Почти работает IDC-5614BXL/VR+ (Plus)

[Andrey1975]

Знакомые отдали этот модем, но что то у него не получается дружить с моими провайдерами, с одним вообще не хочет соединятся, сначала попищат друг другу и удаленный модем бросает трубку, а мой еще с минуту пытается соединиться с короткими гудками в линии, с другим провайдером соединяется, но постоянные ретрейны, обрывы, одним словом невозможно работать. Ниже привожу статистику последнего соединения качал файл размером 2 Мб, Пожалуйста подскажите можно ли как то поправить дело или все безнадежно плохо

Inpro IDC Modems Diagnostics, Version: 1.1.4.39
06.08.2007 12:58:02 - Direct Log Write Entry
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.26
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: M4

Time Online.................. 00:53:55
Termination Reason........... LINK DISCONNECT
Tx Rate (Last/Init/Min/Max).. 24000/21600/ 9600/24000 bps
Rx Rate (Last/Init/Min/Max).. 28000/38667/28000/42667 bps
Modulation................... V.90
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 3
Tx/Power Drop/Rx Level....... 15/1/18
SNR Last/Min/Max............. 41/29/43
Highest Rx/Tx State.......... 67/87
EQM Sum...................... 011E
RBS Pattern.................. 00
Rate Drop.................... 1
Digital Loss................. 2000
Retrains Issued/Granted/Auto. 0/0/39
Renegs Issued/Granted........ 54/5
FForwards/FBacks/FEQM/Denied. 4/50/48/0
Forced FB/FB after FF/MaxREJ. 16/30/11
Last dialed number........... P766-70-66
V90


Negotiation Result (Rx/Tx)... V.90 Issue 1 (asymmetric)/V.34
Symbol Rate (Rx/Tx).......... 8000/3200
Carrier Frequency Hz, Tx..... 1920
EQM Value (Last/Min/Max)..... 3/0/127
EQM Hits..................... 0
EQM Last 10 Readings......... 4 3 3 3 3 3 3 3 2 4
Fast Retrains (RRWS) Count... 102
Last Retrain/Reneg Status.... Local Fast Retrain
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 1 minutes ago
Handshake Time/Retries....... 21 seconds/0
Non-linear Encoding, Rx/Tx... OFF/OFF
Precoding, Rx/Tx............. OFF/OFF
Shaping, Rx/Tx............... OFF/OFF
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 6
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 6,9
Last Rx/Tx State............. 65/87
Energy at 3750Hz/Average .... 1973/1147
Auto Gain Amplitude, db...... 10
Rx Level (Last/Min/Max), -dB. 17,6/17,6/17,6
Detection of 120 Hz Tones.... Yes
Detection of Dual PCM........ No
V.90 RBS Pattern............. 00
V.90 Alternating RBS Pattern. 00
V.90 Digital Pad Value, db... 0,0
V.90 Optimal Speed........... 37333 bps (Reg.S120=
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. SYNC UA:T UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/204
Frames Errors, Rx/Tx......... 3020/384 (3,5%/3,7%)
Frames Count, Rx/Tx.......... 87498/10243
Error Control Frame Size..... V.42 LAPM (64)
Error Control Timeouts....... 218
Error Control Link NAKs...... 128
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 3 189 625
Characters Sent.............. 398 739
Average CPS, Rx/Tx........... 985/123
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 59

[Technical Support]

Пропишите в строке инициализации в свойствах модема такие команды:

S91=15 S210.7=1 +MS=11

и покажите, что получается в статистике.
_________________
Inpro
Technical Support

[Andrey1975]

Спасибо что откликнулись вот стаистика

Inpro IDC Modems Diagnostics, Version: 1.1.4.39
06.08.2007 14:18:20 - Outbound Call By RemoteAccess
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.26
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: M4

Time Online.................. 00:10:39
Termination Reason........... KEY ABORT
Tx Rate (Last/Init/Min/Max).. 21600/ 9600/ 9600/21600 bps
Rx Rate (Last/Init/Min/Max).. 4800/28800/ 4800/33600 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 0
Tx/Power Drop/Rx Level....... 15/0/NA
SNR Last/Min/Max............. 32/32/43
Highest Rx/Tx State.......... 67/87
EQM Sum...................... 001C
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 6/8/1
Renegs Issued/Granted........ 30/1
FForwards/FBacks/FEQM/Denied. 4/32/0/0
Forced FB/FB after FF/MaxREJ. 30/8/10
Last dialed number........... P766-70-66
Flex fail


Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 3429
Carrier Frequency Hz, Rx/Tx.. 1959/1959
EQM Value (Last/Min/Max)..... 0/0/127
EQM Hits..................... 0
EQM Last 10 Readings......... 0 0 0 0 0 0 0 0 0 0
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 15 seconds/0
Non-linear Encoding, Rx/Tx... OFF/OFF
Precoding, Rx/Tx............. ON/OFF
Shaping, Rx/Tx............... ON/OFF
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 7
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 6,7
Last Rx/Tx State............. 67/87
Energy at 3750Hz/Average .... 2058/1176
Rx Level (Last/Min/Max), -dB. NA/47,9/12,7d
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 28/113
Frames Errors, Rx/Tx......... 369/35 (3,0%/3,8%)
Frames Count, Rx/Tx.......... 12176/927
Error Control Frame Size..... V.42 LAPM (64)
Error Control Timeouts....... 22
Error Control Link NAKs...... 35
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 476 987
Characters Sent.............. 14 789
Average CPS, Rx/Tx........... 746/23
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 84

[Technical Support]

Очень интересно... а давайте попробуем заменить строку на такую:

S91=15 S210.7=1 S210.4=1 +MS=11,,,,,,9600

Что получается?
_________________
Inpro
Technical Support

[Andrey1975]

качал файл 1 мб и вот что получилось

Inpro IDC Modems Diagnostics, Version: 1.1.4.39
06.08.2007 17:19:32 - Outbound Call By RemoteAccess
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.26
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: S91=15 S210.7=1 +MS=11

Time Online.................. 00:09:12
Termination Reason........... LINK DISCONNECT
Tx Rate (Last/Init/Min/Max).. 9600/ 9600/ 9600/ 9600 bps
Rx Rate (Last/Init/Min/Max).. 33600/33600/33600/33600 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 34
Tx/Power Drop/Rx Level....... 15/0/22
SNR Last/Min/Max............. 43/43/43
Highest Rx/Tx State.......... 67/67
EQM Sum...................... 0030
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 0/0
FForwards/FBacks/FEQM/Denied. 0/0/0/0
Forced FB/FB after FF/MaxREJ. 0/0/0
Last dialed number........... P766-70-66
Flex fail


Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 3429
Carrier Frequency Hz, Rx/Tx.. 1959/1959
EQM Value (Last/Min/Max)..... 34/30/49
EQM Hits..................... 0
EQM Last 10 Readings......... 31 35 37 34 38 37 35 33 33 33
Last Retrain/Reneg Status.... None
Last Retrain/Reneg Reason.... None
Last Retrain/Reneg Time...... 9 minutes ago
Handshake Time/Retries....... 16 seconds/0
Non-linear Encoding, Rx/Tx... ON/OFF
Precoding, Rx/Tx............. ON/OFF
Shaping, Rx/Tx............... ON/OFF
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 7
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 7,2
Last Rx/Tx State............. 67/67
Energy at 3750Hz/Average .... 2054/1192
Rx Level (Last/Min/Max), -dB. 21,6/21,6/21,6
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:T UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/94
Frames Errors, Rx/Tx......... 862/17 (2,9%/1,0%)
Frames Count, Rx/Tx.......... 29325/1641
Error Control Frame Size..... V.42 LAPM (64)
Error Control Timeouts....... 1
Error Control Link NAKs...... 17
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 1 120 352
Characters Sent.............. 16 885
Average CPS, Rx/Tx........... 2029/30
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 65

[Technical Support]

Вот так и оставим, лучшего уже не добиться. Если для Вас важна быстрая отсылка почты и т.п. работы, требующие большого исходящего траффика, то поиграйте с ограничением скорости передачи (сейчас она ограничена 9600 бит/с). Увеличивайте её до тех пор, пока не начнутся перетренировки по инициативе удалённого модема (Retrains / Granted).
_________________
Inpro
Technical Support