IDC-5614BXL/VR+ помогите с настройками исходя из статистики

[gruve]

Здраствуйте
Модем IDC-5614BXL/VR+
Прошивка 2.24
Коннект к провайдеру был от 22 до 32 Kbps
В статистике пока не разбираюсь, но судя по строке Remote Protocol Support...... K56flex V.90, коннект может быть на большей скорости, если я не ошибаюсь...
Уважаемый ТехСаппорт, посмотрите, плиз, что можно сделать =)
Заранее спасибо!

Статистика:

Inpro IDC Modems Diagnostics, Version 1.0.2.33
16.04.2004 6:32:33 - Outbound Call by RemoteAccess
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.24

Time Online.................. 00:18:14
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 24000/21600/14400/24000 bps
Rx Rate (Last/Init/Min/Max).. 29333/32000/29333/32000 bps
Modulation................... V.90
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 127
Tx/Power Drop/Rx Level....... 15/0/16
SNR Last/Min/Max............. 37/37/43
Highest Rx/Tx State.......... 67/87
EQM Sum...................... 0146
RBS Pattern.................. 00
Rate Drop.................... 0
Digital Loss................. 2000
Retrains Issued/Granted/Auto. 0/1/0
Renegs Issued/Granted........ 14/6
FForwards/FBacks/Denied...... 5/9/0
Forced FB/FB after FF/MaxREJ. 9/4/10
Last dialed number........... P8W2850
V90 9481834246E0

Negotiation Result (Rx/Tx)... V.90 Issue 1 (asymmetric)/V.34
Symbol Rate (Rx/Tx).......... 8000/3200
Carrier Frequency Hz, Tx..... 1920
EQM Value (Last/Min/Max)..... 127/16/127
EQM Hits..................... 0
EQM Last 10 Readings......... 127 124 123 16 27 28 27 28 26 29
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 1 minutes ago
Handshake Time/Retries....... 22 seconds/0
Non-linear Encoding, Rx/Tx... OFF/OFF
Precoding, Rx/Tx............. OFF/OFF
Shaping, Rx/Tx............... OFF/OFF
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 2
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 1,9
Last Rx/Tx State............. 67/87
Energy at 3750Hz/Average .... 5033/1038
Auto Gain Amplitude, db...... 10
AGC Gain (Last/Min/Max)...... 96/96/96
Detection of 120 Hz Tones.... Yes
Detection of Dual PCM........ No
V.90 RBS Pattern............. 00
V.90 Alternating RBS Pattern. 00
V.90 Digital Pad Value, db... 0,0
V.90 Optimal Speed........... No Limit (Reg.S120=0)
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 02
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Server (Digital)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... External
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/32
Frames Errors, Rx/Tx......... 288/34 (2,0%/0,8%)
Frames Count, Rx/Tx.......... 14626/4533
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 69
Error Control Link NAKs...... 34
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 1 726 568
Characters Sent.............. 111 680
Average CPS, Rx/Tx........... 1578/102
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 53

[Technical Support]

Попробуйте поработать с такой строчкой инициализации:

S210.7=1 S91=15 S210.4=1 +MS=12,,,,,,14400

Затем поменяйте строчку на такую:

S210.7=1 S91=15 S210.4=1 +MS=11,,,,,,14400

и покажите статистики, полученную в каждом из случаев.
_________________
Inpro
Technical Support

[gruve]

Попробовал Ваши рекомендации...

