Скорость соединения

[PaulU]

у меня тройкая коробочка в которой 2 розетки сетевые, а одна телефонная? это считается в непосредственной близости? если компьютер заземлить то помех не будет даже если так близко расположены?

[Technical Support]

Всё это нужно проверять экспериментально, и только так! Из опыта, все проблемы исчезают после заземления компьютера.
_________________
Inpro
Technical Support

[PaulU]

всетаки отрывание "земли" помогло немного, при отключенном телефонном аппарате скорость обычно 38.6 а с включенным 37.2.
Заземлением я займусь.

А пока могли бы вы пока предложить какие-то настройки? Хоть чуть-ть поправить ситуацию сейчас????

[Technical Support]

Для начала попробуйте такую строчку:

S91=15 S210.7=1 S55.4=1

и покажите результат (т.е. статистику). Но по-хорошему, настраивать модем сейчас - артель "Напрасный труд". После того, как заземлите компьютер, картина полностью изменится, и придётся всё начинать сначала.
_________________
Inpro
Technical Support

[PaulU]

Inpro IDC Modems Diagnostics, Version 1.0.2.33
23.01.2004 14:27:31 - Direct Log Write Entry
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.24

Time Online.................. 00:03:44
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 28800/28800/28800/28800 bps
Rx Rate (Last/Init/Min/Max).. 37333/37333/37333/37333 bps
Modulation................... V.90
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 32
Tx/Power Drop/Rx Level....... 15/0/21
SNR Last/Min/Max............. 43/43/43
Highest Rx/Tx State.......... 67/67
EQM Sum...................... 011B
RBS Pattern.................. 00
Rate Drop.................... 0
Digital Loss................. 2000
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 0/0
FForwards/FBacks/Denied...... 0/0/0
Forced FB/FB after FF/MaxREJ. 0/0/1
Last dialed number........... T7311111
V90 9481834347E5


Negotiation Result (Rx/Tx)... V.90 Issue 1 (asymmetric)/V.34
Symbol Rate (Rx/Tx).......... 8000/3200
Carrier Frequency Hz, Tx..... 1829
EQM Value (Last/Min/Max)..... 32/27/37
EQM Hits..................... 0
EQM Last 10 Readings......... 30 34 31 31 32 34 35 35 34 34
Last Retrain/Reneg Status.... None
Last Retrain/Reneg Reason.... None
Last Retrain/Reneg Time...... 3 minutes ago
Handshake Time/Retries....... 23 seconds/0
Non-linear Encoding, Rx/Tx... OFF/ON
Precoding, Rx/Tx............. OFF/ON
Shaping, Rx/Tx............... OFF/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 2
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 3,8
Last Rx/Tx State............. 67/67
Energy at 3750Hz/Average .... 3929/2131
Auto Gain Amplitude, db...... 10
AGC Gain (Last/Min/Max)...... 85/85/85
Detection of 120 Hz Tones.... Yes
Detection of Dual PCM........ No
V.90 RBS Pattern............. 00
V.90 Alternating RBS Pattern. 00
V.90 Digital Pad Value, db... 0,0
V.90 Optimal Speed........... No Limit (Reg.S120=0)
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 03
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Server (Digital)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/1
Frames Errors, Rx/Tx......... 1/0 (0,0%/0,0%)
Frames Count, Rx/Tx.......... 3530/2113
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 1
Error Control Link NAKs...... 0
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 491 946
Characters Sent.............. 210 378
Average CPS, Rx/Tx........... 2196/939
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 64


Inpro IDC Modems Diagnostics, Version 1.0.2.33
23.01.2004 14:30:09 - Outbound Call by RemoteAccess
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.24

Time Online.................. 00:02:04
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 28800/28800/28800/28800 bps
Rx Rate (Last/Init/Min/Max).. 37333/37333/37333/37333 bps
Modulation................... V.90
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 33
Tx/Power Drop/Rx Level....... 15/0/21
SNR Last/Min/Max............. 41/41/41
Highest Rx/Tx State.......... 67/67
EQM Sum...................... 0123
RBS Pattern.................. 00
Rate Drop.................... 0
Digital Loss................. 2000
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 0/0
FForwards/FBacks/Denied...... 0/0/0
Forced FB/FB after FF/MaxREJ. 0/0/0
Last dialed number........... T7311111
V90 9481834347E5


