Предыдущая тема :: Следующая тема |
Автор |
Сообщение |
DomY Junior member
Зарегистрирован: 30.05.2004 Сообщения: 4
|
Добавлено: Вс Май 30, 2004 8:01 pm Заголовок сообщения: буду очень благодарен за Ваши рекомендации по настройке |
|
|
Поздравляю Вас с прибавлением в армии поклонников модемов IDC!
Вот собрал статистику, в командной строке ничего не писал.
Если можно что-нибудь выжать из моей линии,
буду очень благодарен за Ваши рекомендации по настройке:
--------------------------------------------------------
Inpro IDC Modems Diagnostics, Version 1.0.2.33
30.05.2004 20:34:47 - Direct Log Write Entry
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.24
Time Online.................. 00:38:35
Termination Reason........... KEY ABORT
Tx Rate (Last/Init/Min/Max).. 16800/16800/ 9600/19200 bps
Rx Rate (Last/Init/Min/Max).. 28800/28800/ 9600/31200 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 31
Tx/Power Drop/Rx Level....... 15/1/24
SNR Last/Min/Max............. 39/36/39
Highest Rx/Tx State.......... 85/87
EQM Sum...................... 0053
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 1/15/0
Renegs Issued/Granted........ 51/15
FForwards/FBacks/Denied...... 19/33/0
Forced FB/FB after FF/MaxREJ. 33/10/11
Last dialed number........... PXXXXXXX
Flex fail 9481834347EB
Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 3429
Carrier Frequency Hz, Rx/Tx.. 1959/1959
EQM Value (Last/Min/Max)..... 31/0/127
EQM Hits..................... 0
EQM Last 10 Readings......... 34 32 30 31 29 31 32 28 31 33
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Reason for V.34 Fallback..... Data Pump decision to Fallback in Phase 2
Last Retrain/Reneg Time...... 1 minutes ago
Handshake Time/Retries....... 29 seconds/0
Non-linear Encoding, Rx/Tx... ON/ON
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 3
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 4,3
Last Rx/Tx State............. 85/87
Energy at 3750Hz/Average .... 156/321
AGC Gain (Last/Min/Max)...... 79/67/79
Detection of 120 Hz Tones.... Yes
Detection of Dual PCM........ Yes
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 03
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Server (Digital)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Unknown
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/171
Frames Errors, Rx/Tx......... 683/28 (2,0%/0,3%)
Frames Count, Rx/Tx.......... 33476/9552
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 35
Error Control Link NAKs...... 28
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 4 430 473
Characters Sent.............. 650 585
Average CPS, Rx/Tx........... 1913/281
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 63 |
|
Вернуться к началу |
|
|
Technical Support Expert
Зарегистрирован: 31.10.2002 Сообщения: 6330
|
Добавлено: Вс Май 30, 2004 8:49 pm Заголовок сообщения: |
|
|
Первое, что Вам нужно сделать - избавиться от перетренировок, запрашиваемых удалённым модемом (там - сервер CISCO, это у них болезнь):
Retrains Issued/Granted/Auto. 1/15/0
Пропишите в строке инициализации в свойствах модема в Windows такие команды:
S91=15 S210.7=1 +MS=11,,,,,,9600
и покажите, что получится в статистике. _________________ Inpro
Technical Support |
|
Вернуться к началу |
|
|
DomY Junior member
Зарегистрирован: 30.05.2004 Сообщения: 4
|
Добавлено: Вс Май 30, 2004 10:44 pm Заголовок сообщения: В командной строке прописал,вот что из этого выходит: |
|
|
Inpro IDC Modems Diagnostics, Version 1.0.2.33
30.05.2004 23:20:08 - Direct Log Write Entry
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.24
Time Online.................. 00:07:04
Termination Reason........... LINK DISCONNECT
Tx Rate (Last/Init/Min/Max).. 9600/ 9600/ 9600/ 9600 bps
Rx Rate (Last/Init/Min/Max).. 24000/26400/24000/28800 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 57
Tx/Power Drop/Rx Level....... 15/0/27
SNR Last/Min/Max............. 32/32/32
Highest Rx/Tx State.......... 65/87
EQM Sum...................... 011B
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/2/0
Renegs Issued/Granted........ 4/0
FForwards/FBacks/Denied...... 1/3/0
Forced FB/FB after FF/MaxREJ. 2/0/7
