Предыдущая тема :: Следующая тема |
Автор |
Сообщение |
mega Associated member
Зарегистрирован: 24.02.2005 Сообщения: 11
|
Добавлено: Пн Апр 25, 2005 1:09 pm Заголовок сообщения: Помогите как то увеличить скорость IDC 5614 BXL VR+ |
|
|
Ситуация такая , есть модем IDC 5614 BXL VR+ , только что после
кап. ремонта , поэтому внутренние поломки мало вероятны. Есть
старая аналоговая АТС с плохой линией. Если в строке
инициаллизации ничего не писать , то модем вообще не может
приконектится ни к одному провайдеру. Я скача программку
EasyIDC , которая в 2-шакалах выставляет агрессивность и
чуствительность (раньше, 2 года назад я писал эти парамеры в ручную)
и вот если в этих шкалах поставить максимумы шкал этой программы
15 и агрессинвость 80 + Если написать AT+MS=11 ,
то быстрее 12000 не конектится. Если написать AT+MS=10 ,
то иногда конектится на 14400, Надо отдать должно связь при этом вроде устойчивая.
Несколько лет назад мне удавалась на этой же АТС выжимать и 28800 и
21600 и реально связь была. Обидно то , что брал у друга GVC модем старой
модели 33,6 , и он без всяких настроек конектится на 31200.
Программой IDC Diagnostic собрал несколько статистик соединений:
Inpro IDC Modems Diagnostics, Version: 1.1.4.39
23.04.2005 16:25:18 - Outbound Call By RemoteAccess
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.25
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: ATM5S210.7=1S55.3=1+MS=11,,,31200,,,21600
Time Online.................. 00:01:45
Termination Reason........... RETRAIN FAILURE
Tx Rate (Last/Init/Min/Max).. 9600/ 9600/ 9600/ 9600 bps
Rx Rate (Last/Init/Min/Max).. 12000/12000/ 9600/12000 bps
Modulation................... V.34bis
Protocol/Compression......... NONE
Line Quality................. 114
Tx/Power Drop/Rx Level....... 15/0/39
SNR Last/Min/Max............. 39/31/41
Highest Rx/Tx State.......... 64/67
EQM Sum...................... 11EF
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/2/0
Renegs Issued/Granted........ 1/0
FForwards/FBacks/Denied...... 0/1/0
Forced FB/FB after FF/MaxREJ. 0/0/0
Last dialed number........... P7204343
Flex fail
Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 3429
Carrier Frequency Hz, Rx/Tx.. 1959/1959
EQM Value (Last/Min/Max)..... 114/20/114
EQM Hits..................... 0
EQM Last 10 Readings......... 114 38 41 43 38 35 36 38 37 38
Last Retrain/Reneg Status.... Remote Retrain
Last Retrain/Reneg Reason.... Remote Retrain
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 33 seconds/2
Non-linear Encoding, Rx/Tx... OFF/OFF
Precoding, Rx/Tx............. ON/OFF
Shaping, Rx/Tx............... ON/OFF
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 7
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 5,5
Last Rx/Tx State............. 25/25
Energy at 3750Hz/Average .... 3347/1972
Rx Level (Last/Min/Max), -dB. 37,9/37,9/19,8
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. LR:T ODP:T
Frames REJected, Last/Total.. 0/0
Frames Count, Rx/Tx.......... 0/0
Error Control Frame Size..... NONE (0)
Error Control Timeouts....... 0
Error Control Link NAKs...... 0
Compression Dictionary Size.. NONE (0)
Characters Received.......... 18 671
Characters Sent.............. 3 789
Average CPS, Rx/Tx........... 177/36
Characters Lost, Rx/Tx....... 7484/0
Estimated Noise Level, -dBm.. 78
Inpro IDC Modems Diagnostics, Version: 1.1.4.39
23.04.2005 16:51:45 - Outbound Call By RemoteAccess
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.25
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: ATM5S210.7=1S55.3=1+MS=11,,,31200,,,21600
Time Online.................. 00:25:26
Termination Reason........... NO REMOTE RESPONSE
Tx Rate (Last/Init/Min/Max).. 9600/12000/ 9600/12000 bps
Rx Rate (Last/Init/Min/Max).. 9600/12000/ 9600/12000 bps
Modulation................... V.32bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 82
Tx/Power Drop/Rx Level....... 15/NA/43
SNR Last/Min/Max............. NA/NA/NA
Highest Rx/Tx State.......... 00/00
EQM Sum...................... 0000
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 1/0/0
Renegs Issued/Granted........ 2/0
FForwards/FBacks/Denied...... 0/2/0
Forced FB/FB after FF/MaxREJ. 1/1/7
Last dialed number........... P7204343
Flex fail
EQM Value (Last/Min/Max)..... 82/12/105
EQM Hits..................... 0
EQM Last 10 Readings......... 105 105 100 18 18 17 19 19 17 16
Last Retrain/Reneg Status.... Local Retrain
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 15 seconds/0