Negotiation Result (Rx/Tx)... V.90 Issue 1 (asymmetric)/V.34
Symbol Rate (Rx/Tx).......... 8000/3200
Carrier Frequency Hz, Tx..... 1829
EQM Value (Last/Min/Max)..... 33/29/41
EQM Hits..................... 0
EQM Last 10 Readings......... 33 33 37 35 37 31 35 34 34 34
Last Retrain/Reneg Status.... None
Last Retrain/Reneg Reason.... None
Last Retrain/Reneg Time...... 2 minutes ago
Handshake Time/Retries....... 23 seconds/0
Non-linear Encoding, Rx/Tx... OFF/ON
Precoding, Rx/Tx............. OFF/ON
Shaping, Rx/Tx............... OFF/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 1
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 3,5
Last Rx/Tx State............. 67/67
Energy at 3750Hz/Average .... 3868/2114
Auto Gain Amplitude, db...... 10
AGC Gain (Last/Min/Max)...... 85/85/85
Detection of 120 Hz Tones.... Yes
Detection of Dual PCM........ No
V.90 RBS Pattern............. 00
V.90 Alternating RBS Pattern. 00
V.90 Digital Pad Value, db... 0,0
V.90 Optimal Speed........... No Limit (Reg.S120=0)
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 03
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Server (Digital)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/0
Frames Errors, Rx/Tx......... 0/0 (0,0%/0,0%)
Frames Count, Rx/Tx.......... 24/202
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 1
Error Control Link NAKs...... 0
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 561
Characters Sent.............. 7 554
Average CPS, Rx/Tx........... 4/60
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 62

[Technical Support]

Пожалуй, можно попробовать ещё чуть-чуть повысить скорость. Попробуйте добавить в строку инициализации команды:

S17=60 S120=9
_________________
Inpro
Technical Support

[PaulU]

Inpro IDC Modems Diagnostics, Version 1.0.2.33
23.01.2004 15:24:04 - Outbound Call by RemoteAccess
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.24

Time Online.................. 00:02:23
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 28800/28800/28800/28800 bps
Rx Rate (Last/Init/Min/Max).. 38667/38667/38667/38667 bps
Modulation................... V.90
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 46
Tx/Power Drop/Rx Level....... 15/0/21
SNR Last/Min/Max............. 43/43/43
Highest Rx/Tx State.......... 67/67
EQM Sum...................... 00F4
RBS Pattern.................. 00
Rate Drop.................... 0
Digital Loss................. 2000
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 0/0
FForwards/FBacks/Denied...... 0/0/0
Forced FB/FB after FF/MaxREJ. 0/0/4
Last dialed number........... T7311111
V90 9481834347E5


Negotiation Result (Rx/Tx)... V.90 Issue 1 (asymmetric)/V.34
Symbol Rate (Rx/Tx).......... 8000/3200
Carrier Frequency Hz, Tx..... 1829
EQM Value (Last/Min/Max)..... 46/37/98
EQM Hits..................... 0
EQM Last 10 Readings......... 47 42 42 41 41 41 46 42 50 46
Last Retrain/Reneg Status.... None
Last Retrain/Reneg Reason.... None
Last Retrain/Reneg Time...... 2 minutes ago
Handshake Time/Retries....... 23 seconds/0
Non-linear Encoding, Rx/Tx... OFF/ON
Precoding, Rx/Tx............. OFF/ON
Shaping, Rx/Tx............... OFF/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 4
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 3,5
Last Rx/Tx State............. 67/67
Energy at 3750Hz/Average .... 3920/2129
Auto Gain Amplitude, db...... 10
AGC Gain (Last/Min/Max)...... 85/85/85
Detection of 120 Hz Tones.... Yes
Detection of Dual PCM........ No
V.90 RBS Pattern............. 00
V.90 Alternating RBS Pattern. 00
V.90 Digital Pad Value, db... 0,0
V.90 Optimal Speed........... 38667 bps (Reg.S120=9)
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 03
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Server (Digital)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/8
Frames Errors, Rx/Tx......... 8/0 (0,9%/0,0%)
Frames Count, Rx/Tx.......... 884/630
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 4
Error Control Link NAKs...... 0
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 87 997
Characters Sent.............. 31 348
Average CPS, Rx/Tx........... 615/219
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 64

[Technical Support]

Всё, так и оставьте до окончания "разборок с заземлением".
_________________
Inpro
Technical Support

[Sergo]

Извиняюсь за вмешательство в беседу, но похоже у меня такая же проблема. Землю в проводе убрал, паралельных телефонов нет, конденсаторов в розетках тоже нет. Конденсаторы С2, С3 удалил.
Но от "120 Hz Tones.... Yes" так и не избавился :(

Судя по вашим объяснениям осталось только заземлить компьютер.
Пожалуйста объясните каким образом это сделать.
Достаточно ли просто корпус кинуть на радиатор отопления ?
В розетках земли нет.