Last dialed number........... PXXXXXXX
Flex fail
Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 3429
Carrier Frequency Hz, Rx/Tx.. 1959/1959
EQM Value (Last/Min/Max)..... 57/16/127
EQM Hits..................... 0
EQM Last 10 Readings......... 122 121 37 40 33 34 36 37 35 38
Last Retrain/Reneg Status.... Remote Retrain
Last Retrain/Reneg Reason.... Remote Retrain
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 26 seconds/0
Non-linear Encoding, Rx/Tx... ON/OFF
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 3
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 3,7
Last Rx/Tx State............. 65/67
Energy at 3750Hz/Average .... 128/18
AGC Gain (Last/Min/Max)...... 69/33/71
Detection of 120 Hz Tones.... No
Detection of Dual PCM........ No
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:T UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/44
Frames Errors, Rx/Tx......... 44/0 (3,9%/0,0%)
Frames Count, Rx/Tx.......... 1132/659
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 2
Error Control Link NAKs...... 0
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 127 634
Characters Sent.............. 61 135
Average CPS, Rx/Tx........... 301/144
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 59
Inpro IDC Modems Diagnostics, Version 1.0.2.33
30.05.2004 23:38:43 - Outbound Call by RemoteAccess
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.24
Time Online.................. 00:16:48
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 9600/ 9600/ 9600/ 9600 bps
Rx Rate (Last/Init/Min/Max).. 21600/26400/19200/26400 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 36
Tx/Power Drop/Rx Level....... 15/0/30
SNR Last/Min/Max............. 29/29/29
Highest Rx/Tx State.......... 85/87
EQM Sum...................... 0090
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 12/0
FForwards/FBacks/Denied...... 6/6/0
Forced FB/FB after FF/MaxREJ. 3/1/9
Last dialed number........... PXXXXXXX
Flex fail
Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 3429
Carrier Frequency Hz, Rx/Tx.. 1959/1959
EQM Value (Last/Min/Max)..... 36/7/127
EQM Hits..................... 0
EQM Last 10 Readings......... 40 57 51 36 30 39 37 33 31 37
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallforward due to Low EQM
Last Retrain/Reneg Time...... 4 minutes ago
Handshake Time/Retries....... 26 seconds/0
Non-linear Encoding, Rx/Tx... ON/ON
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 2
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 3,7
Last Rx/Tx State............. 85/87
Energy at 3750Hz/Average .... 413/302
AGC Gain (Last/Min/Max)...... 61/61/62
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/110
Frames Errors, Rx/Tx......... 110/3 (0,9%/0,1%)
Frames Count, Rx/Tx.......... 12816/4880
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 9
Error Control Link NAKs...... 3
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 1 695 745
Characters Sent.............. 418 932
Average CPS, Rx/Tx........... 1682/415
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 59 |
|
Вернуться к началу |
|
|
Technical Support Expert
Зарегистрирован: 31.10.2002 Сообщения: 6330
|
Добавлено: Пн Май 31, 2004 10:44 am Заголовок сообщения: |
|
|
Хотелось бы посмотреть на статистики модема при полной загрузке канала на приём. Скачайте какой-нибудь архивированный файл с сервера провайдера. Проведите два эксперимента: один с рекомендованной ранее строкой инициализации, а перед началом второго добавьте в начало строки инициализации команду:
S210.4=1 _________________ Inpro
Technical Support |
|
Вернуться к началу |
|
|
DomY Junior member
Зарегистрирован: 30.05.2004 Сообщения: 4
|
Добавлено: Пн Май 31, 2004 5:41 pm Заголовок сообщения: Высылаю 2 лога |
|
|
Лог с рекомендованной ранее строкой инициализации:
-----------------------------------------------------
Inpro IDC Modems Diagnostics, Version 1.0.2.33
31.05.2004 18:10:12 - Direct Log Write Entry
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.24
Time Online.................. 00:06:26
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 9600/ 9600/ 7200/ 9600 bps