Round trip delay, ms......... 4,3
Last Rx/Tx State............. 02/05
Rx Level (Last/Min/Max), -dB. 41,5/41,5/6,3
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/124
Frames Errors, Rx/Tx......... 124/47 (0,7%/1,1%)
Frames Count, Rx/Tx.......... 16581/4114
Error Control Frame Size..... V.42 LAPM (64)
Error Control Timeouts....... 15
Error Control Link NAKs...... 47
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 1 345 303
Characters Sent.............. 181 952
Average CPS, Rx/Tx........... 881/119
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 100 |
|
Вернуться к началу |
|
|
mega Associated member
Зарегистрирован: 24.02.2005 Сообщения: 11
|
Добавлено: Пн Апр 25, 2005 1:10 pm Заголовок сообщения: |
|
|
Inpro IDC Modems Diagnostics, Version: 1.1.4.39
23.04.2005 16:52:09 - Direct Log Write Entry
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.25
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: ATM5S210.7=1S55.3=1+MS=11,,,31200,,,21600
Time Online.................. 00:25:26
Termination Reason........... NO REMOTE RESPONSE
Tx Rate (Last/Init/Min/Max).. 9600/12000/ 9600/12000 bps
Rx Rate (Last/Init/Min/Max).. 9600/12000/ 9600/12000 bps
Modulation................... V.32bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 82
Tx/Power Drop/Rx Level....... 15/NA/43
SNR Last/Min/Max............. NA/NA/NA
Highest Rx/Tx State.......... 00/00
EQM Sum...................... 0000
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 1/0/0
Renegs Issued/Granted........ 2/0
FForwards/FBacks/Denied...... 0/2/0
Forced FB/FB after FF/MaxREJ. 1/1/7
Last dialed number........... P7204343
Flex fail
EQM Value (Last/Min/Max)..... 82/12/105
EQM Hits..................... 0
EQM Last 10 Readings......... 105 105 100 18 18 17 19 19 17 16
Last Retrain/Reneg Status.... Local Retrain
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 15 seconds/0
Round trip delay, ms......... 4,3
Last Rx/Tx State............. 02/05
Rx Level (Last/Min/Max), -dB. 41,5/41,5/6,3
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/124
Frames Errors, Rx/Tx......... 124/47 (0,7%/1,1%)
Frames Count, Rx/Tx.......... 16581/4114
Error Control Frame Size..... V.42 LAPM (64)
Error Control Timeouts....... 15
Error Control Link NAKs...... 47
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 1 345 303
Characters Sent.............. 181 952
Average CPS, Rx/Tx........... 881/119
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 100
Inpro IDC Modems Diagnostics, Version: 1.1.4.39
23.04.2005 17:01:11 - Outbound Call By RemoteAccess
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.25
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: AT+MS=10
Time Online.................. 00:03:58
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 9600/ 9600/ 4800/ 9600 bps
Rx Rate (Last/Init/Min/Max).. 9600/ 9600/ 4800/ 9600 bps
Modulation................... V.32bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 19
Tx/Power Drop/Rx Level....... 15/NA/19
SNR Last/Min/Max............. NA/NA/NA
Highest Rx/Tx State.......... 00/00
EQM Sum...................... 0000
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 3/6
FForwards/FBacks/Denied...... 3/0/3
Forced FB/FB after FF/MaxREJ. 0/0/6
Last dialed number........... P7174276
Flex fail
EQM Value (Last/Min/Max)..... 19/6/79
EQM Hits..................... 0
EQM Last 10 Readings......... 28 20 21 23 18 19 22 21 20 20
Last Retrain/Reneg Status.... Remote Rate Renegotiation
Last Retrain/Reneg Reason.... Remote Rate Renegotiation
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 18 seconds/0
Round trip delay, ms......... 3,5
Last Rx/Tx State............. 02/05
Rx Level (Last/Min/Max), -dB. 18,9/19,3/18,9
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/12
Frames Errors, Rx/Tx......... 12/0 (0,9%/0,0%)
Frames Count, Rx/Tx.......... 1350/303
Error Control Frame Size..... V.42 LAPM (64)
Error Control Timeouts....... 1
Error Control Link NAKs...... 0
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 100 548
Characters Sent.............. 13 266
Average CPS, Rx/Tx........... 422/55
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 100
Inpro IDC Modems Diagnostics, Version: 1.1.4.39
23.04.2005 17:03:11 - Outbound Call By RemoteAccess
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.25
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: AT+MS=10
Time Online.................. 00:00:37