[Technical Support]

[PaulU]

на кухне у меня есть заземленная розетка, так что туда снес компьютер. выкладываю статистику, но от помех так и не избавился.
Что делать? Системный блок подключен через упс BackUps300(это не важно?)

Inpro IDC Modems Diagnostics, Version 1.0.2.33
23.01.2004 17:34:04 - Direct Log Write Entry
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.24

Time Online.................. 00:04:53
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 28800/28800/28800/28800 bps
Rx Rate (Last/Init/Min/Max).. 38667/38667/38667/38667 bps
Modulation................... V.90
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 34
Tx/Power Drop/Rx Level....... 15/0/21
SNR Last/Min/Max............. 43/43/43
Highest Rx/Tx State.......... 67/67
EQM Sum...................... 00E9
RBS Pattern.................. 00
Rate Drop.................... 0
Digital Loss................. 2000
Retrains Issued/Granted/Auto. 0/2/0
Renegs Issued/Granted........ 0/0
FForwards/FBacks/Denied...... 0/0/0
Forced FB/FB after FF/MaxREJ. 0/0/0
Last dialed number........... T7311111
V90 9481834347E5


Negotiation Result (Rx/Tx)... V.90 Issue 1 (asymmetric)/V.34
Symbol Rate (Rx/Tx).......... 8000/3200
Carrier Frequency Hz, Tx..... 1829
EQM Value (Last/Min/Max)..... 34/28/42
EQM Hits..................... 0
EQM Last 10 Readings......... 36 37 34 32 30 32 32 32 38 34
Last Retrain/Reneg Status.... Remote Retrain
Last Retrain/Reneg Reason.... Remote Retrain
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 23 seconds/0
Non-linear Encoding, Rx/Tx... OFF/ON
Precoding, Rx/Tx............. OFF/ON
Shaping, Rx/Tx............... OFF/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 2
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 3,2
Last Rx/Tx State............. 67/67
Energy at 3750Hz/Average .... 3782/2069
Auto Gain Amplitude, db...... 10
AGC Gain (Last/Min/Max)...... 85/85/85
Detection of 120 Hz Tones.... Yes
Detection of Dual PCM........ No
V.90 RBS Pattern............. 00
V.90 Alternating RBS Pattern. 00
V.90 Digital Pad Value, db... 0,0
V.90 Optimal Speed........... 38667 bps (Reg.S120=9)
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 03
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Server (Digital)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/0
Frames Errors, Rx/Tx......... 0/2 (0,0%/0,4%)
Frames Count, Rx/Tx.......... 599/545
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 13
Error Control Link NAKs...... 2
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 38 207
Characters Sent.............. 26 622
Average CPS, Rx/Tx........... 130/90
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 64


Inpro IDC Modems Diagnostics, Version 1.0.2.33
23.01.2004 17:33:05 - Outbound Call by RemoteAccess
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.24

Time Online.................. 00:04:53
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 28800/28800/28800/28800 bps
Rx Rate (Last/Init/Min/Max).. 38667/38667/38667/38667 bps
Modulation................... V.90
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 34
Tx/Power Drop/Rx Level....... 15/0/21
SNR Last/Min/Max............. 43/43/43
Highest Rx/Tx State.......... 67/67
EQM Sum...................... 00E9
RBS Pattern.................. 00
Rate Drop.................... 0
Digital Loss................. 2000
Retrains Issued/Granted/Auto. 0/2/0
Renegs Issued/Granted........ 0/0
FForwards/FBacks/Denied...... 0/0/0
Forced FB/FB after FF/MaxREJ. 0/0/0
Last dialed number........... T7311111
V90 9481834347E5


