помогите со строкой инициализации для модема!

[siberian]

в связи с переполохом и катаклизмом утерял старую строку, да и к тому же сменил провайдера.... помогите... пожалуйста =)

вот статистика:

Inpro IDC Modems Diagnostics, Version: 1.1.4.39
28.01.2006 10:14:30 - Clipboard Copy
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.24
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String:

Time Online.................. 00:10:19
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 12000/24000/12000/24000 bps
Rx Rate (Last/Init/Min/Max).. 26400/28800/26400/28800 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 19
Tx/Power Drop/Rx Level....... 15/3/16
SNR Last/Min/Max............. 34/34/34
Highest Rx/Tx State.......... 85/87
EQM Sum...................... 004E
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/2/0
Renegs Issued/Granted........ 3/26
FForwards/FBacks/Denied...... 0/3/0
Forced FB/FB after FF/MaxREJ. 3/1/8
Last dialed number........... P370000
Flex fail 9481834347E4


Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 3200
Carrier Frequency Hz, Rx/Tx.. 1829/1829
EQM Value (Last/Min/Max)..... 19/12/51
EQM Hits..................... 0
EQM Last 10 Readings......... 21 21 19 18 19 22 20 18 22 20
Last Retrain/Reneg Status.... Remote Rate Renegotiation
Last Retrain/Reneg Reason.... Remote Rate Renegotiation
Reason for V.34 Fallback..... Data Pump decision to Fallback in Phase 2
Last Retrain/Reneg Time...... 1 minutes ago
Handshake Time/Retries....... 27 seconds/1
Non-linear Encoding, Rx/Tx... OFF/ON
Precoding, Rx/Tx............. OFF/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 5
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 6,3
Last Rx/Tx State............. 85/87
Energy at 3750Hz/Average .... 64/31
Auto Gain Amplitude, db...... 10
Rx Level (Last/Min/Max), -dB. 15,7/17,2/15,7
Detection of 120 Hz Tones.... Yes
Detection of Dual PCM........ No
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 03
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Server (Digital)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... External
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/140
Frames Errors, Rx/Tx......... 140/32 (1,3%/1,0%)
Frames Count, Rx/Tx.......... 11074/3295
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 32
Error Control Link NAKs...... 32
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 1 143 587
Characters Sent.............. 89 030
Average CPS, Rx/Tx........... 1847/143
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 50

заранее спасиба

[Technical Support]

Попробуйте так:

S91=15 S210.7=1 S202.3=1 +MS=11,,,,,,19200
_________________
Inpro
Technical Support

[siberian]

вот что получилось с новой строкой:

Inpro IDC Modems Diagnostics, Version: 1.1.4.39
28.01.2006 15:25:27 - Clipboard Copy
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.24
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: m4 S91=15 S210.7=1 S202.3=1 +MS=11,,,,,,19200

Time Online.................. 00:13:37
Termination Reason........... NO REMOTE RESPONSE
Tx Rate (Last/Init/Min/Max).. 16800/19200/16800/19200 bps
Rx Rate (Last/Init/Min/Max).. 26400/28800/26400/28800 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 126
Tx/Power Drop/Rx Level....... 15/0/19
SNR Last/Min/Max............. 34/34/34
Highest Rx/Tx State.......... 67/87
EQM Sum...................... 0000
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 8/1
FForwards/FBacks/Denied...... 3/5/0
Forced FB/FB after FF/MaxREJ. 4/2/10
Last dialed number........... P370000
Flex fail


Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 3000
Carrier Frequency Hz, Rx/Tx.. 1800/1800
EQM Value (Last/Min/Max)..... 126/16/127
EQM Hits..................... 0
EQM Last 10 Readings......... 127 127 125 125 127 127 24 23 28 24
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 18 seconds/0
Non-linear Encoding, Rx/Tx... ON/ON
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 5
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 5,5
Last Rx/Tx State............. 67/84
Energy at 3750Hz/Average .... 32/14
Rx Level (Last/Min/Max), -dB. 18,3/47,6/18,3
Detection of 120 Hz Tones.... No
Detection of Dual PCM........ No
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 0/219
Frames Errors, Rx/Tx......... 219/51 (1,1%/1,1%)
Frames Count, Rx/Tx.......... 19582/4497
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 6
Error Control Link NAKs...... 51
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 2 119 634
Characters Sent.............. 112 775
Average CPS, Rx/Tx........... 2594/138
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 53

хотелось бы поменьше пересогласовок... побольше стабильности...

[Technical Support]

[siberian]

каждая пересогласовка скорости прекращает на время передачу данных..... Играть в таких условиях, когда каждую минуту пересогласовка, например в Warcraft 3 по инету почти невозможно! В этом смысле я употребил фразу "побольше стабильности".
Хотелось бы избавится от пересогласовок вобщем... =)

[Technical Support]

Избавиться от пересогласований можно за счёт снижения скорости. "Зажимать скорость нужно командой +MS. Начните с такой:

+MS=11,,,26400
_________________
Inpro
Technical Support

[siberian]

Inpro IDC Modems Diagnostics, Version: 1.1.4.39
28.01.2006 19:47:02 - Clipboard Copy
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.24
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: m4 S91=15 S210.7=1 S202.3=1 +MS=11,,,26400,,,19200