Termination Reason........... LINK DISCONNECT
Tx Rate (Last/Init/Min/Max).. 7200/12000/ 7200/12000 bps
Rx Rate (Last/Init/Min/Max).. 7200/12000/ 7200/12000 bps
Modulation................... V.32bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 22
Tx/Power Drop/Rx Level....... 15/NA/23
SNR Last/Min/Max............. NA/NA/NA
Highest Rx/Tx State.......... 00/00
EQM Sum...................... 0000
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 2/0
FForwards/FBacks/Denied...... 0/2/0
Forced FB/FB after FF/MaxREJ. 0/0/1
Last dialed number........... P7157617
Flex fail
EQM Value (Last/Min/Max)..... 22/21/99
EQM Hits..................... 0
EQM Last 10 Readings......... 27 31 21 28 25 27 24 22 29 22
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 17 seconds/0
Round trip delay, ms......... 3,5
Last Rx/Tx State............. 02/05
Rx Level (Last/Min/Max), -dB. 23,0/23,0/22,6
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:T UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/1
Frames Errors, Rx/Tx......... 1/0 (2,8%/0,0%)
Frames Count, Rx/Tx.......... 36/13
Error Control Frame Size..... V.42 LAPM (64)
Error Control Timeouts....... 8
Error Control Link NAKs...... 0
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 751
Characters Sent.............. 358
Average CPS, Rx/Tx........... 20/9
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 100
Inpro IDC Modems Diagnostics, Version: 1.1.4.39
23.04.2005 17:04:29 - Outbound Call By RemoteAccess
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.25
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: AT+MS=10
Time Online.................. 00:00:30
Termination Reason........... RETRAIN FAILURE
Tx Rate (Last/Init/Min/Max).. 14400/14400/14400/14400 bps
Rx Rate (Last/Init/Min/Max).. 14400/14400/14400/14400 bps
Modulation................... V.32bis
Protocol/Compression......... NONE
Line Quality................. 73
Tx/Power Drop/Rx Level....... 15/NA/7
SNR Last/Min/Max............. NA/NA/NA
Highest Rx/Tx State.......... 00/00
EQM Sum...................... 0000
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/1
Renegs Issued/Granted........ 1/0
FForwards/FBacks/Denied...... 0/1/0
Forced FB/FB after FF/MaxREJ. 0/0/0
Last dialed number........... P7157617
Flex fail
EQM Value (Last/Min/Max)..... 73/98/100
EQM Hits..................... 0
EQM Last 10 Readings......... 98 99 98 0 255 255 255 255 255 255
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 18 seconds/0
Round trip delay, ms......... 3,5
Last Rx/Tx State............. 02/05
Rx Level (Last/Min/Max), -dB. 6,0/34,5/6,0
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Error Correction Status Byte. ADP:R ODP:T
Frames REJected, Last/Total.. 0/0
Frames Count, Rx/Tx.......... 0/0
Error Control Frame Size..... NONE (0)
Error Control Timeouts....... 0
Error Control Link NAKs...... 0
Compression Dictionary Size.. NONE (0)
Characters Received.......... 8 301
Characters Sent.............. 426
Average CPS, Rx/Tx........... 276/14
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 100
Inpro IDC Modems Diagnostics, Version: 1.1.4.39
23.04.2005 17:08:33 - Outbound Call By RemoteAccess
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.25
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: AT+MS=10
Time Online.................. 00:01:05
Termination Reason........... LINK DISCONNECT
Tx Rate (Last/Init/Min/Max).. 4800/ 9600/ 4800/ 9600 bps
Rx Rate (Last/Init/Min/Max).. 4800/ 9600/ 4800/ 9600 bps
Modulation................... V.32bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 24
Tx/Power Drop/Rx Level....... 15/NA/26
SNR Last/Min/Max............. NA/NA/NA
Highest Rx/Tx State.......... 00/00
EQM Sum...................... 0000
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 1/0
FForwards/FBacks/Denied...... 0/1/0
Forced FB/FB after FF/MaxREJ. 1/0/7
Last dialed number........... P065
Flex fail
EQM Value (Last/Min/Max)..... 24/19/110
EQM Hits..................... 0
EQM Last 10 Readings......... 23 21 20 24 20 24 23 26 23 24
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 1 minutes ago
Handshake Time/Retries....... 39 seconds/0
Round trip delay, ms......... 1,0
Last Rx/Tx State............. 00/00
Rx Level (Last/Min/Max), -dB. 25,6/25,6/25,2
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:T UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/13
Frames Errors, Rx/Tx......... 13/0 (3,6%/0,0%)