Negotiation Result (Rx/Tx)... V.90 Issue 1 (asymmetric)/V.34
Symbol Rate (Rx/Tx).......... 8000/3200
Carrier Frequency Hz, Tx..... 1829
EQM Value (Last/Min/Max)..... 34/28/42
EQM Hits..................... 0
EQM Last 10 Readings......... 36 37 34 32 30 32 32 32 38 34
Last Retrain/Reneg Status.... Remote Retrain
Last Retrain/Reneg Reason.... Remote Retrain
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 23 seconds/0
Non-linear Encoding, Rx/Tx... OFF/ON
Precoding, Rx/Tx............. OFF/ON
Shaping, Rx/Tx............... OFF/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 2
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 3,2
Last Rx/Tx State............. 67/67
Energy at 3750Hz/Average .... 3782/2069
Auto Gain Amplitude, db...... 10
AGC Gain (Last/Min/Max)...... 85/85/85
Detection of 120 Hz Tones.... Yes
Detection of Dual PCM........ No
V.90 RBS Pattern............. 00
V.90 Alternating RBS Pattern. 00
V.90 Digital Pad Value, db... 0,0
V.90 Optimal Speed........... 38667 bps (Reg.S120=9)
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 03
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Server (Digital)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/0
Frames Errors, Rx/Tx......... 0/2 (0,0%/0,4%)
Frames Count, Rx/Tx.......... 599/545
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 13
Error Control Link NAKs...... 2
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 38 207
Characters Sent.............. 26 622
Average CPS, Rx/Tx........... 130/90
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 64

Inpro IDC Modems Diagnostics, Version 1.0.2.33
23.01.2004 17:20:32 - Outbound Call by RemoteAccess
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.24

Time Online.................. 00:01:38
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 28800/28800/28800/28800 bps
Rx Rate (Last/Init/Min/Max).. 38667/38667/38667/38667 bps
Modulation................... V.90
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 31
Tx/Power Drop/Rx Level....... 15/0/21
SNR Last/Min/Max............. 43/43/43
Highest Rx/Tx State.......... 67/67
EQM Sum...................... 00F1
RBS Pattern.................. 00
Rate Drop.................... 0
Digital Loss................. 2000
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 0/0
FForwards/FBacks/Denied...... 0/0/0
Forced FB/FB after FF/MaxREJ. 0/0/0
Last dialed number........... T7311111
V90 9481834347E5


Negotiation Result (Rx/Tx)... V.90 Issue 1 (asymmetric)/V.34
Symbol Rate (Rx/Tx).......... 8000/3200
Carrier Frequency Hz, Tx..... 1829
EQM Value (Last/Min/Max)..... 31/25/35
EQM Hits..................... 0
EQM Last 10 Readings......... 32 31 34 32 26 32 32 31 30 31
Last Retrain/Reneg Status.... None
Last Retrain/Reneg Reason.... None
Last Retrain/Reneg Time...... 1 minutes ago
Handshake Time/Retries....... 23 seconds/0
Non-linear Encoding, Rx/Tx... OFF/ON
Precoding, Rx/Tx............. OFF/ON
Shaping, Rx/Tx............... OFF/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 3
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 4,4
Last Rx/Tx State............. 67/67
Energy at 3750Hz/Average .... 3979/2154
Auto Gain Amplitude, db...... 10
AGC Gain (Last/Min/Max)...... 85/85/85
Detection of 120 Hz Tones.... Yes
Detection of Dual PCM........ No
V.90 RBS Pattern............. 00
V.90 Alternating RBS Pattern. 00
V.90 Digital Pad Value, db... 0,0
V.90 Optimal Speed........... 38667 bps (Reg.S120=9)
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 03
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Server (Digital)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/0
Frames Errors, Rx/Tx......... 0/0 (0,0%/0,0%)
Frames Count, Rx/Tx.......... 91/136
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 2
Error Control Link NAKs...... 0
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 11 060
Characters Sent.............. 5 413
Average CPS, Rx/Tx........... 112/55
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 64

[Technical Support]

Скорее всего, в розетке всего лишь имитация заземления

Проверить можно вольтметром, как и предлагалось раньше. Меряете переменное напряжение между корпусом компьютера и каждым из проводов телефонной линии. Если заземление есть, напряжение не будет превышать 1В. При отсутствии оно, как правило, составляет 90-110В.
_________________
Inpro
Technical Support

[PaulU]

Здраствуйте! Я померял напряжение между задней крышкой корпуса и каждым проводом телефонной линии. Получилось 110В как в заземленной (якобы) так и в не заземленной розетках. Правда у меня интегрированная сетевая карта.

Решил сравнить эти 2 розетки, чем же они отличаются. Если вставить один провод в фазу, а другой в землю, то получается 220В на заземленной розетке, и несколько вольт на незаземленной!!!

КАК ПРОВЕРИТЬ ЗАЗЕМЛЕНА РОЗЕТКА РЕАЛЬНО ИЛИ НЕТ?

[Technical Support]

Вы уже проверили. Заземления нет. При наличии заземления переменное напряжение между корпусом и любым из проводов телефонной линии не превышает 1В.
_________________
Inpro
Technical Support

[PaulU]

а сетевая карта ни как не влияет на это напряжение?