| Предыдущая тема :: Следующая тема |
| Автор |
Сообщение |
Alex P.
Associated member
Зарегистрирован: 15.11.2004
Сообщения: 6
|
 Добавлено: Вс Авг 21, 2005 9:51 pm Заголовок сообщения: Не проходят данные при связи между 2-мя модемами. |
 |
|
При связи между домашним компьютером и компьютером на рабочем месте устанавливается соединение в 21-26 кбс, но при этом не проходят никакие данные. Я просил совета у техподдержки в мае - посоветовали, помогли. Тогда было так, на удаленной машине стоял 3COM USR2976, а меня IDC5614BXL/VR+, посоветовали там следующую строку инициализации: там - ATS91=6, у меня AT S202.3=1 S210.7=1 S91=9. Все стало хорошо. Но проблема вернулась и с июля не могу поработать с удаленной машиной. Теперь там, дополнительно, стоит и IDC5614BXL/VR+, такой же как дома. Если связываться с одной рабочей с другой рабочей в любой комбинации (внутри лаборатории), то все хорошо - соединение 33 кбс, данные текут ровно, сильно, а вот из дома, то просто беда, пробовал уменьшать-увеличивать вых. сигнал там и здесь, но совсем не помогает. При этом с обычным провайдером на V90 с 37-40 кбс без особых трудностей. Да, телефонная линия у меня спаренная.
Вот последние статистики:
На удаленной стороне IDC-5614BXL/VR+ (Plus):
| Код: |
Inpro IDC Modems Diagnostics, Version: 1.1.4.39
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.26
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: AT S13.7=1 S202.3=1 S210.7=1 S91=9 \N3 %C3 %E3
Termination Reason........... NO REMOTE RESPONSE
Tx Rate (Last/Init/Min/Max).. 14400/21600/14400/21600 bps
Rx Rate (Last/Init/Min/Max).. 16800/21600/16800/21600 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 36
Tx/Power Drop/Rx Level....... 9/0/31
SNR Last/Min/Max............. 31/31/31
Highest Rx/Tx State.......... 63/87
EQM Sum...................... 017F
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/1/0
Renegs Issued/Granted........ 0/2
FForwards/FBacks/FEQM/Denied. 0/0/0/0
Forced FB/FB after FF/MaxREJ. 0/0/1
Flex fail 94818303
Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 3200
Carrier Frequency Hz, Rx/Tx.. 1829/1829
EQM Value (Last/Min/Max)..... 36/12/127
EQM Hits..................... 0
EQM Last 10 Readings......... 24 39 46 14 13 16 24 19 16 13
Last Retrain/Reneg Status.... Remote Retrain
Last Retrain/Reneg Reason.... Remote Retrain
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 51 seconds/0
Non-linear Encoding, Rx/Tx... ON/ON
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 5
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 0,7
Last Rx/Tx State............. 63/63
Energy at 3750Hz/Average .... 4/1
Rx Level (Last/Min/Max), -dB. 30,5/40,1/30,5
Detection of 120 Hz Tones.... No
Detection of Dual PCM........ No
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/No/No/No/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 03
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Client (Analog)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 4/1
Frames Errors, Rx/Tx......... 1/3 (2,9%/3,6%)
Frames Count, Rx/Tx.......... 35/84
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 4
Error Control Link NAKs...... 3
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 1 357
Characters Sent.............. 5 734
Average CPS, Rx/Tx........... 14/62
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 62
Inpro IDC Modems Diagnostics, Version: 1.1.4.39
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.26
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: AT S13.7=1 S202.3=1 S210.7=1 S91=15 \N5 %C0
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 7200/ 9600/ 7200/ 9600 bps
Rx Rate (Last/Init/Min/Max).. 14400/14400/14400/14400 bps
Modulation................... V.34bis
Protocol/Compression......... MNP/NONE
Line Quality................. 13
Tx/Power Drop/Rx Level....... 15/0/39
SNR Last/Min/Max............. 27/27/27
Highest Rx/Tx State.......... 85/87
EQM Sum...................... 0000
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 1/0
FForwards/FBacks/FEQM/Denied. 0/0/0/0
Forced FB/FB after FF/MaxREJ. 0/0/0
Flex fail 94818303
Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 2400
Carrier Frequency Hz, Rx/Tx.. 1600/1600
EQM Value (Last/Min/Max)..... 13/10/35
EQM Hits..................... 0
EQM Last 10 Readings......... 20 14 17 13 13 17 14 25 16 10
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Rate Renegotiation due to MNP10
Last Retrain/Reneg Time...... 2 minutes ago
Handshake Time/Retries....... 53 seconds/0
Non-linear Encoding, Rx/Tx... ON/OFF
Precoding, Rx/Tx............. OFF/OFF
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 4
