Помогите настроить модем

[Mistik]

Здравствуйте!Помогите настроить модем IDC-5614BXL/VR+ (Plus).Заранее спасибо!
Time Online.................. 00:06:41
Termination Reason........... RETRAIN FAILURE
Tx Rate (Last/Init/Min/Max).. 33600/28800/26400/33600 bps
Rx Rate (Last/Init/Min/Max).. 31200/41333/31200/42667 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 127
Tx/Power Drop/Rx Level....... 15/2/NA
SNR Last/Min/Max............. 43/41/43
Highest Rx/Tx State.......... 21/21
EQM Sum...................... 003A
RBS Pattern.................. 00
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/4/9
Renegs Issued/Granted........ 10/0
FForwards/FBacks/FEQM/Denied. 1/9/8/0
Forced FB/FB after FF/MaxREJ. 0/1/1
Last dialed number........... P31906
Flex fail 9481C1A1


Negotiation Result (Rx/Tx)... V.90 Issue 1 (asymmetric)/V.34
Symbol Rate (Rx/Tx).......... 8000/3429
Carrier Frequency Hz, Tx..... 1959
EQM Value (Last/Min/Max)..... 127/6/127
EQM Hits..................... 0
EQM Last 10 Readings......... 127 127 127 127 127 127 10 12 10 10
Fast Retrains (RRWS) Count... 1
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Reason for V.34 Fallback..... Data Pump decision to Fallback
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 49 seconds/1
Non-linear Encoding, Rx/Tx... ON/ON
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 2
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 204,1
Last Rx/Tx State............. 20/21
Energy at 3750Hz/Average .... 4398/1920
Auto Gain Amplitude, db...... 10
Rx Level (Last/Min/Max), -dB. NA/18,3/5,0d
Detection of 120 Hz Tones.... Yes
Detection of Dual PCM........ No
V.90 RBS Pattern............. 00
V.90 Alternating RBS Pattern. 00
V.90 Digital Pad Value, db... 0,0
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/No/No/No/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex
Remote K56flex Version....... 01
Remote K56flex Capabilities.. Prototype mode supported
Remote Type.................. Client (Analog)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Unknown
Workaround Used.............. V90 Phase 2 Escape
Workaround Used.............. V34 Codex WA/V34 Stuck Phase2
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 6/3
Frames Errors, Rx/Tx......... 3/4 (0,3%/0,6%)
Frames Count, Rx/Tx.......... 923/667
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 34
Error Control Link NAKs...... 4
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 117 713
Characters Sent.............. 21 087
Average CPS, Rx/Tx........... 293/52
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 95

[Technical Support]

Попробуйте такую строку инициализации:

S91=15 S210.7=1 +MS=11,,,,,,24000

Покажите, что получается в статистике.
_________________
Inpro
Technical Support

[Mistik]

Стало работать лучше.
Time Online.................. 00:17:13
Termination Reason........... NO REMOTE RESPONSE
Tx Rate (Last/Init/Min/Max).. 24000/24000/14400/24000 bps
Rx Rate (Last/Init/Min/Max).. 33600/33600/28800/33600 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 126
Tx/Power Drop/Rx Level....... 15/0/6
SNR Last/Min/Max............. 43/22/43
Highest Rx/Tx State.......... 67/84
EQM Sum...................... 001B
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/29/6
Renegs Issued/Granted........ 8/0
FForwards/FBacks/FEQM/Denied. 5/3/0/0
Forced FB/FB after FF/MaxREJ. 1/1/7
Last dialed number........... P31906
Flex fail


Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 3429
Carrier Frequency Hz, Rx/Tx.. 1959/1959
EQM Value (Last/Min/Max)..... 126/20/127
EQM Hits..................... 0
EQM Last 10 Readings......... 126 126 126 126 127 127 36 35 31 34
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 24 seconds/0
Non-linear Encoding, Rx/Tx... ON/ON
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 1
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 203,2
Last Rx/Tx State............. 67/84
Energy at 3750Hz/Average .... 4428/1937
Rx Level (Last/Min/Max), -dB. 5,3/33,5/5,3
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 0/20
Frames Errors, Rx/Tx......... 20/12 (0,4%/0,4%)
Frames Count, Rx/Tx.......... 5233/2690
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 59
Error Control Link NAKs...... 12
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 1 028 644
Characters Sent.............. 105 260
Average CPS, Rx/Tx........... 995/101
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 49
А нельзя ли как то улучшить?

[Technical Support]