Помогите настроить idc 5614 bxl/vr

[zmy]

Подскажите, что можно сделать? Раньше всегда коннект был 49000
На что грешить, на линию или настройки?

Time Online.................. 00:02:07
Termination Reason........... LINK DISCONNECT
Tx Rate (Last/Init/Min/Max).. 26400/26400/26400/26400 bps
Rx Rate (Last/Init/Min/Max).. 14400/21600/14400/21600 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 60
Tx/Power Drop/Rx Level....... 15/0/30
SNR Last/Min/Max............. 43/43/43
Highest Rx/Tx State.......... 85/87
EQM Sum...................... 01BA
RBS Pattern.................. 00
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 3/0
FForwards/FBacks/Denied...... 0/3/0
Forced FB/FB after FF/MaxREJ. 2/0/8
Last dialed number........... T20000
Flex fail 9481834347E8

Rockwell Diagnostics/W32, version 1.1.0.6, compiled at Oct 12 2001 19:44:55
(c) 2000 Stanislav V. Mekhanoshin (rampitec@tu.spb.ru, 2:5030/172.9@fidonet)
----------------------------------------------------------------------------
Connection time : 00:02:07
Handshake Time/Retries : 57 sec/2
TX Rate (Last/Init/Min/Max) : 26400/26400/26400/26400
RX Rate (Last/Init/Min/Max) : 14400/21600/14400/21600
Modulation/Protocol/Compression : V.34/LAPM/V.42bis
TX Symbol rate : 3429
TX/RX carrier frequency, Hz : 1959/1959
Signal Level (TX/Power Drop), -dB : 15/0
RX Signal Level (Last/Min/Max), -dB : 29/29/29
Band Edge Lower/Upper, Hz : 150/3825
Round trip delay, ms : 2.583
EQM Value (Last/Min/Max/Negative) : 60/28/65/0
EQM Samples Running Sum : 01BA
EQM Last 10 Readings : 60 60 61 62 63 65 61 59 57 56
SNR Ratio (Last/Min/Max), dB : 46/43/46
TX/RX Non-linear Encoding : ON/ON
TX/RX Precoding : ON/ON
TX/RX Constellation Shaping : ON/ON
TX Trellis Encoding : 16 state
TX Pre-emphasis : 0
TX/RX state (Max TX/RX, Last TX/RX) : 87H/85H, 87H/67H
Error Correction Status : SABME:T UA:T,R XID:T,R SYNC
Dual PCM/120 Hz detection : No/No
Energy at 3750Hz/Average Energy : 2017/1242
Retrains (Issued/Granted/Fast) : 0/0/0
Renegs (Issued/Granted) : 3/0
Retrans per frame/Frames rejected : 1/30
Total number of REJ sent/received : 30/1
Last Retrain/Reneg reason : Fall-back due to high EQM
Last Retrain/Reneg requested : Local Rate Renegotiation
Minutes Since Last Retrain/Reneg : 0
Fallback to V34 reason : 32k (Flex) or 28k(V90)
Disconnect reason : LINK DISCONNECT
Remote Manufacturer/Licensee Code : Conexant/Conexant
Remote Manufacturer's Product Caps : K56Flex, V.90
Remote V.8bis caps (type) : Digital (Server)
Remote V.8bis caps (K56Flex mode) : K56Flex prototype mode not supported
Remote V.8bis caps (K56Flex version): 1.0, 1.1
Remote K56Flex RAM version supported: 71
Remote Coding used/forced by server : A-law/Yes
Remote controller version number : 8
Remote supports symbol rate (1,2,5) : 2743:ON 2800:ON 3429:ON 3429-TX:ON
Remote supports symbol rate (3,4) : 3000-L:ON 3000-H:ON 3200-L:ON 3200-H:ON
Remote power drop support : ON
Remote max symbol rate difference : 0 steps
Remote is a CME modem : No
Remote supports V.34bis : Yes
Remote frequency source : Internal
CRe/CRd/CL/MS/ACK/NAK received : Yes/No/Yes/No/Yes/No
V.8bis success/V.8bis neg started : Yes/Yes

[Technical Support]

Судя по всему, проблема - в линии. Если есть возможность попробовать модем на заведомо хорошей линии - сделайте это. Драйвера ставить не нужно, просто запустите терминальную программу (например, Hyperterminal) и дайте модему команду:

ATDT20000

и посмотрите, на какой скорости он соединится.
_________________
Inpro
Technical Support