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 0,6
Last Rx/Tx State............. 85/87
Energy at 3750Hz/Average .... 6/1
Rx Level (Last/Min/Max), -dB. 37,9/37,9/37,9
Detection of 120 Hz Tones.... No
Detection of Dual PCM........ No
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/No/No/No/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 03
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Client (Analog)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. LA:T LA:R LR:T LR:R
Frames REJected, Last/Total.. 0/0
Frames Count, Rx/Tx.......... 0/0
Error Control Frame Size..... MNP (256)
Error Control Timeouts....... 0
Error Control Link NAKs...... 0
Compression Dictionary Size.. NONE (0)
Characters Received.......... 1 808
Characters Sent.............. 5 876
Average CPS, Rx/Tx........... 6/20
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 66
Inpro IDC Modems Diagnostics, Version: 1.1.4.39
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.26
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: AT S13.7=1 S202.3=1 S210.7=1 S91=15 \N5 %C0
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 7200/ 9600/ 7200/ 9600 bps
Rx Rate (Last/Init/Min/Max).. 14400/14400/14400/14400 bps
Modulation................... V.34bis
Protocol/Compression......... MNP/NONE
Line Quality................. 13
Tx/Power Drop/Rx Level....... 15/0/39
SNR Last/Min/Max............. 27/27/27
Highest Rx/Tx State.......... 85/87
EQM Sum...................... 0000
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 1/0
FForwards/FBacks/FEQM/Denied. 0/0/0/0
Forced FB/FB after FF/MaxREJ. 0/0/0
Flex fail 94818303
Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 2400
Carrier Frequency Hz, Rx/Tx.. 1600/1600
EQM Value (Last/Min/Max)..... 13/10/35
EQM Hits..................... 0
EQM Last 10 Readings......... 20 14 17 13 13 17 14 25 16 10
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Rate Renegotiation due to MNP10
Last Retrain/Reneg Time...... 2 minutes ago
Handshake Time/Retries....... 53 seconds/0
Non-linear Encoding, Rx/Tx... ON/OFF
Precoding, Rx/Tx............. OFF/OFF
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 4
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 0,6
Last Rx/Tx State............. 85/87
Energy at 3750Hz/Average .... 6/1
Rx Level (Last/Min/Max), -dB. 37,9/37,9/37,9
Detection of 120 Hz Tones.... No
Detection of Dual PCM........ No
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/No/No/No/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 03
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Client (Analog)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. LA:T LA:R LR:T LR:R
Frames REJected, Last/Total.. 0/0
Frames Count, Rx/Tx.......... 0/0
Error Control Frame Size..... MNP (256)
Error Control Timeouts....... 0
Error Control Link NAKs...... 0
Compression Dictionary Size.. NONE (0)
Characters Received.......... 1 808
Characters Sent.............. 5 876
Average CPS, Rx/Tx........... 6/20
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 66
Inpro IDC Modems Diagnostics, Version: 1.1.4.39
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.26
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: AT S13.7=1 S202.3=1 S210.7=1 S91=9
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 9600/16800/ 9600/16800 bps
Rx Rate (Last/Init/Min/Max).. 24000/24000/24000/24000 bps
Modulation................... V.34bis
Protocol/Compression......... MNP/NONE
Line Quality................. 61
Tx/Power Drop/Rx Level....... 15/0/40
SNR Last/Min/Max............. 32/32/32
Highest Rx/Tx State.......... 85/87
EQM Sum...................... 00F4
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 3/0
FForwards/FBacks/FEQM/Denied. 0/0/0/0
Forced FB/FB after FF/MaxREJ. 0/0/0
Flex fail 94818303
Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 3200
Carrier Frequency Hz, Rx/Tx.. 1829/1829
EQM Value (Last/Min/Max)..... 61/47/68
EQM Hits..................... 0
EQM Last 10 Readings......... 61 57 55 61 61 59 52 55 56 52
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Rate Renegotiation due to MNP10
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 53 seconds/0
Non-linear Encoding, Rx/Tx... ON/ON
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 5
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 0,7
Last Rx/Tx State............. 85/87
Energy at 3750Hz/Average .... 8/1
Rx Level (Last/Min/Max), -dB. 39,4/39,4/39,4
Detection of 120 Hz Tones.... No
Detection of Dual PCM........ No
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/No/No/No/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 03