Time Online.................. 00:14:13
Termination Reason........... NO REMOTE RESPONSE
Tx Rate (Last/Init/Min/Max).. 16800/19200/16800/19200 bps
Rx Rate (Last/Init/Min/Max).. 26400/26400/24000/26400 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 126
Tx/Power Drop/Rx Level....... 15/0/18
SNR Last/Min/Max............. 36/36/36
Highest Rx/Tx State.......... 67/87
EQM Sum...................... 0000
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 3/3
FForwards/FBacks/Denied...... 1/2/0
Forced FB/FB after FF/MaxREJ. 1/0/7
Last dialed number........... P370000
Flex fail


Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 3000
Carrier Frequency Hz, Rx/Tx.. 1800/1800
EQM Value (Last/Min/Max)..... 126/9/127
EQM Hits..................... 0
EQM Last 10 Readings......... 127 127 125 125 127 127 17 17 16 17
Last Retrain/Reneg Status.... Local Rate Renegotiation
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 17 seconds/0
Non-linear Encoding, Rx/Tx... ON/ON
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 5
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 5,5
Last Rx/Tx State............. 67/84
Energy at 3750Hz/Average .... 32/15
Rx Level (Last/Min/Max), -dB. 16,8/47,6/16,8
Detection of 120 Hz Tones.... No
Detection of Dual PCM........ No
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 0/138
Frames Errors, Rx/Tx......... 138/58 (0,8%/1,1%)
Frames Count, Rx/Tx.......... 17761/5446
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 14
Error Control Link NAKs...... 58
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 2 043 118
Characters Sent.............. 136 130
Average CPS, Rx/Tx........... 2395/159
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 54

..... >Renegs Issued/Granted........ 3/3
похоже придется еще уменьшать скорость?

[Technical Support]

Да, придётся ещё снижать скорость, причём не только приёма, но и передачи. Дополнительно, стОит попробовать запретить модему реагировать на сбойный кадры при приёме данных. Строка инициализации:

S91=15 S210.7=1 S210.4=1 S202.3=1 +MS=11,,,24000,,,14400
_________________
Inpro
Technical Support

[siberian]

поставил строку и вот что получилось:
Inpro IDC Modems Diagnostics, Version: 1.1.4.39
29.01.2006 9:31:47 - Clipboard Copy
--------------------------------------------------------
Modem Type: IDC-5614BXL/VR+ (Plus) Firmware Revision: V2.24
System Modem Init String: AT&FS38=0S95=41S115=0E0<cr>
User Modem Init String: S91=15 S210.7=1 S210.4=1 S202.3=1 +MS=11,,,24000,,,14400

Time Online.................. 00:18:59
Termination Reason........... LOCAL REQUEST
Tx Rate (Last/Init/Min/Max).. 14400/14400/14400/14400 bps
Rx Rate (Last/Init/Min/Max).. 24000/24000/24000/24000 bps
Modulation................... V.34bis
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 8
Tx/Power Drop/Rx Level....... 15/0/25
SNR Last/Min/Max............. 36/36/36
Highest Rx/Tx State.......... 85/87
EQM Sum...................... 0031
RBS Pattern.................. NA
Rate Drop.................... NA
Digital Loss................. None
Retrains Issued/Granted/Auto. 0/0/0
Renegs Issued/Granted........ 0/36
FForwards/FBacks/Denied...... 0/0/0
Forced FB/FB after FF/MaxREJ. 0/0/0
Last dialed number........... P370000
Flex fail


Negotiation Result (Rx/Tx)... V.34/V.34
Symbol Rate.................. 3200
Carrier Frequency Hz, Rx/Tx.. 1829/1829
EQM Value (Last/Min/Max)..... 8/5/67
EQM Hits..................... 0
EQM Last 10 Readings......... 7 8 9 8 8 8 8 8 7 9
Last Retrain/Reneg Status.... Remote Rate Renegotiation
Last Retrain/Reneg Reason.... Remote Rate Renegotiation
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 17 seconds/0
Non-linear Encoding, Rx/Tx... ON/ON
Precoding, Rx/Tx............. ON/ON
Shaping, Rx/Tx............... ON/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 5
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 5,7
Last Rx/Tx State............. 85/87
Energy at 3750Hz/Average .... 39/14
Rx Level (Last/Min/Max), -dB. 24,6/25,0/24,6
Detection of 120 Hz Tones.... No
Detection of Dual PCM........ No
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Error Correction Status Byte. ADP:R ODP:T
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 1/23
Frames Errors, Rx/Tx......... 23/5 (0,1%/0,1%)
Frames Count, Rx/Tx.......... 15908/4307
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 17
Error Control Link NAKs...... 5
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 1 942 316
Characters Sent.............. 121 698
Average CPS, Rx/Tx........... 1705/106
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 61

комментируйте пожалуйста...

[Technical Support]

Плохи дела Это значит, что удалённый модем слишком глуп, чтобы понять, что Вы ограничили скорость передачи (т.е. его скорость приёма). Вместо того, чтобы тихо и смирно работать на 14400, как Вы просили, он постоянно (и конечно же, безуспешно) пытался поднять скорость (сделать fall-forward):

Renegs Issued/Granted........ 0/36
Tx Rate (Last/Init/Min/Max).. 14400/14400/14400/14400 bps

Получается, что ограничивать скорость передачи нельзя, от этого только хуже. Надо заменить строку инициализации на такую:

S91=15 S210.7=1 S210.4=1 S202.3=1 +MS=11,,,24000

Естественно, при этом удалённый модем может запрашивать пересогласования, но их будет гораздо меньше, чем было в этот раз. И придётся с такой ситуацией смириться.
_________________
Inpro
Technical Support