настойка 5614

[beatle]

помогите настроить модем

Inpro IDC Modems Diagnostics, Version: 1.1.4.39
03.06.2006 1:40:59 - Clipboard Copy
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.26
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: S106=30 S107=45

Time Online.................. 00:12:23
Termination Reason........... RETRAIN FAILURE
Tx Rate (Last/Init/Min/Max).. 26400/26400/26400/26400 bps
Rx Rate (Last/Init/Min/Max).. 37333/38667/37333/38667 bps
Modulation................... V.90
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 37
Tx/Power Drop/Rx Level....... 15/0/NA
SNR Last/Min/Max............. 39/36/39
Highest Rx/Tx State.......... 65/87
EQM Sum...................... 010B
RBS Pattern.................. 00
Rate Drop.................... 0
Digital Loss................. 2000
Retrains Issued/Granted/Auto. 0/2/1
Renegs Issued/Granted........ 2/0
FForwards/FBacks/FEQM/Denied. 0/2/2/0
Forced FB/FB after FF/MaxREJ. 0/0/2
Last dialed number........... P690222
V90 9481834347E5


Negotiation Result (Rx/Tx)... V.90 Issue 1 (asymmetric)/V.34
Symbol Rate (Rx/Tx).......... 8000/3200
Carrier Frequency Hz, Tx..... 1829
EQM Value (Last/Min/Max)..... 37/23/43
EQM Hits..................... 0
EQM Last 10 Readings......... 39 35 38 37 38 33 43 33 30 34
Fast Retrains (RRWS) Count... 0
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 1 minutes ago
Handshake Time/Retries....... 25 seconds/0
Non-linear Encoding, Rx/Tx... OFF/ON
Precoding, Rx/Tx............. OFF/ON
Shaping, Rx/Tx............... OFF/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 2
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 6,0
Last Rx/Tx State............. 2C/2C
Energy at 3750Hz/Average .... 3363/1802
Auto Gain Amplitude, db...... 10
Rx Level (Last/Min/Max), -dB. NA/16,8/16,8d
Detection of 120 Hz Tones.... Yes
Detection of Dual PCM........ No
V.90 RBS Pattern............. 00
V.90 Alternating RBS Pattern. 00
V.90 Digital Pad Value, db... 0,0
V.90 Optimal Speed........... No Limit (Reg.S120=0)
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 03
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Server (Digital)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Workaround Used.............. Rate Reneg Failure (At 64 or 84)
Workaround Used.............. ABCODE check (Machine Gun Noise)
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 0/6
Frames Errors, Rx/Tx......... 6/2 (0,1%/0,1%)
Frames Count, Rx/Tx.......... 8619/3573
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 13
Error Control Link NAKs...... 2
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 1 653 601
Characters Sent.............. 254 172
Average CPS, Rx/Tx........... 2225/342
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 91

ы пожалуйста проаналызируте лог, я в етом новичок, что нужно зделать или переделать?

[Technical Support]

В общем-то, всё более-менее соответствует ситуации (работа на V.90 через аналоговую АТС).

Что касается строки инициализации, то попробуйте такую:

S106=30 S107=45 M4 +MS=,,,,,,21600

Теперь модем будет включать динамик во время пересогласований скорости и перетренировок. Если произойдёт обрыв соединения, то хотелось бы узнать, что Вы слышали в динамике непосредственно перед разрывом. Например, "короткие гудки на фоне писка моего модема".
_________________
Inpro
Technical Support

[beatle]

Да так и было: шум, свист на фоне коротких гудков - а потом модем оборвал линию. А ето статистика за сеанс

Inpro IDC Modems Diagnostics, Version: 1.1.4.39
03.06.2006 12:50:39 - Clipboard Copy
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.26
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: S106=30 S107=45 M4 +MS=,,,,,,21600

Time Online.................. 00:04:48
Termination Reason........... RETRAIN FAILURE
Tx Rate (Last/Init/Min/Max).. 21600/21600/21600/21600 bps
Rx Rate (Last/Init/Min/Max).. 33333/38667/33333/38667 bps
Modulation................... V.90
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 44
Tx/Power Drop/Rx Level....... 15/0/NA
SNR Last/Min/Max............. 36/36/37
Highest Rx/Tx State.......... 65/87
EQM Sum...................... 0105
RBS Pattern.................. 00
Rate Drop.................... 0
Digital Loss................. 2000
Retrains Issued/Granted/Auto. 0/0/2
Renegs Issued/Granted........ 12/0
FForwards/FBacks/FEQM/Denied. 2/10/8/0
Forced FB/FB after FF/MaxREJ. 0/1/1
Last dialed number........... P690222
V90 9481834347E5