Frames Count, Rx/Tx.......... 366/121
Error Control Frame Size..... V.42 LAPM (64)
Error Control Timeouts....... 5
Error Control Link NAKs...... 0
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 9 363
Characters Sent.............. 3 984
Average CPS, Rx/Tx........... 144/61
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 100
Inpro IDC Modems Diagnostics, Version: 1.1.4.39
23.04.2005 17:43:59 - Outbound Call By RemoteAccess
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.25
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: AT+MS=10
Time Online.................. 00:02:47
Termination Reason........... NO REMOTE RESPONSE
Tx Rate (Last/Init/Min/Max).. 9600/ 4800/ 4800/12000 bps
Rx Rate (Last/Init/Min/Max).. 9600/ 4800/ 4800/12000 bps
Modulation................... V.32bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 107
Tx/Power Drop/Rx Level....... 15/NA/35
SNR Last/Min/Max............. NA/NA/NA
Highest Rx/Tx State.......... 00/00
EQM Sum...................... 0000
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 5/0
FForwards/FBacks/Denied...... 3/2/1
Forced FB/FB after FF/MaxREJ. 1/1/7
Last dialed number........... P7204343
Flex fail
EQM Value (Last/Min/Max)..... 107/5/109
EQM Hits..................... 0
EQM Last 10 Readings......... 109 109 105 106 101 21 19 16 21 18
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 15 seconds/0
Round trip delay, ms......... 3,9
Last Rx/Tx State............. 02/05
Rx Level (Last/Min/Max), -dB. 35,2/35,2/6,3
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 0/23
Frames Errors, Rx/Tx......... 23/0 (1,1%/0,0%)
Frames Count, Rx/Tx.......... 2076/458
Error Control Frame Size..... V.42 LAPM (64)
Error Control Timeouts....... 6
Error Control Link NAKs...... 0
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 158 728
Characters Sent.............. 26 026
Average CPS, Rx/Tx........... 950/155
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 100
Inpro IDC Modems Diagnostics, Version: 1.1.4.39
23.04.2005 20:51:54 - Outbound Call By RemoteAccess
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.25
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: at+ms=10
Time Online.................. 00:05:14
Termination Reason........... RETRAIN FAILURE
Tx Rate (Last/Init/Min/Max).. 9600/12000/ 9600/12000 bps
Rx Rate (Last/Init/Min/Max).. 9600/12000/ 9600/12000 bps
Modulation................... V.32bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 127
Tx/Power Drop/Rx Level....... 15/NA/31
SNR Last/Min/Max............. NA/NA/NA
Highest Rx/Tx State.......... 00/00
EQM Sum...................... 0000
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 1/0/0
Renegs Issued/Granted........ 8/0
FForwards/FBacks/Denied...... 4/4/1
Forced FB/FB after FF/MaxREJ. 2/3/8
Last dialed number........... P7029029
Flex fail
EQM Value (Last/Min/Max)..... 127/4/127
EQM Hits..................... 0
EQM Last 10 Readings......... 127 127 127 127 127 127 17 20 4 53
Last Retrain/Reneg Status.... Local Retrain
Last Retrain/Reneg Reason.... Lost Connection
Last Retrain/Reneg Time...... 1 minutes ago
Handshake Time/Retries....... 14 seconds/0
Round trip delay, ms......... 4,3
Last Rx/Tx State............. 02/05
Rx Level (Last/Min/Max), -dB. 30,8/30,8/6,0
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 8/42
Frames Errors, Rx/Tx......... 42/1 (1,4%/0,1%)
Frames Count, Rx/Tx.......... 3036/824
Error Control Frame Size..... V.42 LAPM (64)
Error Control Timeouts....... 0
Error Control Link NAKs...... 1
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 164 677
Characters Sent.............. 34 415
Average CPS, Rx/Tx........... 524/109
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 100 |
|
Вернуться к началу |
|
|
mega Associated member
Зарегистрирован: 24.02.2005 Сообщения: 11
|
Добавлено: Пн Апр 25, 2005 1:11 pm Заголовок сообщения: |
|
|
Inpro IDC Modems Diagnostics, Version: 1.1.4.39
23.04.2005 21:08:55 - Outbound Call By RemoteAccess
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.25
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: at+ms=10
Time Online.................. 00:15:52
Termination Reason........... RETRAIN FAILURE
Tx Rate (Last/Init/Min/Max).. 9600/12000/ 9600/12000 bps
Rx Rate (Last/Init/Min/Max).. 9600/12000/ 9600/12000 bps
Modulation................... V.32bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 108
Tx/Power Drop/Rx Level....... 15/NA/7