Rx Rate (Last/Init/Min/Max).. 24000/24000/21600/28800 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 22
Tx/Power Drop/Rx Level....... 15/0/24
SNR Last/Min/Max............. 39/39/39
Highest Rx/Tx State.......... 85/87
EQM Sum...................... 010F
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 4/2
FForwards/FBacks/Denied...... 2/2/0
Forced FB/FB after FF/MaxREJ. 1/0/7
Last dialed number........... PXXXXXXX
Flex fail
Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 3429
Carrier Frequency Hz, Rx/Tx.. 1959/1959
EQM Value (Last/Min/Max)..... 22/5/127
EQM Hits..................... 0
EQM Last 10 Readings......... 22 22 20 23 20 22 21 28 38 21
Last Retrain/Reneg Status.... Remote Rate Renegotiation
Last Retrain/Reneg Reason.... Remote Rate Renegotiation
Last Retrain/Reneg Time...... 1 minutes ago
Handshake Time/Retries....... 25 seconds/0
Non-linear Encoding, Rx/Tx... ON/ON
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 4
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 4,3
Last Rx/Tx State............. 67/87
Energy at 3750Hz/Average .... 664/473
AGC Gain (Last/Min/Max)...... 76/75/77
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/62
Frames Errors, Rx/Tx......... 62/0 (0,9%/0,0%)
Frames Count, Rx/Tx.......... 7007/1231
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 3
Error Control Link NAKs...... 0
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 809 980
Characters Sent.............. 40 312
Average CPS, Rx/Tx........... 2098/104
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 63
---------------------------------------------
Лог с командой S210.4=1 S91=15 S210.7=1 +MS=11,,,,,,9600
Inpro IDC Modems Diagnostics, Version 1.0.2.33
31.05.2004 18:32:48 - Direct Log Write Entry
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.24
Time Online.................. 00:07:25
Termination Reason........... KEY ABORT
Tx Rate (Last/Init/Min/Max).. 9600/ 9600/ 9600/ 9600 bps
Rx Rate (Last/Init/Min/Max).. 33600/31200/26400/33600 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 43
Tx/Power Drop/Rx Level....... 15/0/25
SNR Last/Min/Max............. 37/37/37
Highest Rx/Tx State.......... 85/87
EQM Sum...................... 004D
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 10/0
FForwards/FBacks/Denied...... 7/3/0
Forced FB/FB after FF/MaxREJ. 0/0/0
Last dialed number........... PXXXXXXX
Flex fail
Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 3429
Carrier Frequency Hz, Rx/Tx.. 1959/1959
EQM Value (Last/Min/Max)..... 43/9/127
EQM Hits..................... 0
EQM Last 10 Readings......... 72 45 44 45 45 58 45 45 45 29
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallforward due to Low EQM
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 25 seconds/0
Non-linear Encoding, Rx/Tx... ON/ON
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 4
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 3,7
Last Rx/Tx State............. 85/87
Energy at 3750Hz/Average .... 423/183
AGC Gain (Last/Min/Max)...... 72/72/73
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/214
Frames Errors, Rx/Tx......... 214/2 (1,9%/0,1%)
Frames Count, Rx/Tx.......... 11512/2141
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 5
Error Control Link NAKs...... 2
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 1 277 859
Characters Sent.............. 65 567
Average CPS, Rx/Tx........... 2871/147
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 62 |
|
Вернуться к началу |
|
|
Technical Support Expert
Зарегистрирован: 31.10.2002 Сообщения: 6330
|
Добавлено: Пн Май 31, 2004 6:07 pm Заголовок сообщения: |
|
|
Пожалуй, что стоит оставить последний вариант (с S210.4=1). Всё, настройка окончена _________________ Inpro
Technical Support |
|
Вернуться к началу |
|
|
DomY Junior member
Зарегистрирован: 30.05.2004 Сообщения: 4
|
Добавлено: Пн Май 31, 2004 6:25 pm Заголовок сообщения: |
|
|
Спасибо! |
|
Вернуться к началу |
|
|
|
|
Вы не можете начинать темы Вы не можете отвечать на сообщения Вы не можете редактировать свои сообщения Вы не можете удалять свои сообщения Вы не можете голосовать в опросах
|
Powered by phpBB © 2001, 2005 phpBB Group
|