Negotiation Result (Rx/Tx)... V.90 Issue 1 (asymmetric)/V.34
Symbol Rate (Rx/Tx).......... 8000/3200
Carrier Frequency Hz, Tx..... 1829
EQM Value (Last/Min/Max)..... 44/13/126
EQM Hits..................... 0
EQM Last 10 Readings......... 42 44 45 45 21 20 28 19 19 24
Fast Retrains (RRWS) Count... 3
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 25 seconds/0
Non-linear Encoding, Rx/Tx... OFF/ON
Precoding, Rx/Tx............. OFF/ON
Shaping, Rx/Tx............... OFF/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 1
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 6,0
Last Rx/Tx State............. 21/20
Energy at 3750Hz/Average .... 3261/1749
Auto Gain Amplitude, db...... 10
Rx Level (Last/Min/Max), -dB. NA/16,8/16,8d
Detection of 120 Hz Tones.... Yes
Detection of Dual PCM........ No
V.90 RBS Pattern............. 00
V.90 Alternating RBS Pattern. 00
V.90 Digital Pad Value, db... 0,0
V.90 Optimal Speed........... No Limit (Reg.S120=0)
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 03
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Server (Digital)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Workaround Used.............. V90 Phase 2 Escape
Workaround Used.............. Rate Reneg Failure (At 64 or 84)
Workaround Used.............. V34 Codex WA/V34 Stuck Phase2
Workaround Used.............. ABCODE check (Machine Gun Noise)
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 0/2
Frames Errors, Rx/Tx......... 2/0 (4,3%/0,0%)
Frames Count, Rx/Tx.......... 47/24
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 1
Error Control Link NAKs...... 0
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 2 131
Characters Sent.............. 1 214
Average CPS, Rx/Tx........... 7/4
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 88

А еще за ети несколько минут я слышал около 4-5 шипений, ето перетренировки?
Почему он сам выключаеться?

[Technical Support]

Похоже, пользоваться V.90 не удастся. Попробуйте в строке инициализации заменить команду +MS на такую:

+MS=11,,,,,,21600

и покажите, что получается в статистике.
_________________
Inpro
Technical Support

[beatle]

Inpro IDC Modems Diagnostics, Version: 1.1.4.39
06.06.2006 23:46:42 - Direct Log Write Entry
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.26
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: S106=30 S107=45 M4 +MS=11,,,,,,21600

Time Online.................. 00:14:41
Termination Reason........... RETRAIN FAILURE
Tx Rate (Last/Init/Min/Max).. 21600/21600/21600/21600 bps
Rx Rate (Last/Init/Min/Max).. 31200/33600/31200/33600 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 126
Tx/Power Drop/Rx Level....... 9/2/NA
SNR Last/Min/Max............. 36/36/37
Highest Rx/Tx State.......... 22/20
EQM Sum...................... 0041
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/1/1
Renegs Issued/Granted........ 2/0
FForwards/FBacks/FEQM/Denied. 0/2/0/0
Forced FB/FB after FF/MaxREJ. 1/0/7
Last dialed number........... P690222
Flex fail


Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 3429
Carrier Frequency Hz, Rx/Tx.. 1959/1959
EQM Value (Last/Min/Max)..... 126/37/127
EQM Hits..................... 0
EQM Last 10 Readings......... 126 126 127 127 127 127 45 49 39 41
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 19 seconds/0
Non-linear Encoding, Rx/Tx... ON/ON
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 2
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 6,1
Last Rx/Tx State............. 22/20
Energy at 3750Hz/Average .... 5622/3036
Rx Level (Last/Min/Max), -dB. NA/25,7/25,7d
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Workaround Used.............. ABCODE check (Machine Gun Noise)
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 0/63
Frames Errors, Rx/Tx......... 63/2 (0,4%/0,0%)
Frames Count, Rx/Tx.......... 16069/5745
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 8
Error Control Link NAKs...... 2
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 3 269 054
Characters Sent.............. 425 766
Average CPS, Rx/Tx........... 3710/483
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 88

[Technical Support]

Ну что же, картина гораздо более приятная. Неприятный момент - разрыв связи, но если судить по статистике, то с этим мы ничего сделать не сможем. Нам представляется так, что происходит разрыв телефонного соединения. "На слух" это выглядит так: включается динамик, и слышны короткие гудки на фоне "писка" Вашего модема. Всё это продолжается 15..30 сек, после чего модем отключается (ждать нечего, с другой стороны модема уже нет, не с кем восстанавливать соединение).

Если всё именно так, то Вам нужно сообщить о проблеме провайдеру и/или работникам АТС. Возможно, им удастся исправить ситуацию.

Что касается строки инициализации, то дополните её командами:

S91=15 S210.7=1
_________________
Inpro
Technical Support