SNR Last/Min/Max............. NA/NA/NA
Highest Rx/Tx State.......... 00/00
EQM Sum...................... 0000
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/1
Renegs Issued/Granted........ 9/0
FForwards/FBacks/Denied...... 4/5/1
Forced FB/FB after FF/MaxREJ. 4/2/11
Last dialed number........... P7204343
Flex fail
EQM Value (Last/Min/Max)..... 108/15/110
EQM Hits..................... 0
EQM Last 10 Readings......... 110 110 107 107 106 106 24 43 23 25
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 15 seconds/0
Round trip delay, ms......... 3,5
Last Rx/Tx State............. 02/05
Rx Level (Last/Min/Max), -dB. 6,0/20,4/6,0
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 4/155
Frames Errors, Rx/Tx......... 155/3 (1,1%/0,2%)
Frames Count, Rx/Tx.......... 14557/1651
Error Control Frame Size..... V.42 LAPM (64)
Error Control Timeouts....... 6
Error Control Link NAKs...... 3
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 797 210
Characters Sent.............. 56 635
Average CPS, Rx/Tx........... 837/59
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 100
Inpro IDC Modems Diagnostics, Version: 1.1.4.39
23.04.2005 21:41:33 - Outbound Call By RemoteAccess
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.25
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: at+ms=10
Time Online.................. 00:31:40
Termination Reason........... KEY ABORT
Tx Rate (Last/Init/Min/Max).. 9600/ 9600/ 9600/ 9600 bps
Rx Rate (Last/Init/Min/Max).. 9600/ 9600/ 9600/ 9600 bps
Modulation................... V.32bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 113
Tx/Power Drop/Rx Level....... 15/NA/26
SNR Last/Min/Max............. NA/NA/NA
Highest Rx/Tx State.......... 00/00
EQM Sum...................... 0000
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 2/0
FForwards/FBacks/Denied...... 2/0/2
Forced FB/FB after FF/MaxREJ. 0/0/6
Last dialed number........... P7029029
Flex fail
EQM Value (Last/Min/Max)..... 113/16/113
EQM Hits..................... 0
EQM Last 10 Readings......... 113 106 106 22 20 21 24 23 22 20
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallforward due to Low EQM
Last Retrain/Reneg Time...... 29 minutes ago
Handshake Time/Retries....... 15 seconds/0
Round trip delay, ms......... 4,3
Last Rx/Tx State............. 02/05
Rx Level (Last/Min/Max), -dB. 25,2/25,2/6,3
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/240
Frames Errors, Rx/Tx......... 240/18 (0,8%/0,3%)
Frames Count, Rx/Tx.......... 29929/7075
Error Control Frame Size..... V.42 LAPM (64)
Error Control Timeouts....... 10
Error Control Link NAKs...... 18
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 1 959 661
Characters Sent.............. 269 617
Average CPS, Rx/Tx........... 1031/141
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 100
Inpro IDC Modems Diagnostics, Version: 1.1.4.39
23.04.2005 22:22:28 - Outbound Call By RemoteAccess
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.25
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: at+ms=10
Time Online.................. 00:33:19
Termination Reason........... KEY ABORT
Tx Rate (Last/Init/Min/Max).. 9600/ 9600/ 7200/ 9600 bps
Rx Rate (Last/Init/Min/Max).. 9600/ 9600/ 7200/ 9600 bps
Modulation................... V.32bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 23
Tx/Power Drop/Rx Level....... 15/NA/19
SNR Last/Min/Max............. NA/NA/NA
Highest Rx/Tx State.......... 00/00
EQM Sum...................... 0000
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/1
Renegs Issued/Granted........ 10/2
FForwards/FBacks/Denied...... 7/3/4
Forced FB/FB after FF/MaxREJ. 2/1/8
Last dialed number........... P7029029
Flex fail
EQM Value (Last/Min/Max)..... 23/0/59
EQM Hits..................... 0
EQM Last 10 Readings......... 22 20 17 18 20 21 22 22 19 23
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallforward due to Low EQM
Last Retrain/Reneg Time...... 11 minutes ago
Handshake Time/Retries....... 16 seconds/0
Round trip delay, ms......... 4,3
Last Rx/Tx State............. 02/05
Rx Level (Last/Min/Max), -dB. 18,6/18,6/14,1
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 0/104
Frames Errors, Rx/Tx......... 360/41 (1,1%/0,6%)
Frames Count, Rx/Tx.......... 31899/6752
Error Control Frame Size..... V.42 LAPM (64)
Error Control Timeouts....... 10
Error Control Link NAKs...... 41
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 2 049 617
Characters Sent.............. 221 357