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Client (Analog)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. LA:T LA:R LR:T LR:R
Frames REJected, Last/Total.. 0/0
Frames Count, Rx/Tx.......... 0/0
Error Control Frame Size..... MNP (256)
Error Control Timeouts....... 0
Error Control Link NAKs...... 0
Compression Dictionary Size.. NONE (0)
Characters Received.......... 1 151
Characters Sent.............. 6 665
Average CPS, Rx/Tx........... 7/41
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 72
|
На удаленной стороне 3COM USR2976:
| Код: |
Inpro IDC Modems Diagnostics, Version: 1.1.4.39
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.26
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: ATS13.7=1S91=12S210.7=1S202.3=1
Termination Reason........... RETRAIN FAILURE
Tx Rate (Last/Init/Min/Max).. 4800/14400/ 4800/14400 bps
Rx Rate (Last/Init/Min/Max).. 9600/19200/ 9600/21600 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 5
Tx/Power Drop/Rx Level....... 9/0/NA
SNR Last/Min/Max............. 41/29/41
Highest Rx/Tx State.......... 84/85
EQM Sum...................... 018C
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 1/1/9
Renegs Issued/Granted........ 1/9
FForwards/FBacks/FEQM/Denied. 0/2/0/0
Forced FB/FB after FF/MaxREJ. 1/1/7
Flex fail
Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 3200
Carrier Frequency Hz, Rx/Tx.. 1829/1829
EQM Value (Last/Min/Max)..... 5/2/127
EQM Hits..................... 0
EQM Last 10 Readings......... 2 10 13 12 9 8 5 5 6 5
Last Retrain/Reneg Status.... Remote Rate Renegotiation
Last Retrain/Reneg Reason.... Remote Rate Renegotiation
Last Retrain/Reneg Time...... 1 minutes ago
Handshake Time/Retries....... 49 seconds/0
Non-linear Encoding, Rx/Tx... OFF/ON
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 64 state
Pre-Emphasis Index, Tx....... 5
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 1,3
Last Rx/Tx State............. 22/20
Energy at 3750Hz/Average .... 8/0
Rx Level (Last/Min/Max), -dB. NA/42,4/40,5d
Detection of 120 Hz Tones.... No
Detection of Dual PCM........ No
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Workaround Used.............. V90 Phase 2 Escape
Workaround Used.............. Rate Reneg Failure (At 64 or 84)
Workaround Used.............. ABCODE check (Machine Gun Noise)
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 0/17
Frames Errors, Rx/Tx......... 17/2 (5,6%/1,0%)
Frames Count, Rx/Tx.......... 304/196
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 19
Error Control Link NAKs...... 2
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 8 289
Characters Sent.............. 6 416
Average CPS, Rx/Tx........... 29/22
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 93
Inpro IDC Modems Diagnostics, Version: 1.1.4.39
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.26
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: ATS13.7=1 S91=12 S210.7=1 S202.3=1
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 9600/ 4800/ 4800/16800 bps
Rx Rate (Last/Init/Min/Max).. 21600/24000/ 7200/24000 bps
Modulation................... V.34bis
Protocol/Compression......... NONE
Line Quality................. 25
Tx/Power Drop/Rx Level....... 12/0/39
SNR Last/Min/Max............. 43/29/43
Highest Rx/Tx State.......... 84/85
EQM Sum...................... 01AD
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/3/13
Renegs Issued/Granted........ 2/14
FForwards/FBacks/FEQM/Denied. 1/1/0/1
Forced FB/FB after FF/MaxREJ. 0/1/0
Flex fail
Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 3200
Carrier Frequency Hz, Rx/Tx.. 1829/1829
EQM Value (Last/Min/Max)..... 25/0/81
EQM Hits..................... 0
EQM Last 10 Readings......... 21 28 23 28 23 28 25 26 32 24
Last Retrain/Reneg Status.... Remote Rate Renegotiation
Last Retrain/Reneg Reason.... Remote Rate Renegotiation
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 48 seconds/0
Non-linear Encoding, Rx/Tx... ON/ON
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 64 state
Pre-Emphasis Index, Tx....... 5
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 1,3
Last Rx/Tx State............. 67/67
Energy at 3750Hz/Average .... 8/7
Rx Level (Last/Min/Max), -dB. 38,3/39,4/37,6
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Workaround Used.............. V90 Phase 2 Escape
Workaround Used.............. Rate Reneg Failure (At 64 or 84)
Error Correction Status Byte. ODP:T
Frames REJected, Last/Total.. 0/0
Frames Count, Rx/Tx.......... 0/0
Error Control Frame Size..... NONE (0)
Error Control Timeouts....... 0
Error Control Link NAKs...... 0
Compression Dictionary Size.. NONE (0)
Characters Received.......... 18 486
