds: "" # stuff to do when modem is reset
#ModemAnswerCmd: ATA # use this to answer phone
#ModemNoFlowCmd: AT&K # disable flow control cmd
#ModemHardFlowCmd: AT&K3 # hardware flow control cmd
#ModemSoftFlowCmd: AT&K4 # software flow control cmd
#ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd: ATE0 # disable command echo
#ModemVerboseResultsCmd: ATV1 # enable verbose command results
#ModemResultCodesCmd: ATQ0 # enable result codes
#ModemOnHookCmd: ATH0 # place phone on hook (hangup)
#ModemSoftResetCmd: ATZ # do soft reset of modem
#ModemSoftResetCmdDelay: 3000 # pause after soft reset
#ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier
#ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds
#ModemRecvFillOrder: LSB2MSB # bit order of received facsimile
#ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit
#
Class1Cmd: AT+FCLASS=1 # command to enter class 1
Class1PPMWaitCmd: AT+FTS=7 # command to stop and wait before PPM
Class1TCFWaitCmd: AT+FTS=7 # command to stop and wait before TCF
Class1EOPWaitCmd: AT+FTS=9 # command to stop and wait before EOP
Class1SwitchingCmd: AT+FRS=7 # silence between HDLC recv and trans
Class1TrainingRecovery: 1500 # 1.5sec delay after training failure
Class1RecvAbortOK: 200 # wait 200ms for abort response
Class1FrameOverhead: 4 # 4 byte overhead in recvd HDLC frames
Class1RecvIdentTimer: 40000 # 35+5secs waiting for ident frames
Class1TCFMaxNonZero: 10 # max 10% of data may be non-zero
Class1TCFMinRun: 1000 # min run is 2/3rds of TCF duration
|
Заранее благодарен за ответ! |
|
| Вернуться к началу |
|
 |
Technical Support
Expert
Зарегистрирован: 31.10.2002
Сообщения: 6330
|
| Добавлено: Чт Мар 27, 2008 10:44 am Заголовок сообщения: |
|
|
Попробуйте закомментировать эту команду:
# Class1SwitchingCmd: AT+FRS=7 # silence between HDLC recv and trans
или замените её на пустую:
Class1SwitchingCmd: AT # silence between HDLC recv and trans
_________________
Inpro
Technical Support |
|
| Вернуться к началу |
|
|
Mirage
Junior member
Зарегистрирован: 27.03.2008
Сообщения: 2
|
| Добавлено: Чт Мар 27, 2008 11:18 am Заголовок сообщения: |
|
|
| Technical Support писал(а): | Попробуйте закомментировать эту команду:
# Class1SwitchingCmd: AT+FRS=7 # silence between HDLC recv and trans
или замените её на пустую:
Class1SwitchingCmd: AT # silence between HDLC recv and trans |
Если закоментировать то изменений нет, а замена на пустую (АТ) помогла все заработало ... Огромное спасибо! |
|
| Вернуться к началу |
|
|
Technical Support
Expert
Зарегистрирован: 31.10.2002
Сообщения: 6330
|
| Добавлено: Пт Мар 28, 2008 12:03 am Заголовок сообщения: |
|
|
Ну что же, на этом и остановимся 
_________________
Inpro
Technical Support |
|
| Вернуться к началу |
|
|
|
|
Вы не можете начинать темы
Вы не можете отвечать на сообщения
Вы не можете редактировать свои сообщения
Вы не можете удалять свои сообщения
Вы не можете голосовать в опросах
|
Powered by phpBB © 2001, 2005 phpBB Group
|
FAQ
Поиск
Пользователи
Группы
Регистрация
Профиль
Войти и проверить личные сообщения
Вход