Average CPS, Rx/Tx........... 1025/110
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 100
Inpro IDC Modems Diagnostics, Version: 1.1.4.39
23.04.2005 22:27:21 - Outbound Call By RemoteAccess
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.25
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: at+ms=10
Time Online.................. 00:03:08
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 9600/ 7200/ 7200/ 9600 bps
Rx Rate (Last/Init/Min/Max).. 9600/ 7200/ 7200/ 9600 bps
Modulation................... V.32bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 21
Tx/Power Drop/Rx Level....... 15/NA/19
SNR Last/Min/Max............. NA/NA/NA
Highest Rx/Tx State.......... 00/00
EQM Sum...................... 0000
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 3/0
FForwards/FBacks/Denied...... 3/0/2
Forced FB/FB after FF/MaxREJ. 0/0/3
Last dialed number........... P7029029
Flex fail
EQM Value (Last/Min/Max)..... 21/10/38
EQM Hits..................... 0
EQM Last 10 Readings......... 25 20 20 19 22 20 19 19 23 21
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallforward due to Low EQM
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 29 seconds/0
Round trip delay, ms......... 4,3
Last Rx/Tx State............. 02/05
Rx Level (Last/Min/Max), -dB. 18,6/18,9/18,6
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/10
Frames Errors, Rx/Tx......... 10/2 (0,5%/0,4%)
Frames Count, Rx/Tx.......... 1909/491
Error Control Frame Size..... V.42 LAPM (64)
Error Control Timeouts....... 1
Error Control Link NAKs...... 2
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 179 962
Characters Sent.............. 20 013
Average CPS, Rx/Tx........... 957/106
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 100
Inpro IDC Modems Diagnostics, Version: 1.1.4.39
23.04.2005 22:29:51 - Direct Log Write Entry
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.25
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: at+ms=10
Time Online.................. 00:03:08
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 9600/ 7200/ 7200/ 9600 bps
Rx Rate (Last/Init/Min/Max).. 9600/ 7200/ 7200/ 9600 bps
Modulation................... V.32bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 21
Tx/Power Drop/Rx Level....... 15/NA/19
SNR Last/Min/Max............. NA/NA/NA
Highest Rx/Tx State.......... 00/00
EQM Sum...................... 0000
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 3/0
FForwards/FBacks/Denied...... 3/0/2
Forced FB/FB after FF/MaxREJ. 0/0/3
Last dialed number........... P7029029
Flex fail
EQM Value (Last/Min/Max)..... 21/10/38
EQM Hits..................... 0
EQM Last 10 Readings......... 25 20 20 19 22 20 19 19 23 21
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallforward due to Low EQM
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 29 seconds/0
Round trip delay, ms......... 4,3
Last Rx/Tx State............. 02/05
Rx Level (Last/Min/Max), -dB. 18,6/18,9/18,6
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/10
Frames Errors, Rx/Tx......... 10/2 (0,5%/0,4%)
Frames Count, Rx/Tx.......... 1909/491
Error Control Frame Size..... V.42 LAPM (64)
Error Control Timeouts....... 1
Error Control Link NAKs...... 2
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 179 962
Characters Sent.............. 20 013
Average CPS, Rx/Tx........... 957/106
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 100
Inpro IDC Modems Diagnostics, Version: 1.1.4.39
23.04.2005 22:30:05 - Direct Log Write Entry
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.25
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: at+ms=10
Time Online.................. 00:03:08
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 9600/ 7200/ 7200/ 9600 bps
Rx Rate (Last/Init/Min/Max).. 9600/ 7200/ 7200/ 9600 bps
Modulation................... V.32bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 21
Tx/Power Drop/Rx Level....... 15/NA/19
SNR Last/Min/Max............. NA/NA/NA
Highest Rx/Tx State.......... 00/00
EQM Sum...................... 0000
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 3/0
FForwards/FBacks/Denied...... 3/0/2
Forced FB/FB after FF/MaxREJ. 0/0/3
Last dialed number........... P7029029
Flex fail
EQM Value (Last/Min/Max)..... 21/10/38
EQM Hits..................... 0
EQM Last 10 Readings......... 25 20 20 19 22 20 19 19 23 21
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallforward due to Low EQM