Characters Sent.............. 4 155
Average CPS, Rx/Tx........... 55/12
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 82
|
Вот как было в хорошие времена (На удаленной стороне 3COM USR2976):
| Код: |
Inpro IDC Modems Diagnostics, Версия 1.0.3.36
--------------------------------------------------------
Тип модема: IDC-5614BXL/VR+ (Plus) Версия прошивки: V2.26
Строка инициализации системная: AT&FS38=0S95=41S115=0E0<cr>
Строка инициализации пользователя: ATS13.7=1S17=64S91=8S120=15S210.7=0S202.3=1
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 21600/19200/ 4800/21600 bps
Rx Rate (Last/Init/Min/Max).. 19200/21600/12000/21600 bps
Modulation................... V.34bis
Protocol/Compression......... NONE
Line Quality................. 24
Tx/Power Drop/Rx Level....... 8/0/42
SNR Last/Min/Max............. 31/24/43
Highest Rx/Tx State.......... 84/87
EQM Sum...................... 0209
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 4/1/6
Renegs Issued/Granted........ 17/129
FForwards/FBacks/FEQM/Denied. 3/18/0/0
Forced FB/FB after FF/MaxREJ. 0/0/0
Flex fail
Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 3200
Carrier Frequency Hz, Rx/Tx.. 1829/1829
EQM Value (Last/Min/Max)..... 24/8/127
EQM Hits..................... 0
EQM Last 10 Readings......... 26 24 26 26 25 22 25 28 25 29
Last Retrain/Reneg Status.... Remote Rate Renegotiation
Last Retrain/Reneg Reason.... Remote Rate Renegotiation
Last Retrain/Reneg Time...... 1 minutes ago
Handshake Time/Retries....... 51 seconds/0
Non-linear Encoding, Rx/Tx... ON/ON
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 64 state
Pre-Emphasis Index, Tx....... 5
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 1,3
Last Rx/Tx State............. 67/87
Energy at 3750Hz/Average .... 8/1
AGC Gain (Last/Min/Max)...... 30/26/65
Detection of 120 Hz Tones.... No
Detection of Dual PCM........ No
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Frames REJected, Last/Total.. 0/0
Frames Count, Rx/Tx.......... 0/0
Error Control Frame Size..... NONE (0)
Error Control Timeouts....... 0
Error Control Link NAKs...... 0
Compression Dictionary Size.. NONE (0)
Characters Received.......... 6 082 855
Characters Sent.............. 628 410
Average CPS, Rx/Tx........... 382/39
Characters Lost, Rx/Tx....... 142/10579
Estimated Noise Level, -dBm.. 73
|
Извините за большие "простыни", но это для полноты информации. 
_________________
Alex S. Petro |
|
| Вернуться к началу |
|
 |
Technical Support
Expert
Зарегистрирован: 31.10.2002
Сообщения: 6330
|
| Добавлено: Вс Авг 21, 2005 10:18 pm Заголовок сообщения: |
|
|
Интересно... почему-то в статистике отсутствуют строчки "Time online". Вы из специально "выкусили"?
_________________
Inpro
Technical Support |
|
| Вернуться к началу |
|
|
Alex P.
Associated member
Зарегистрирован: 15.11.2004
Сообщения: 6
|
| Добавлено: Вс Авг 21, 2005 10:55 pm Заголовок сообщения: |
|
|
Ну так, вообщем-то, да.
В онлайне где-то, в среднем по 15 минут, но были и по 40, а последняя статистика около 4 часов. Я почти во всех случаях отключался сам, так как за два месяца одно и тоже хоть час, хоть пять минут.
_________________
Alex S. Petro |
|
| Вернуться к началу |
|
|
Technical Support
Expert
Зарегистрирован: 31.10.2002
Сообщения: 6330
|
| Добавлено: Пн Авг 22, 2005 8:53 am Заголовок сообщения: |
|
|
Выкусывать строчки из статистики смысла нет. Например, возьмём статистику в "хорошие времена":
Characters Received.......... 6 082 855
Average CPS, Rx/Tx........... 382/39
Длительность сеанса связи составила 6082855 / 382 / 60 = 265 минут, или 4 часа 25 минут.
Кстати, о "хороших временах". Модемам не использовали протокол коррекции ошибок:
Protocol/Compression......... NONE
Причём отсутствие протокола объясняется тем, что он был отключён в свойствах модема (если, конечно, не соответствующие строки не были убраны из статистики вручную). Так что хорошими эти времена назвать сложно...
Давайте вернёмся на исходные позиции. Запустите терминал и верните оба модема ("рабочий" и "домашний") в исходное положение командой:
at *nc22 w2 \v1 s95=3 &w &w1
OK
Теперь пропишите в строке инициализации обоих модемов команды:
S210.7=1 S91=6 S202.3=1 \N2
и покажите, что в такой ситуации получается в статистике. Не редактируйте статистику.
_________________
Inpro
Technical Support |
|
| Вернуться к началу |
|
|
|
|
Вы не можете начинать темы
Вы не можете отвечать на сообщения
Вы не можете редактировать свои сообщения
Вы не можете удалять свои сообщения
Вы не можете голосовать в опросах
|
Powered by phpBB © 2001, 2005 phpBB Group
|
FAQ
Поиск
Пользователи
Группы
Регистрация
Профиль
Войти и проверить личные сообщения
Вход