Статистика c S210.7=1 S91=15 S210.4=1 +MS=12,,,,,,14400
(соединение было на 32 Kbps)

Inpro IDC Modems Diagnostics, Version 1.0.2.33
16.04.2004 17:25:18 - Outbound Call by RemoteAccess
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.24

Time Online.................. 00:10:34
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 12000/14400/12000/14400 bps
Rx Rate (Last/Init/Min/Max).. 28800/33333/26400/33333 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 36
Tx/Power Drop/Rx Level....... 15/0/16
SNR Last/Min/Max............. 43/41/43
Highest Rx/Tx State.......... 85/87
EQM Sum...................... 0089
RBS Pattern.................. 00
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 2/0/1
Renegs Issued/Granted........ 7/1
FForwards/FBacks/Denied...... 4/5/0
Forced FB/FB after FF/MaxREJ. 0/2/0
Last dialed number........... P8W2850
Flex fail

Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 3429
Carrier Frequency Hz, Rx/Tx.. 1959/1959
EQM Value (Last/Min/Max)..... 36/18/127
EQM Hits..................... 0
EQM Last 10 Readings......... 37 33 36 34 39 34 36 33 38 35
Last Retrain/Reneg Status.... Remote Rate Renegotiation
Last Retrain/Reneg Reason.... Remote Rate Renegotiation
Reason for V.34 Fallback..... Data Pump decision to Fallback
Last Retrain/Reneg Time...... 2 minutes ago
Handshake Time/Retries....... 17 seconds/0
Non-linear Encoding, Rx/Tx... ON/ON
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 3
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 1,7
Last Rx/Tx State............. 67/87
Energy at 3750Hz/Average .... 1773/98
Auto Gain Amplitude, db...... 10
AGC Gain (Last/Min/Max)...... 97/96/97
Detection of 120 Hz Tones.... Yes
Detection of Dual PCM........ No
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/131
Frames Errors, Rx/Tx......... 131/2 (2,4%/0,2%)
Frames Count, Rx/Tx.......... 5455/1163
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 20
Error Control Link NAKs...... 2
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 616 690
Characters Sent.............. 62 076
Average CPS, Rx/Tx........... 972/97
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 59



Статистика c S210.7=1 S91=15 S210.4=1 +MS=11,,,,,,14400
(соединение было на 26.4 Kbps, причем соединилось быстрее, но через минуту обрыв...
2ой раз тоже быстро уже на 28.8 Kbps)

Inpro IDC Modems Diagnostics, Version 1.0.2.33
16.04.2004 17:43:30 - Outbound Call by RemoteAccess
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.24

Time Online.................. 00:10:17
Termination Reason........... NO REMOTE RESPONSE
Tx Rate (Last/Init/Min/Max).. 14400/14400/14400/14400 bps
Rx Rate (Last/Init/Min/Max).. 31200/28800/24000/31200 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 124
Tx/Power Drop/Rx Level....... 15/0/9
SNR Last/Min/Max............. 31/31/41
Highest Rx/Tx State.......... 67/67
EQM Sum...................... 004A
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/1/0
Renegs Issued/Granted........ 4/0
FForwards/FBacks/Denied...... 2/2/0
Forced FB/FB after FF/MaxREJ. 0/0/0
Last dialed number........... P8W2850
Flex fail

Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 3429
Carrier Frequency Hz, Rx/Tx.. 1959/1959
EQM Value (Last/Min/Max)..... 124/11/127
EQM Hits..................... 0
EQM Last 10 Readings......... 126 126 124 123 51 48 50 52 52 61
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 12 seconds/0
Non-linear Encoding, Rx/Tx... ON/ON
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 3
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 1,7
Last Rx/Tx State............. 67/67
Energy at 3750Hz/Average .... 5402/1275
AGC Gain (Last/Min/Max)...... 116/59/116
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/61
Frames Errors, Rx/Tx......... 573/1 (4,9%/0,1%)
Frames Count, Rx/Tx.......... 11788/1628
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 13
Error Control Link NAKs...... 1
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 762 360
Characters Sent.............. 45 846
Average CPS, Rx/Tx........... 1235/74
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 40

[Technical Support]

Ну что же, остановимся на такой строке инициализации:

S210.7=1 S91=15 S210.4=1 S202.5=1 +MS=,,,,,,14400
_________________
Inpro
Technical Support

[gruve]

Спасибо, попробую...