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 29 seconds/0
Round trip delay, ms......... 4,3
Last Rx/Tx State............. 02/05
Rx Level (Last/Min/Max), -dB. 18,6/18,9/18,6
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/10
Frames Errors, Rx/Tx......... 10/2 (0,5%/0,4%)
Frames Count, Rx/Tx.......... 1909/491
Error Control Frame Size..... V.42 LAPM (64)
Error Control Timeouts....... 1
Error Control Link NAKs...... 2
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 179 962
Characters Sent.............. 20 013
Average CPS, Rx/Tx........... 957/106
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 100
Inpro IDC Modems Diagnostics, Version: 1.1.4.39
23.04.2005 23:26:39 - Direct Log Write Entry
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.25
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: at+MS=11,,,31200,,,21600
Time Online.................. 00:15:56
Termination Reason........... NO REMOTE RESPONSE
Tx Rate (Last/Init/Min/Max).. 9600/12000/ 9600/12000 bps
Rx Rate (Last/Init/Min/Max).. 9600/12000/ 9600/12000 bps
Modulation................... V.32bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 106
Tx/Power Drop/Rx Level....... 15/NA/20
SNR Last/Min/Max............. NA/NA/NA
Highest Rx/Tx State.......... 00/00
EQM Sum...................... 0000
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 8/0
FForwards/FBacks/Denied...... 3/5/0
Forced FB/FB after FF/MaxREJ. 4/3/10
Last dialed number........... P7029029
Flex fail
EQM Value (Last/Min/Max)..... 106/16/107
EQM Hits..................... 0
EQM Last 10 Readings......... 105 105 107 107 21 19 19 19 20 20
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 14 seconds/0
Round trip delay, ms......... 4,3
Last Rx/Tx State............. 02/05
Rx Level (Last/Min/Max), -dB. 20,0/20,0/6,0
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/132
Frames Errors, Rx/Tx......... 132/6 (0,8%/0,2%)
Frames Count, Rx/Tx.......... 16386/3582
Error Control Frame Size..... V.42 LAPM (64)
Error Control Timeouts....... 3
Error Control Link NAKs...... 6
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 2 074 499
Characters Sent.............. 45 377
Average CPS, Rx/Tx........... 2169/47
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 100 |
|
Вернуться к началу |
|
|
Technical Support Expert
Зарегистрирован: 31.10.2002 Сообщения: 6330
|
Добавлено: Пн Апр 25, 2005 1:57 pm Заголовок сообщения: |
|
|
Зря Вы вписали так много статистик в форум. На будущее: архивируйте длинные файлы статистики ZIP или RAR и высылайте нам на e-mail: support@inpro.us.com. Длинные сообщения делают тему малопригодной для чтения; 1-2 характЕрных статистики, вписанные в тему и выделенные с помощью "Code", смотрятся нормально, но когда их десяток...
К теме: если другой модем хорошо работает на Вашей линии, то разумнее всего подозревать неисправность Вашего модема. Лучше всего его проверить на какой-нибудь заведомо хорошей линии (чтобы исключить совпадения, вдруг смена модема совпала с внезапным "просветлением" на Вашей АТС). _________________ Inpro
Technical Support |
|
Вернуться к началу |
|
|
mega Associated member
Зарегистрирован: 24.02.2005 Сообщения: 11
|
Добавлено: Пн Апр 25, 2005 3:31 pm Заголовок сообщения: |
|
|
тот 2-й модем , работал хорошо , тогда же 2 года назад .
Счас нет возможности взять его. Интересует вопрос ,
что делать именно счас. Вараиант неисправности можно откинуть , т.к.
только что его починили в диллерской мастреской , и полностью,
практически заменили все внутренности , т.к. они сгорели.
Проверял модем на другой линни правда , то же такой же плохой ,
и получается та же ситуация 12000 и 14400 , правда через
терминал конектился на этой другой линии и на 16800 и 21600,
правда реально этой скорости не было.
Отсюда тот же вопрос , как подымать скорость в случае на моей линии ?
поповоду много статистики , которую я написал: видите ли , моя плохая линия менят уровень
качества постоянно , и я думал это вам поможет , для того ,что бы вы
мне подсказали несколько строк инициализации , в зависмотсти от качества линии
на данный момент. |
|
Вернуться к началу |
|
|
Technical Support Expert
Зарегистрирован: 31.10.2002 Сообщения: 6330
|
Добавлено: Вт Апр 26, 2005 3:30 pm Заголовок сообщения: |
|
|
Сравнивать модемы можно лишь в одинаковых условиях. Состояние телефонной связи может меняться ежеминутно. Вспоминать о том, что было 2 года назад, совершенно бессмысленно.
