V.34 только - хоть убей.

[Andrew5614]

Беда с моим новым IDC-5614BXL/VR(+) Конектится замечательно, связь держит отлично, но только на V.34bis. Хочу V90 !
И прошивки пробовал разные и крутил и с друзьями и пивом крутили - ничего не помогает. Помогите, пожалуйста... Линия, кстати, нормальная, все прошлые модемы и USB и SOFT ниже 42000 не коннектились.

Inpro IDC Modems Diagnostics, Version: 1.1.4.39
28.09.2006 0:56:31 - Direct Log Write Entry
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.26
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: at \a3 m4

Общая:
Time Online.................. 00:22:00
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 31200/31200/31200/31200 bps
Rx Rate (Last/Init/Min/Max).. 33600/33600/33600/33600 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 35
Tx/Power Drop/Rx Level....... 15/3/24
SNR Last/Min/Max............. 43/43/43
Highest Rx/Tx State.......... 67/67
EQM Sum...................... 001B
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 0/0
FForwards/FBacks/FEQM/Denied. 0/0/0/0
Forced FB/FB after FF/MaxREJ. 0/0/1
Last dialed number........... TXWXXX
Flex fail

Расширенная:
Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 3429
Carrier Frequency Hz, Rx/Tx.. 1959/1959
EQM Value (Last/Min/Max)..... 35/29/42
EQM Hits..................... 0
EQM Last 10 Readings......... 37 36 33 38 41 35 37 38 35 36
Last Retrain/Reneg Status.... None
Last Retrain/Reneg Reason.... None
Reason for V.34 Fallback..... Data Pump decision to Fallback in Phase 2
Last Retrain/Reneg Time...... 22 minutes ago
Handshake Time/Retries....... 17 seconds/0
Non-linear Encoding, Rx/Tx... ON/ON
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 1
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 2,6
Last Rx/Tx State............. 67/67
Energy at 3750Hz/Average .... 1023/1221
Rx Level (Last/Min/Max), -dB. 22,7/22,7/22,7
Detection of 120 Hz Tones.... Yes
Detection of Dual PCM........ Yes
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/1
Frames Errors, Rx/Tx......... 1/57 (0,0%/1,0%)
Frames Count, Rx/Tx.......... 24114/5950
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 46
Error Control Link NAKs...... 57
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 3 069 945
Characters Sent.............. 243 765
Average CPS, Rx/Tx........... 2325/184
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 67

[Technical Support]

Пропишите в строке инициализации такие команды:

S91=18 S210.5=1 S202.5=1 S17=64

и покажите, что получается в статистике.
_________________
Inpro
Technical Support

[Andrew5614]

Вставил, до User Modem Init String пока не дошло что она изменилась, но оно так и есть - видно по результату.
Неужели он считает что у меня линия отвратительная для V90?! И что самое ужасное - неужели оно так и есть?!

Inpro IDC Modems Diagnostics, Version: 1.1.4.39
28.09.2006 22:58:31 - Outbound Call By RemoteAccess
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.26
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: at \a3 m4

Time Online.................. 00:13:59
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 28800/28800/28800/28800 bps
Rx Rate (Last/Init/Min/Max).. 38667/42667/38667/42667 bps
Modulation................... V.90
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 30
Tx/Power Drop/Rx Level....... 15/3/19
SNR Last/Min/Max............. 43/43/43
Highest Rx/Tx State.......... 67/87
EQM Sum...................... 00EE
RBS Pattern.................. 00
Rate Drop.................... 0
Digital Loss................. 2000
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 4/0
FForwards/FBacks/FEQM/Denied. 0/4/1/0
Forced FB/FB after FF/MaxREJ. 2/0/7
Last dialed number........... TXWXXX
V90


Negotiation Result (Rx/Tx)... V.90 Issue 1 (asymmetric)/V.34
Symbol Rate (Rx/Tx).......... 8000/3200
Carrier Frequency Hz, Tx..... 1829
EQM Value (Last/Min/Max)..... 30/24/103
EQM Hits..................... 0
EQM Last 10 Readings......... 33 35 35 32 34 32 29 36 32 32
Fast Retrains (RRWS) Count... 1
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 11 minutes ago
Handshake Time/Retries....... 21 seconds/0
Non-linear Encoding, Rx/Tx... OFF/ON
Precoding, Rx/Tx............. OFF/ON
Shaping, Rx/Tx............... OFF/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 1
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 2,6
Last Rx/Tx State............. 67/87
Energy at 3750Hz/Average .... 1061/1
Auto Gain Amplitude, db...... 10
Rx Level (Last/Min/Max), -dB. 18,3/18,3/18,3
Detection of 120 Hz Tones.... Yes
Detection of Dual PCM........ No
V.90 RBS Pattern............. 00
V.90 Alternating RBS Pattern. 00
V.90 Digital Pad Value, db... 0,0
V.90 Optimal Speed........... 41333 bps (Reg.S120=11)
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/112
Frames Errors, Rx/Tx......... 112/0 (0,7%/0,0%)
Frames Count, Rx/Tx.......... 15540/4084
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 23
Error Control Link NAKs...... 0
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 1 893 584
Characters Sent.............. 226 213
Average CPS, Rx/Tx........... 2256/269
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 62

[Technical Support]

Чтобы IDC Diagnostics "заметил" новую строку инициализации, надо повторить процедуру "Detect modem", щёлкнув по соответствующей кнопке в программе. Тоже самое верно и для новой версии микропрограммы, IDC Diagnostics не увидит её, пока не сделаете "Detect modem".

Работать на V.90 по Вашей линии вполне можно (уже работаете)

Строку инициализации замените на такую:

S91=18 S210.7=1 S202.5=1 S55.4=1 S17=64
_________________
Inpro
Technical Support