Помогите подстроить модем

[IDC&JA]

При включенном интернет соединении статистику програмка не выдаёт. Почему? А вот протокол который выдала программа после отключения интернет соединения. Я в ней ничего не понимаю. А что скажете Вы?

Inpro IDC Modems Diagnostics, Version: 1.1.4.39
05.10.2007 23:40:18 - Direct Log Write Entry
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.26
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: <none>

Time Online.................. 00:31:19
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 31200/28800/28800/31200 bps
Rx Rate (Last/Init/Min/Max).. 45333/42667/42667/46667 bps
Modulation................... V.90
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 23
Tx/Power Drop/Rx Level....... 15/2/19
SNR Last/Min/Max............. 43/43/43
Highest Rx/Tx State.......... 67/87
EQM Sum...................... 00EA
RBS Pattern.................. 00
Rate Drop.................... 0
Digital Loss................. 2000
Retrains Issued/Granted/Auto. 0/0/1
Renegs Issued/Granted........ 6/1
FForwards/FBacks/FEQM/Denied. 3/3/3/0
Forced FB/FB after FF/MaxREJ. 0/1/5
Last dialed number........... T681681
V90 9481834246E0


Negotiation Result (Rx/Tx)... V.90 Issue 1 (asymmetric)/V.34
Symbol Rate (Rx/Tx).......... 8000/3200
Carrier Frequency Hz, Tx..... 1920
EQM Value (Last/Min/Max)..... 23/14/58
EQM Hits..................... 0
EQM Last 10 Readings......... 23 24 26 25 25 23 27 23 27 22
Fast Retrains (RRWS) Count... 2
Last Retrain/Reneg Status.... Local Fast Retrain
Last Retrain/Reneg Reason.... Local Fallforward due to Low EQM
Last Retrain/Reneg Time...... 5 minutes ago
Handshake Time/Retries....... 23 seconds/0
Non-linear Encoding, Rx/Tx... OFF/OFF
Precoding, Rx/Tx............. OFF/OFF
Shaping, Rx/Tx............... OFF/OFF
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 6
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 3,8
Last Rx/Tx State............. 65/87
Energy at 3750Hz/Average .... 1842/1085
Auto Gain Amplitude, db...... 10
Rx Level (Last/Min/Max), -dB. 18,3/18,3/18,3
Detection of 120 Hz Tones.... Yes
Detection of Dual PCM........ No
V.90 RBS Pattern............. 00
V.90 Alternating RBS Pattern. 00
V.90 Digital Pad Value, db... 0,0
V.90 Optimal Speed........... No Limit (Reg.S120=0)
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 02
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Server (Digital)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... External
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/97
Frames Errors, Rx/Tx......... 97/12 (0,3%/0,1%)
Frames Count, Rx/Tx.......... 33085/9764
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 7
Error Control Link NAKs...... 12
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 4 194 435
Characters Sent.............. 775 156
Average CPS, Rx/Tx........... 2232/412
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 62


Inpro IDC Modems Diagnostics, Version: 1.1.4.39
05.10.2007 23:40:18 - Direct Log Write Entry
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.26
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: <none>

Time Online.................. 00:31:19
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 31200/28800/28800/31200 bps
Rx Rate (Last/Init/Min/Max).. 45333/42667/42667/46667 bps
Modulation................... V.90
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 23
Tx/Power Drop/Rx Level....... 15/2/19
SNR Last/Min/Max............. 43/43/43
Highest Rx/Tx State.......... 67/87
EQM Sum...................... 00EA
RBS Pattern.................. 00
Rate Drop.................... 0
Digital Loss................. 2000
Retrains Issued/Granted/Auto. 0/0/1
Renegs Issued/Granted........ 6/1
FForwards/FBacks/FEQM/Denied. 3/3/3/0
Forced FB/FB after FF/MaxREJ. 0/1/5
Last dialed number........... T681681
V90 9481834246E0


Negotiation Result (Rx/Tx)... V.90 Issue 1 (asymmetric)/V.34
Symbol Rate (Rx/Tx).......... 8000/3200
Carrier Frequency Hz, Tx..... 1920
EQM Value (Last/Min/Max)..... 23/14/58
EQM Hits..................... 0
EQM Last 10 Readings......... 23 24 26 25 25 23 27 23 27 22
Fast Retrains (RRWS) Count... 2
Last Retrain/Reneg Status.... Local Fast Retrain
Last Retrain/Reneg Reason.... Local Fallforward due to Low EQM
Last Retrain/Reneg Time...... 5 minutes ago
Handshake Time/Retries....... 23 seconds/0
Non-linear Encoding, Rx/Tx... OFF/OFF
Precoding, Rx/Tx............. OFF/OFF
Shaping, Rx/Tx............... OFF/OFF
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 6
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 3,8
Last Rx/Tx State............. 65/87
Energy at 3750Hz/Average .... 1842/1085
Auto Gain Amplitude, db...... 10
Rx Level (Last/Min/Max), -dB. 18,3/18,3/18,3
Detection of 120 Hz Tones.... Yes
Detection of Dual PCM........ No
V.90 RBS Pattern............. 00
V.90 Alternating RBS Pattern. 00
V.90 Digital Pad Value, db... 0,0
V.90 Optimal Speed........... No Limit (Reg.S120=0)
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 02
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Server (Digital)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... External
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/97
Frames Errors, Rx/Tx......... 97/12 (0,3%/0,1%)
Frames Count, Rx/Tx.......... 33085/9764
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 7
Error Control Link NAKs...... 12
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 4 194 435
Characters Sent.............. 775 156
Average CPS, Rx/Tx........... 2232/412
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 62

[Technical Support]

Когда соединение установлено, модем "занят" другой программой (Windows Dial-Up Networking) и соответственно, IDC Diagnostics не имеет доступа к модему. Поэтому сбор статистики с помощью IDC Diagnostics возможен только после разрыва соединения.

Что касается подстройки модема, то пропишите такую строку инициализации:

S91=18 S210.7=1 S55.4=1 S17=64
_________________
Inpro
Technical Support