Проблема "сейчас" состоит, по-видимому, в большом затухании сигнала. Попробуйте такую строку инициализации:
S91=9 S210=136 +MS=11,,,,,,7200
Покажите, что получается в статистике. _________________ Inpro
Technical Support |
|
Вернуться к началу |
|
|
mega Associated member
Зарегистрирован: 24.02.2005 Сообщения: 11
|
Добавлено: Вт Апр 26, 2005 11:33 pm Заголовок сообщения: |
|
|
с такой строкой инциаллизации не получилось законектится вообще.
Странный звуки из динамика и модем не разу не смог установить
соединение , поэтому статисику собрать тоже не получилось. |
|
Вернуться к началу |
|
|
Technical Support Expert
Зарегистрирован: 31.10.2002 Сообщения: 6330
|
Добавлено: Вт Апр 26, 2005 11:35 pm Заголовок сообщения: |
|
|
Попробуйте заменить S91=9 на S91=15.
Получилось? _________________ Inpro
Technical Support |
|
Вернуться к началу |
|
|
mega Associated member
Зарегистрирован: 24.02.2005 Сообщения: 11
|
Добавлено: Ср Апр 27, 2005 9:46 pm Заголовок сообщения: |
|
|
Скорость упала до 4,8 , привожу статистику :
Inpro IDC Modems Diagnostics, Version: 1.1.4.39
27.04.2005 21:35:23 - Outbound Call By RemoteAccess
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.25
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: ATS91=15 S210=136 +MS=11,,,,,,7200
Time Online.................. 00:00:33
Termination Reason........... NO REMOTE RESPONSE
Tx Rate (Last/Init/Min/Max).. 7200/ 7200/ 7200/ 7200 bps
Rx Rate (Last/Init/Min/Max).. 7200/ 4800/ 4800/ 7200 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 126
Tx/Power Drop/Rx Level....... 15/0/15
SNR Last/Min/Max............. 36/36/36
Highest Rx/Tx State.......... 67/87
EQM Sum...................... 0000
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 2/0
FForwards/FBacks/Denied...... 1/1/0
Forced FB/FB after FF/MaxREJ. 0/0/2
Last dialed number........... P7029029
Flex fail
Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 2400
Carrier Frequency Hz, Rx/Tx.. 1600/1800
EQM Value (Last/Min/Max)..... 126/14/127
EQM Hits..................... 0
EQM Last 10 Readings......... 126 126 127 127 127 127 31 39 30 32
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 14 seconds/0
Non-linear Encoding, Rx/Tx... OFF/OFF
Precoding, Rx/Tx............. OFF/OFF
Shaping, Rx/Tx............... ON/OFF
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 0
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 7,3
Last Rx/Tx State............. 67/84
Energy at 3750Hz/Average .... 3352/1979
Rx Level (Last/Min/Max), -dB. 15,0/26,4/5,0
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. No/No/No/No/No/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 0/3
Frames Errors, Rx/Tx......... 3/0 (1,8%/0,0%)
Frames Count, Rx/Tx.......... 170/87
Error Control Frame Size..... V.42 LAPM (64)
Error Control Timeouts....... 2
Error Control Link NAKs...... 0
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 7 706
Characters Sent.............. 3 853
Average CPS, Rx/Tx........... 233/116
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 51 |
|
Вернуться к началу |
|
|
Technical Support Expert
Зарегистрирован: 31.10.2002 Сообщения: 6330
|
Добавлено: Чт Апр 28, 2005 9:18 am Заголовок сообщения: |
|
|
Что порадовало, теперь соединение установилось с первой попытки. Вам нужно постараться подобрать S91 наилучшим образом. Диапазон - от 12 до 21.
Учитывая, что параметры линии сильно изменяются от раза к разу, предстоят длительные эксперименты. Скорее всего, Вы придёте к S91=18.
Что касается того, на каком протоколе работать, на V.34 представляется более предпочтительным, прежде всего потому, что он допускает асимметрию скоростей приёма и передачи. _________________ Inpro
Technical Support |
|
Вернуться к началу |
|
|
|
|
Вы не можете начинать темы Вы не можете отвечать на сообщения Вы не можете редактировать свои сообщения Вы не можете удалять свои сообщения Вы не можете голосовать в опросах
|
Powered by phpBB © 2001, 2005 phpBB Group
|